From /usr/libexec/vdsm/hooks/before_device_create/ovirt_provider_ ovn_hook (installed by ovirt-provider-ovn-driver rpm):
BRIDGE_NAME = 'br-int'
Den 2016-12-28 kl. 23:56, skrev Sverker Abrahamsson:
Googling on the message about br-int suggested adding that bridge to ovs:
ovs-vsctl add-br br-int
Then the VM is able to boot, but it fails to get network connectivity. Output in /var/log/messages:
Dec 28 23:31:35 h2 ovs-vsctl: ovs|00001|vsctl|INFO|Called as ovs-vsctl --timeout=5 -- --if-exists del-port vnet0 -- add-port br-int vnet0 -- set Interface vnet0 "external-ids:attached-mac=\"00:1a:4a:16:01:51\"" -- set Interface vnet0 "external-ids:iface-id=\"e8853 aac-8a75-41b0-8010-e630017dcdd 8\"" -- set Interface vnet0 "external-ids:vm-id=\"b9440d60 -ef5a-4e2b-83cf-081df7c09e6f\" " -- set Interface vnet0 external-ids:iface-status=acti ve
Dec 28 23:31:35 h2 kernel: device vnet0 entered promiscuous mode
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -D PREROUTING -i vnet0 -j libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -D POSTROUTING -o vnet0 -j libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -L libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -L libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X libvirt-J-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F J-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X J-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F J-vnet0-arp-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X J-vnet0-arp-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -D libvirt-out -m physdev --physdev-is-bridged --physdev-out vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -D libvirt-out -m physdev --physdev-out vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -D libvirt-in -m physdev --physdev-in vnet0 -g FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -D libvirt-host-in -m physdev --physdev-in vnet0 -g HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -F FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -X FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -F FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -X FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -F HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -X HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -E FP-vnet0 FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -E FJ-vnet0 FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/iptables -w2 -w -E HJ-vnet0 HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -D libvirt-out -m physdev --physdev-is-bridged --physdev-out vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -D libvirt-out -m physdev --physdev-out vnet0 -g FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -D libvirt-in -m physdev --physdev-in vnet0 -g FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -D libvirt-host-in -m physdev --physdev-in vnet0 -g HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -F FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -X FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -F FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -X FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -F HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -X HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -E FP-vnet0 FO-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -E FJ-vnet0 FI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ip6tables -w2 -w -E HJ-vnet0 HI-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -D PREROUTING -i vnet0 -j libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -D POSTROUTING -o vnet0 -j libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -L libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -L libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X libvirt-I-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -L libvirt-P-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -E libvirt-P-vnet0 libvirt-O-vnet0' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F I-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X I-vnet0-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -F I-vnet0-arp-mac' failed:
Dec 28 23:31:35 h2 firewalld: WARNING: COMMAND_FAILED: '/usr/sbin/ebtables --concurrent -t nat -X I-vnet0-arp-mac' failed:
[root@h2 etc]# ovs-vsctl show
ebb6aede-cbbc-4f4f-a88a-a9cd72b2bd23
Bridge ovirtbridge
Port "ovirtport0"
Interface "ovirtport0"
type: internal
Port ovirtbridge
Interface ovirtbridge
type: internal
Bridge "ovsbridge0"
Port "ovsbridge0"
Interface "ovsbridge0"
type: internal
Port "eth0"
Interface "eth0"
Bridge br-int
Port br-int
Interface br-int
type: internal
Port "vnet0"
Interface "vnet0"
ovs_version: "2.6.90"
Searching through the code it appears that br-int comes from neutron-openvswitch plugin ??
