<div dir="ltr"><div class="gmail_extra"><div class="gmail_quote">On Thu, Jan 18, 2018 at 9:52 PM, Abdurrahman A. Ibrahim <span dir="ltr">&lt;<a href="mailto:a.rahman.attia@gmail.com" target="_blank">a.rahman.attia@gmail.com</a>&gt;</span> wrote:<br><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto">Hello,<div dir="auto"><br></div><div dir="auto">I am planning to buy home lab hardware to be used by oVirt.</div><div dir="auto"><br></div><div dir="auto">Any recommendations for used hardware i can buy from eBay for example? </div><div dir="auto">Also, have you tried oVirt on Intel NUC or any other SMB servers before? </div><div dir="auto"><br></div><div dir="auto">Thanks, </div><div dir="auto">Ab</div></div></blockquote><div><br></div><div>I&#39;m currently using:</div><div><br></div><div>NUC6i5SYH since 2015 without any problem</div><div>it&#39;s rock solid with 2xssd disks and 16Gb of ram</div><div>oVirt as single host with hosted engine and connected through a 24&quot; monitor via hdmi </div><div>I use it as my home/work station, normally working on a VM (currently Fedora 27) inside this oVirt infra (currently 4.2.0) + other VMs</div><div>In the host (plain CentOS 7.4) I installed firefox browser and from there I connect to the engine VM (running on itself) and from there to the F27 VM through Spice</div><div>I use this F27 VM in full screen so it is like it is my pc itself....</div><div>Probably over-complicated, but I use it to have a constant feeling with oVirt and its functionalities...</div><div>No problem at all from the usability point of view (I don&#39;t use heavy graphic, so the setup is ok for me, it could not be for you)</div><div>The only problem is when you indeed have to power off the NUC, because if you simply restart, it has problems (apparently) syncing with the monitor (as Jamie noted).</div><div>My simple workaround when I have to reboot the NUC (I think 4-5 times in 3 years basically to update oVirt and together the bios) has been:</div><div>- shutdown the infra</div><div>- the NUC tends to restart and not poweroff</div><div>- keep power button pressed so the NUC powers off</div><div>- power off monitor</div><div>- detach and reconnect the hdmi cable</div><div>- power on monitor</div><div>- power on NUC</div><div><br></div><div>If you have to daily restart the pc this can be annoying for sure.</div><div>I didn&#39;t now about a general NUC problem, so I thought it was my particular combination NUC/Monitor (Dell U2515H) and CentOS drivers for the graphic adapter.</div><div>I have to say that in 2015 when I bought it I both tried to install CentOS 7.x at that time and Fedaora 24 at that time and the display problems were present only in CentOS.</div><div>And after various CentOS updates (now on 7.4  updates) it seems to me it is quite better, so I think the problems discussed by Jamie could have been resolved in CentOS  too.</div><div><br></div><div>I have also another NUC in another site. This is NUC6i3SYH again with 2xssd and 16Gb of ram</div><div>It has ESXi free 6.0.2 with some VMs and a nested HCI oVirt environment (now at 4.2.1 rc1)</div><div>It is not connected through a monitor and it works ok.</div><div>I connected the monitor only when I had to install and/or reboot (probably 2-3 times in 2,5 years).</div><div>Now it is powered on since 8 months...</div><div><br></div><div>Both the NUCs are connected to an APC UPS</div><div><br></div><div>No experience on other similar hw, because I felt good with the NUCs for my needs.</div><div> </div><div>HIH for your choice,</div><div>Gianluca</div><div><br></div><div><br></div><div><br></div></div></div></div>