I've tested F17 on IBM bladeservers (HS20,HS21,HS22,HS22V) It's been
installed correctly with UEFI as well as with legacy.
Unfortunately I cannot check bladecenter with ovirt-node right now.
Which bladeserver have you tested?
--
Best regards, Pavel Zhukov
mailto:pavel@zhukoff.net
On Sun, 18 Nov 2012, Nicholas Kesick wrote:> ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
> Node is based on Fedora 17, so if you have the same problem with
> both, that means it is likely upstream on the Fedora end of things. Fedora 18
> is due to have support for UEFI, but release has been delayed until Jan 8th at
> the earliest. If Fedora 18 works, I'd say you'll likely be able to use an oVirt
> Node based on F18.
>
> Any way to disable UEFI on your server?
>
> - Nick
>
> From: kurmakwana@gmail.com
> Date: Sun, 18 Nov 2012 22:39:53 +0530
> To: users@ovirt.org
> Subject: Re: [Users] Unable to install ovirt node on IBM system X blade server
>
> Hello Ovirt Users,
>
> Did anyone else also faced same issue or ovirt node not getting installed and
> servers just reboots when option to install / upgrade / reinstall is used.
>
> Its on IBM system X server with UEFI. I've tried both latest Ovirt node and
> Fedora 17 also. Both gives same behavior or just reboot in loop and nothing
> else. I am unable to take ovirt further in my office at this moment.
>
> Kindly advice.
>
> Regards,
> Keyur
>
> On Fri, Nov 16, 2012 at 8:09 PM, Keyur Makwana <kurmakwana@gmail.com> wrote:
>
> Hello All,
>
> Same is the case with Fedora install on this IBM server I am using.
>
> Regards,
> Keyur
>
>
> On Fri, Nov 16, 2012 at 12:31 PM, Keyur Makwana <kurmakwana@gmail.com>
> wrote:
>
> Hi All,
>
> I've been trying to install latest ovirt node on IBM system X blade
> server (UEFI based server) but not even able to start the installation.
>
> I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from http://
> ovirt.org/releases/3.1/tools/
>
> Server boots up and detects the ISO, gives me initial screen of Install
> or Upgrade / Reinstall etc. but the moment default install is selected
> (or it goes into default if initial screen is not interrupted for 30
> seconds.) - it just waits for 3-4 seconds and the server is rebooted.
> These problem of server reboot persist with any available option to
> install on the screen.
>
> Note : I was able to successfully install RHEV-H and it worked fine.
> Not sure why ovirt node installation is not even starting and goes into
> infinite reboot loop with doing anything.
>
> Out of curiosity - I tried this version of node as well http://
> jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/
> ovirt-node-iso-2.5.999-999.20121115114700git3d0fec5.446.fc17.iso but
> that too resulted in same behavior.
>
> Request Ovirt experts to assist and help resolve this issue.
>
> Thanks & Regards,
> Keyur
>
>
>
>
>
>
> _______________________________________________ Users mailing list
> Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
> _______________________________________________
> Users mailing list
> Users@ovirt.org
> http://lists.ovirt.org/mailman/listinfo/users