[root@h2 share]# rpm -qf /usr/share/otopi/plugins/ovirt-host-deploy/openstack/neutron _openvswitch.py
ovirt-host-deploy-1.6.0-0.0.master.20161215101008.gitb76ad50 .el7.centos.noarch
/Sverker
Den 2016-12-28 kl. 23:24, skrev Sverker Abrahamsson:
In addition I had to add an alias to modprobe:
[root@h2 modprobe.d]# cat dummy.conf
alias dummy0 dummy
Den 2016-12-28 kl. 23:03, skrev Sverker Abrahamsson:
Hi
I first tried to set device name to dummy_0, but then ifup did not succeed in creating the device unless I first did 'ip link add dummy_0 type dummy' but then it would not suceed to establish the if on reboot.
Setting fake_nics = dummy0 would not work neither, but this works:
fake_nics = dummy*
The engine is now able to find the if and assign bridge ovirtmgmt to it.
However, I then run into the next issue when starting a VM:
2016-12-28 22:28:23,897 ERROR [org.ovirt.engine.core.dal.dbbroker.auditloghandling.AuditLo gDirector] (ForkJoinPool-1-worker-2) [] Correlation ID: null, Call Stack: null, Custom Event ID: -1, Message: VM CentOS7 is down with error. Exit message: Cannot get interface MTU on 'br-int': No such device.
This VM has a nic on ovirtbridge, which comes from the OVN provider.
/Sverker
Den 2016-12-28 kl. 14:38, skrev Marcin Mirecki:
Sverker,
Can you try adding a vnic named veth_* or dummy_*,
(or alternatively add the name of the vnic to
vdsm.config fake_nics), and setup the management
network using this vnic?
I suppose adding the vnic you use for connecting
to the engine to fake_nics should make it visible
to the engine, and you should be able to use it for
the setup.
Marcin
----- Original Message -----
From: "Marcin Mirecki" <mmirecki@redhat.com>
To: "Sverker Abrahamsson" <sverker@abrahamsson.com>
Cc: "Ovirt Users" <users@ovirt.org>
Sent: Wednesday, December 28, 2016 12:06:26 PM
Subject: Re: [ovirt-users] Issue with OVN/OVS and mandatory ovirtmgmt network
I have an internal OVS bridge called ovirtbridge which has a port withI just verified and unfortunately the virtual ports are not visible in engine
IP address, but in the host network settings that port is not visible.
to assign a network to :(
I'm afraid that the engine is not ready for such a scenario (even if it
works).
Please give me some time to look for a solution.
----- Original Message -----
From: "Sverker Abrahamsson" <sverker@abrahamsson.com>______________________________
To: "Marcin Mirecki" <mmirecki@redhat.com>
Cc: "Ovirt Users" <users@ovirt.org>
Sent: Wednesday, December 28, 2016 11:48:24 AM
Subject: Re: [ovirt-users] Issue with OVN/OVS and mandatory ovirtmgmt
network
Hi Marcin
Yes, that is my issue. I don't want to let ovirt/vdsm see eth0 nor
ovsbridge0 since as soon as it sees them it messes up the network config
so that the host will be unreachable.
I have an internal OVS bridge called ovirtbridge which has a port with
IP address, but in the host network settings that port is not visible.
It doesn't help to name it ovirtmgmt.
The engine is able to communicate with the host on the ip it has been
given, it's just that it believes that it HAS to have a ovirtmgmt
network which can't be on OVN.
/Sverker
Den 2016-12-28 kl. 10:45, skrev Marcin Mirecki:
Hi Sverker,
The management network is mandatory on each host. It's used by the
engine to communicate with the host.
Looking at your description and the exception it looks like it is
missing.
The error is caused by not having any network for the host
(network list retrieved in InterfaceDaoImpl.getHostNetworksByCluster -
which
gets all the networks on nics for a host from vds_interface table in the
DB).
Could you maybe create a virtual nic connected to ovsbridge0 (as I
understand you
have no physical nic available) and use this for the management network?
I then create a bridge for use with ovirt, with a private address.I'm not quite sure I understand. Is this yet another bridge connected to
ovsbridge0?
You could also attach the vnic for the management network here if need
be.
Please keep in mind that OVN has no use in setting up the management
network.
The OVN provider can only handle external networks, which can not be used
for a
management network.
