2017-05-03 15:09 GMT+01:00 Simone Tiraboschi <stirabos@redhat.com>:

On Wed, May 3, 2017 at 11:30 AM, Manuel Luis Aznar <manuel.luis.aznar@gmail.com> wrote:
Hello Simone and all others,

I have attached to the mail the requested files. If you have any other inquiry just say it, The failed installation drive would be keep safe until solving this problem.

Thanks for all in advance
Manuel

The issue is here:
May 1 11:47:45 host1 journal: libvirt version: 2.0.0, package: 10.el7_3.5 (CentOS BuildSystem <http://bugs.centos.org>, 2017-03-03-02:09:45, c1bm.rdu2.centos.org)
May 1 11:47:45 host1 journal: hostname: host1.bajada.es
May 1 11:47:45 host1 journal: Falló al conectar con el socket de monitor: No existe el proceso
May 1 11:47:45 host1 journal: internal error: process exited while connecting to monitor: /dev/random -device virtio-rng-pci,rng=objrng0,id=rng0,bus=pci.0,addr=0x7 -msg timestamp=on#012Could not access KVM kernel module: Permission denied#012failed to initialize KVM: Permission denied
May 1 11:47:45 host1 journal: libvirt version: 2.0.0, package: 10.el7_3.5 (CentOS BuildSystem <http://bugs.centos.org>, 2017-03-03-02:09:45, c1bm.rdu2.centos.org)
May 1 11:47:45 host1 journal: hostname: host1.bajada.es
May 1 11:47:45 host1 journal: Fin de archivo al leer datos: Error de entrada/salida
May 1 11:47:45 host1 journal: Fin de archivo al leer datos: Error de entrada/salida

could you please also check the permission on /dev/random and SELinux audit logs?

2017-05-02 10:55 GMT+01:00 Simone Tiraboschi <stirabos@redhat.com>:
Sure, but first we need to understand what it's happening: in our CI process everything is fine so I think it's something specific to your env.
Could you please share your:
/var/log/libvirt/qemu/HostedEngine.log
/var/log/messages

thanks,
Simone

On Tue, May 2, 2017 at 11:38 AM, Manuel Luis Aznar <manuel.luis.aznar@gmail.com> wrote:
Ok thankyou.

Suppose that this problem probably would be solve in a future release.

Thanks,
Manuel

2017-05-02 10:35 GMT+01:00 Simone Tiraboschi <stirabos@redhat.com>:

On Tue, May 2, 2017 at 11:30 AM, Manuel Luis Aznar <manuel.luis.aznar@gmail.com> wrote:
Hello there again,

Yes as I say, I have done several clean installations and the VM engine sometimes starts without any problem. So Simone any recommendation to make the engine VM starts properly?¿

While is installing the HA agent and HA broker are down, would I get good result by starting the services myself?¿

Any help from Simone or somebody would be appreciated
Thanks for all in advance
Manuel Luis Aznar

I suggest to check libvirt logs.

2017-05-02 7:54 GMT+01:00 Simone Tiraboschi <stirabos@redhat.com>:

On Mon, May 1, 2017 at 3:14 PM, Manuel Luis Aznar <manuel.luis.aznar@gmail.com> wrote:
Hello there,

I have been looking in the internet using google why my installation of ovirt-hosted-engine is failing.

I have found this link:

https://www.mail-archive.com/users@ovirt.org/msg40864.html (Hosted engine install failed; vdsm upset about broker)

It seems to be the same error...

So to knarra and Jamie Lawrence my question is:

Did you manage to discover the problem?? In my instalation I am using nfs and not gluster...

I have read the error and is the same error "BrokerConnectionError: ...". The ovirt-ha-agent and ovirt-ha-broker did not start when the installation is creating the engine VM...

This is just a false positive: the HA agent and the HA broker are still down so vdsm is complaining but at that point it's absolutely fine by itself since the engine VM still doesn't exists.
We already have an open bug to reduce the impact of that message.

The real issue is that for some reason the engine VM could not start on your system.

