[Users] Ovirt allinone exists during setup

[Ohad Basan]

hey
thanks for the answer.

1. where exactly do i see the state of the host
2. I did as you instructed. the setup fails exactly at the same step (I
changed the timeout to 600, shut down networkmanager and connected via dhcp
over ethernet.
2. I manually configured as following

/etc/sysconfig/network-scripts/ifcfg-ovirtmgmt
DEVICE=ovirtmgmt
TYPE=Bridge
ONBOOT=yes
DELAY=0
BOOTPROTO=dhcp
NM_CONTROLLED="no

and added
BRIDGE=ovirtmgmt
to the ifcfg-eth0


restarting the network service fails with a status error
RTNETLINK answers: File exists.

thanks


On Mon, Jun 18, 2012 at 11:21 AM, Ofer Schreiber <oschreib at redhat.com>wrote:

> >
> > the bootstrap logs are also available
> > here they are.
> > thanks.
>
> 1. If you log into the GUI, in which state is the host?
>
> 2. From the engine.log, I can see that the host installation went fine,
> and it seems that the host is in "Non-Operetional state).
>   - I can see clearly in the log :"Host local_host is set to
> Non-Operational, it is missing the following networks: ovirtmgmt"
>
> 3. in the vds_bootstrap.498578.log you can see "ERROR    _getBridgeParams:
> failed to read params of file /etc/sysconfig/network-scripts/ifcfg-wlan0."
> - it seems that something is wrong with your networking configuration
>
> 4. Probably the timeout during all-in-one installation (150 seconds) is
> too low for you.
>
>
> Two options for you:
> 1. Clean everything (using engine-cleanup), fix you networking settings
> (disable NetworkManager, use non wireless conntection) and rerun
> engine-setup (with higher timeout in
> /usr/share/ovirt-engine/scripts/plugins/all_in_one_100.py)
>
> 2. Just create the ovirtmgmt network bridge by your self, and restart vdsm.
>
> >
> >
> >
> > On Mon, Jun 18, 2012 at 10:40 AM, Ofer Schreiber <
> > oschreib at redhat.com > wrote:
> >
> >
> >
> >
> >
> > ----- Original Message -----
> > >
> > > The log is attached.
> > >
> > > thanks
> >
> > I'm missing the vds_bootstrap* logs. are they available?
> > if not, if you log into the GUI, in which state the host is currently
> > at?
> >
> > (/var/log/ovirt-enging/*log might help as well)
> >
> >
> >
> > >
> > >
> > >
> > > On Mon, Jun 18, 2012 at 10:26 AM, Ofer Schreiber <
> > > oschreib at redhat.com > wrote:
> > >
> > >
> > > It seems that the host is currently in "installing" state.
> > > Could you please take a look (or attach us) the vdsm installation
> > > logs under /tmp?
> > > (/tmp/vds_*)
> > >
> > >
> > >
> > > ----- Original Message -----
> > > >
> > > > Hello.
> > > >
> > > > I'm experiencing a problem during installation of the ovirt
> > > > engine
> > > > including the all-in-one plugin
> > > > The setup exists during the stage "Adding local host" - it quits
> > > > due
> > > > to a "time out while waiting for the host to start"
> > > > I've attached some info (including the setup's log) and will
> > > > gladly
> > > > provide more information if necessary.
> > > >
> > > > Many thanks,
> > > >
> > > > Ohad
> > > >
> > > >
> > >
> > >
> >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20120618/9b7127ca/attachment.html>