Yes! It is.
After upgrade 4.2 to 4.3 datacenter and cluster compatibility mode was 4.2 when I discovered the issue. Then I set Cluster mode to 4.3 – no luck. It is not so
easy to return it to 4.2.
Thank you!
Best,
Latcho
From: Strahil <hunter86_bg@yahoo.com>
Sent: Sunday, January 12, 2020 2:20 PM
To: Latchezar Filtchev <Latcho@aubg.bg>; users <users@ovirt.org>
Subject: RE: [ovirt-users] Re: Unstable VM network connectivity after upgrade 4.2.8 to 4.3.7
This seems quite odd.
What happens when you set custom compatibility mode to 4.2 ?
I think it was in Edit -> system -> Advanced options -> Custom compatibility mode -> 4.2
Best Regards,
Strahil Nikolov
On Jan 12, 2020 13:24, Latchezar Filtchev <Latcho@aubg.bg> wrote:
Hi Strahil,
Unfortunately virtio drives cannot be used. Guest OS is CentOS 5.2, kernel 2.6.18-92.1.17.el5.centos.plusPAE
The network connectivity of the VM is very short (please see below). Till I connect the VM (via spice) network connectivity is already gone.
tcpdump –I eth0 –v
tcpdump: listening on eth0, link-type EN10MB ( Ethernet ), capture 96 bytes
0 packets captured
0 packets received by filer
0 packets dropped by kernel
From 172.17.17.7 icmp_seq=60 Destination Host Unreachable
From 172.17.17.7 icmp_seq=61 Destination Host Unreachable
From 172.17.17.7 icmp_seq=62 Destination Host Unreachable
From 172.17.17.7 icmp_seq=63 Destination Host Unreachable
From 172.17.17.7 icmp_seq=64 Destination Host Unreachable
From 172.17.17.7 icmp_seq=65 Destination Host Unreachable
64 bytes from 172.17.16.16: icmp_seq=66 ttl=64 time=2.19 ms
64 bytes from 172.17.16.16: icmp_seq=67 ttl=64 time=0.567 ms
64 bytes from 172.17.16.16: icmp_seq=68 ttl=64 time=0.339 ms
64 bytes from 172.17.16.16: icmp_seq=69 ttl=64 time=0.337 ms
64 bytes from 172.17.16.16: icmp_seq=70 ttl=64 time=0.288 ms
64 bytes from 172.17.16.16: icmp_seq=71 ttl=64 time=0.305 ms
64 bytes from 172.17.16.16: icmp_seq=72 ttl=64 time=0.293 ms
64 bytes from 172.17.16.16: icmp_seq=73 ttl=64 time=0.346 ms
64 bytes from 172.17.16.16: icmp_seq=74 ttl=64 time=0.359 ms
64 bytes from 172.17.16.16: icmp_seq=75 ttl=64 time=0.479 ms
64 bytes from 172.17.16.16: icmp_seq=76 ttl=64 time=0.391 ms
64 bytes from 172.17.16.16: icmp_seq=77 ttl=64 time=0.302 ms
64 bytes from 172.17.16.16: icmp_seq=78 ttl=64 time=0.327 ms
64 bytes from 172.17.16.16: icmp_seq=79 ttl=64 time=0.321 ms
From 172.17.17.7 icmp_seq=125 Destination Host Unreachable
From 172.17.17.7 icmp_seq=126 Destination Host Unreachable
From 172.17.17.7 icmp_seq=127 Destination Host Unreachable
From 172.17.17.7 icmp_seq=128 Destination Host Unreachable
Thank you!
Best,
Latcho
From: Strahil Nikolov <hunter86_bg@yahoo.com>
Sent: Sunday, January 12, 2020 12:52 PM
To: users <users@ovirt.org>; Latchezar Filtchev <Latcho@aubg.bg>
Subject: Re: [ovirt-users] Re: Unstable VM network connectivity after upgrade 4.2.8 to 4.3.7
Hi Lacho,
Can you run the virtio drivers ?
They are the most tested in KVM .
Also, can you run a tcpdump (with e1000) and check what is going on when the network disapperead?
Best Regards,
Strahil Nikolov
В неделя, 12 януари 2020 г., 09:22:52 ч. Гринуич+2, Latchezar Filtchev <latcho@aubg.bg> написа:
Dear Strahi,
I tried rtl8139. The behavior is the same.
Best,
Latcho
From: Strahil <hunter86_bg@yahoo.com>
Sent: Sunday, January 12, 2020 1:19 AM
To: Latchezar Filtchev <Latcho@aubg.bg>; users <users@ovirt.org>
Subject: Re: [ovirt-users] Unstable VM network connectivity after upgrade 4.2.8 to 4.3.7
Hi Latcho,
Most probably it's a bug.
Have you tried virtio and/or rtl-based NIC ?As far as I know, CentOS 5 supports Virtio after Kernel >= 2.6.25 .
Best Regards,
Strahil NikolovOn Jan 11, 2020 19:54, Latchezar Filtchev <Latcho@aubg.bg> wrote:
Hello Everyone,
I am aware my guest OS is out of support but I experienced the following:
oVirt – 4.2.8 (self-hosted engine)
VM – CentOS 5.2; two VNIC’s ( driver used e1000) connected to different VLAN’s; - no issues with network connectivity
After upgrade to oVirt 4.3.7
The same VM starts normally. Network is available for several seconds (10 – 20 pings) and then it disappears. The machine works but no ping to/from VM. When I am returning the same machine (via export domain) to oVirt 4.2.8 environment – it works as expected.
Can someone advise on this? Any help will be greatly appreciated.
Thank you.
Best,
Latcho
_______________________________________________
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-leave@ovirt.org
Privacy Statement: https://www.ovirt.org/site/privacy-policy/
oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/
List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/DAPMFAA3XZOUJ2K4PAMOS7O6BULEBRFF/