Marcin
----- Original Message -----
From: "Sverker Abrahamsson" <sverker@abrahamsson.com>
To: users@ovirt.org
Sent: Wednesday, December 28, 2016 12:39:59 AM
Subject: [ovirt-users] Issue with OVN/OVS and mandatory ovirtmgmt
network
Hi
For long time I've been looking for proper support in ovirt for Open
vSwitch
so I'm happy that it is moving in the right direction. However, there
seems
to still be a dependency on a ovirtmgmt bridge and I'm unable to move
that
to the OVN provider.
The hosting center where I rent hw instances has a bit special network
setup,
so I have one physical network port with a /32 netmask and
point-to-point
config to router. The physical port I connect to a ovs bridge which has
the
public ip. Since ovirt always messes up the network config when I've
tried
to let it have access to the network config for the physical port, I've
set
eht0 and ovsbridge0 as hidden in vdsm.conf.
I then create a bridge for use with ovirt, with a private address. With
the
OVN provider I am now able to import these into the engine and it looks
good. When creating a VM I can select that it will have a vNic on my OVS
bridge.
However, I can't start the VM as an exception is thrown in the log:
2016-12-28 00:13:33,350 ERROR [org.ovirt.engine.core.bll.RunVmCommand]
(default task-5) [3c882d53] Error during ValidateFailure.:
java.lang.NullPointerException
at
org.ovirt.engine.core.bll.scheduling.policyunits.NetworkPoli cyUnit.validateRequiredNetwork sAvailable(NetworkPolicyUnit. java:140)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.policyunits.NetworkPoli cyUnit.filter(NetworkPolicyUni t.java:69)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.SchedulingManager.runIn ternalFilters(SchedulingManage r.java:597)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.SchedulingManager.runFi lters(SchedulingManager.java: 564)
[bll.jar:]
at
org.ovirt.engine.core.bll.scheduling.SchedulingManager.canSc hedule(SchedulingManager.java: 494)
[bll.jar:]
at
org.ovirt.engine.core.bll.validator.RunVmValidator.canRunVm( RunVmValidator.java:133)
[bll.jar:]
at
org.ovirt.engine.core.bll.RunVmCommand.validate(RunVmCommand .java:940)
[bll.jar:]
at
org.ovirt.engine.core.bll.CommandBase.internalValidate(Comma ndBase.java:886)
[bll.jar:]
at
org.ovirt.engine.core.bll.CommandBase.validateOnly(CommandBa se.java:366)
[bll.jar:]
at
org.ovirt.engine.core.bll.PrevalidatingMultipleActionsRunner .canRunActions(PrevalidatingMu ltipleActionsRunner.java:113)
[bll.jar:]
at
org.ovirt.engine.core.bll.PrevalidatingMultipleActionsRunner .invokeCommands(PrevalidatingM ultipleActionsRunner.java:99)
[bll.jar:]
at
org.ovirt.engine.core.bll.PrevalidatingMultipleActionsRunner .execute(PrevalidatingMultiple ActionsRunner.java:76)
[bll.jar:]
at
org.ovirt.engine.core.bll.Backend.runMultipleActionsImpl(Bac kend.java:613)
[bll.jar:]
at
org.ovirt.engine.core.bll.Backend.runMultipleActions(Backend .java:583)
[bll.jar:]
Looking at that section of code where the exception is thrown, I see
that
it
iterates over host networks to find required networks, which I assume is
ovirtmgmt. In the host network setup dialog I don't see any networks at
all
but it lists ovirtmgmt as required. It also list the OVN networks but
these
can't be statically assigned as they are added dynamically when needed,
which is fine.
I believe that I either need to remove ovirtmgmt network or configure
that
it
is provided by the OVN provider, but neither is possible. Preferably it
shouldn't be hardcoded which network is management and mandatory but be
possible to configure.
/Sverker
Den 2016-12-27 kl. 17:10, skrev Marcin Mirecki:
_________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users