As I have said before any help would be very appreciated...no matter whom will give it
Thanks for all in advance
Manuel Luis Aznar

2017-05-01 12:21 GMT+01:00 Manuel Luis Aznar <manuel.luis.aznar@gmail.com>:
Hello Simone and all the comunity,

I have been doing the instalation of ovirt hosted engine again and it fails, libvirtd and vdsmd services are failing. They are failing with the following errors:

libvirt daemon

libvirtd.service - Virtualization daemon
Loaded: loaded (/usr/lib/systemd/system/libvirtd.service; enabled; vendor preset: enabled)
Drop-In: /etc/systemd/system/libvirtd.service.d
ââunlimited-core.conf
Active: active (running) since lun 2017-05-01 11:43:49 WEST; 14min ago
Docs: man:libvirtd(8)
http://libvirt.org
Main PID: 21993 (libvirtd)
CGroup: /system.slice/libvirtd.service
ââ21993 /usr/sbin/libvirtd --listen

may 01 11:43:49 host1.bajada.es systemd[1]: Starting Virtualization daemon...
may 01 11:43:49 host1.bajada.es systemd[1]: Started Virtualization daemon.
may 01 11:47:45 host1.bajada.es libvirtd[21993]: libvirt version: 2.0.0, package: 10.el7_3.5 (CentOS BuildSystem <http://bugs.centos.org>, 2017-03-03-02:09:45, c1bm.rdu2.centos.org)
may 01 11:47:45 host1.bajada.es libvirtd[21993]: hostname: host1.bajada.es
may 01 11:47:45 host1.bajada.es libvirtd[21993]: FallÃ³ al conectar con el socket de monitor: No existe el proceso
may 01 11:47:45 host1.bajada.es libvirtd[21993]: internal error: process exited while connecting to monitor: /dev/random -device virtio-rng-pci,rng=objrng0,id=rng0,bus=pci.0,addr=0x7 -msg timestamp=on
Could not access KVM kernel module: Permission denied
failed to initialize KVM: Permission denied

vdsm daemon

vdsmd.service - Virtual Desktop Server Manager
Loaded: loaded (/usr/lib/systemd/system/vdsmd.service; enabled; vendor preset: enabled)
Active: active (running) since lun 2017-05-01 11:43:51 WEST; 15min ago
Main PID: 22119 (vdsm)
CGroup: /system.slice/vdsmd.service
ââ22119 /usr/bin/python2 /usr/share/vdsm/vdsm
ââ22612 /usr/libexec/ioprocess --read-pipe-fd 68 --write-pipe-fd 67 --max-threads 10 --max-queued-requests 10
ââ22630 /usr/libexec/ioprocess --read-pipe-fd 76 --write-pipe-fd 75 --max-threads 10 --max-queued-requests 10
ââ22887 /usr/libexec/ioprocess --read-pipe-fd 44 --write-pipe-fd 43 --max-threads 10 --max-queued-requests 10
ââ22893 /usr/libexec/ioprocess --read-pipe-fd 52 --write-pipe-fd 50 --max-threads 10 --max-queued-requests 10

may 01 11:58:37 host1.bajada.es vdsm[22119]: vdsm ovirt_hosted_engine_ha.lib.brokerlink.BrokerLink ERROR Failed to connect to broker, the number of errors has exceeded the limit (1)
may 01 11:58:37 host1.bajada.es vdsm[22119]: vdsm root ERROR failed to retrieve Hosted Engine HA info
Traceback (most recent call last):
File "/usr/lib/python2.7/site-packages/vdsm/host/api.py", line 231, in _getHaInfo
stats = instance.get_all_stats()
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/client/client.py", line 102, in get_all_stats
with broker.connection(self._retries, self._wait):
File "/usr/lib64/python2.7/contextlib.py", line 17, in __enter__
return self.gen.next()
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/lib/brokerlink.py", line 99, in connection
self.connect(retries, wait)
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/lib/brokerlink.py", line 78, in connect
raise BrokerConnectionError(error_msg)
BrokerConnectionError: Failed to connect to broker, the number of errors has exceeded the limit (1)
may 01 11:58:52 host1.bajada.es vdsm[22119]: vdsm ovirt_hosted_engine_ha.lib.brokerlink.BrokerLink ERROR Failed to connect to broker, the number of errors has exceeded the limit (1)

I have been looking to the ovirt mailing list (and also internet looking up in google) but I dont get what is the problem.

I have attached to the mail the vdsm, ovirt-hosted-engine-setup and the answer of the installation. In the vdsm.log I got the following error:

libvirtError: internal error: process exited while connecting to monitor: /dev/random -device virtio-rng-pci,rng=objrng0,id=rng0,bus=pci.0,addr=0x7 -msg timestamp=on
Could not access KVM kernel module: Permission denied
failed to initialize KVM: Permission denied

I have been looking for that error but I dont get anything clear, so I will greatly appreciate the help of somebody...

The KVM modules are loaded because if I fired up this "lsmod | grep kvm" I get the following:

kvm_intel 170181 0
kvm 554609 1 kvm_intel
irqbypass 13503 1 kvm

Also the group owner of /dev/kvm is:

crw-rw-rw-+ 1 root kvm 10, 232 may 1 01:26 /dev/kvm

Hope somebody could help
Thanks for all in advance
Manuel Luis Aznar

2017-03-15 11:58 GMT+00:00 Manuel Luis Aznar <manuel.luis.aznar@gmail.com>:
Hello there again,

Yes that is correct. I interrupted the setup with Ctrl+C. That was because while I was answering, at the same time, I was looking at this file, and I saw this:

FAILED: conflicting vdsm and libvirt-qemu tls configuration.
vdsm.conf with ssl=True requires the following changes:
libvirtd.conf: listen_tcp=0, auth_tcp="sasl", listen_tls=1
qemu.conf: spice_tls=1.

So I decided to interrupt the installation, because of the error, edit the files (vdsm.conf and qemu.conf) and then I executed the installation again and it was successful. It seams that the change of the values in that files, in my case, produced a successful instalation.

Sorry if my english is hard to understand, now you understand what I did.

Any question, remark just go ahead

Thanks,
Manuel

2017-03-15 11:22 GMT+00:00 Simone Tiraboschi <stirabos@redhat.com>:

On Wed, Mar 15, 2017 at 12:17 PM, Manuel Luis Aznar <manuel.luis.aznar@gmail.com> wrote:
Hello Simone,

The quoted lines on your last message are on lines 1238-1245 on the attached log ovirt-hosted-engine-setup file.

That file is the first hosted-engine setup. But this log file is not the result of a host-engine-setup file. I start with the installation and while I was answering the question I was looking to this log file for errors and when I found this errors I stopped and done this:

FAILED: conflicting vdsm and libvirt-qemu tls configuration.
vdsm.conf with ssl=True requires the following changes:
libvirtd.conf: listen_tcp=0, auth_tcp="sasl", listen_tls=1
qemu.conf: spice_tls=1.

Previously to this installation I have done several installations without revising this log file and always getting failed installations.

Please its important to note that:

The currently setup which we are talking about was using repo "ovirt-release41-pre.rpm". After correcting that two files I do the installation and in the end it was completed successfully.

When I have some time I will try to install again using the realease repo "ovirt-release41.rpm"

If you have any explanation, question or remark, please go ahead...

From the attached logs it seams that you voluntary interrupted the setup from keyboard here:
2017-03-07 11:23:17 DEBUG otopi.plugins.otopi.dialog.human dialog.__logString:204 DIALOG:SEND iptables was detected on your computer, do you wish setup to configure it? (Yes, No)[Yes]:
2017-03-07 12:06:15 DEBUG otopi.context context._executeMethod:142 method exception
Traceback (most recent call last):
File "/usr/lib/python2.7/site-packages/otopi/context.py", line 132, in _executeMethod
method['method']()
File "/usr/share/ovirt-hosted-engine-setup/scripts/../plugins/gr-he-setup/network/firewall_manager.py", line 157, in _customization
default=_('Yes'),
File "/usr/share/otopi/plugins/otopi/dialog/human.py", line 177, in queryString
value = self._readline(hidden=hidden)
File "/usr/lib/python2.7/site-packages/otopi/dialog.py", line 246, in _readline
value = self.__input.readline()
File "/usr/lib/python2.7/site-packages/otopi/main.py", line 53, in _signal
raise RuntimeError("SIG%s" % signum)
RuntimeError: SIG2

I will report back.
Thanks for all in advance
Manuel

2017-03-13 17:29 GMT+00:00 Simone Tiraboschi <stirabos@redhat.com>:

On Mon, Mar 13, 2017 at 4:08 PM, Manuel Luis Aznar <manuel.luis.aznar@gmail.com> wrote:
Hello to all there again,

I was having some troubles while installing ovirt Hosted Engine, I took some look at the hosted engine setup logs while I was running the hosted-engine --deploy and I found the following in the ovirt hosted engine setup logs:

lvm requires configuration
libvirt is not configured for vdsm yet
FAILED: conflicting vdsm and libvirt-qemu tls configuration.
vdsm.conf with ssl=True requires the following changes:
libvirtd.conf: listen_tcp=0, auth_tcp="sasl", listen_tls=1
qemu.conf: spice_tls=1.

hosted-engine setup is already running vdsm-tool configure --force so it should configure libvirt and qemu for you, not sure why it failed.
Could you please attach the logs from the failed hosted-engine-setup run?

When I saw this I stopped the setup and edited this two files (vdsm.conf and qemu.conf) set the stated configurations and run the deploy again. All was fine and I dont have any trouble the installation finished successfully. This was using ovirt-release41-pre.rpm repo.

I will be trying the same installation with ovirt-release41.rpm (when I have time) and I will report what happened.

Thanks for all
Manuel Luis Aznar

2017-03-06 1:31 GMT+00:00 Manuel Luis Aznar <manuel.luis.aznar@gmail.com>:
Hey there,

I have been loking around, of course as of now the following I am going to say I suppose is not anything new to you:

This is the status of libvirtd:

â libvirtd.service - Virtualization daemon
Loaded: loaded (/usr/lib/systemd/system/libvirtd.service; enabled; vendor preset: enabled)
Drop-In: /etc/systemd/system/libvirtd.service.d
ââunlimited-core.conf
Active: active (running) since lun 2017-03-06 01:25:05 WET; 1min 37s ago
Docs: man:libvirtd(8)
http://libvirt.org
Main PID: 24350 (libvirtd)
CGroup: /system.slice/libvirtd.service
ââ24350 /usr/sbin/libvirtd --listen

mar 06 01:25:05 host1.bajada.es systemd[1]: Starting Virtualization daemon...
mar 06 01:25:05 host1.bajada.es systemd[1]: Started Virtualization daemon.

After looking at the state I fire up the VM engine with the command "hosted-engine --vm-start" and I got the following:

VM exists and is down, destroying it
Machine destroyed

ed786811-0321-431e-be4b-2d03764c1b02
Status = WaitForLaunch
nicModel = rtl8139,pv
statusTime = 4374100040
emulatedMachine = pc
pid = 0
vmName = HostedEngine
devices = [{'index': '2', 'iface': 'ide', 'specParams': {}, 'readonly': 'true', 'deviceId': '506df4eb-e783-4451-a8a6-993fa4dbb381', 'address': {'bus': '1', 'controller': '0', 'type': 'drive', 'target': '0', 'unit': '0'}, 'device': 'cdrom', 'shared': 'false', 'path': '', 'type': 'disk'}, {'index': '0', 'iface': 'virtio', 'format': 'raw', 'bootOrder': '1', 'poolID': '00000000-0000-0000-0000-000000000000', 'volumeID': '2bc39472-1a4b-4c7d-8ef9-1212182ad802', 'imageID': '08288fcf-6b12-4bd1-84d3-259992e7aa6d', 'specParams': {}, 'readonly': 'false', 'domainID': 'f44afe8d-56f9-4e1e-beee-4daa548dbad8', 'optional': 'false', 'deviceId': '08288fcf-6b12-4bd1-84d3-259992e7aa6d', 'address': {'slot': '0x06', 'bus': '0x00', 'domain': '0x0000', 'type': 'pci', 'function': '0x0'}, 'device': 'disk', 'shared': 'exclusive', 'propagateErrors': 'off', 'type': 'disk'}, {'device': 'scsi', 'model': 'virtio-scsi', 'type': 'controller'}, {'nicModel': 'pv', 'macAddr': '00:16:3e:65:a6:4e', 'linkActive': 'true', 'network': 'ovirtmgmt', 'specParams': {}, 'deviceId': '84b82c6c-bcca-4983-82d5-8d1e3ab3811a', 'address': {'slot': '0x03', 'bus': '0x00', 'domain': '0x0000', 'type': 'pci', 'function': '0x0'}, 'device': 'bridge', 'type': 'interface'}, {'device': 'console', 'specParams': {}, 'type': 'console', 'deviceId': '6236af73-8dab-4d14-b950-fb4ad01d4420', 'alias': 'console0'}, {'device': 'vga', 'alias': 'video0', 'type': 'video'}, {'device': 'virtio', 'specParams': {'source': 'random'}, 'model': 'virtio', 'type': 'rng'}]
guestDiskMapping = {}
vmType = kvm
clientIp =
displaySecurePort = -1
memSize = 4096
displayPort = -1
cpuType = Broadwell
spiceSecureChannels = smain,sdisplay,sinputs,scursor,splayback,srecord,ssmartcard,susbredir
smp = 2
displayIp = 0
display = vnc
maxVCpus = 6

After that if I look again at the status of libvirtd I obtain:

â libvirtd.service - Virtualization daemon
Loaded: loaded (/usr/lib/systemd/system/libvirtd.service; enabled; vendor preset: enabled)
Drop-In: /etc/systemd/system/libvirtd.service.d
ââunlimited-core.conf
Active: active (running) since lun 2017-03-06 01:25:05 WET; 5min ago
Docs: man:libvirtd(8)
http://libvirt.org
Main PID: 24350 (libvirtd)
CGroup: /system.slice/libvirtd.service
ââ24350 /usr/sbin/libvirtd --listen

mar 06 01:25:05 host1.bajada.es systemd[1]: Starting Virtualization daemon...
mar 06 01:25:05 host1.bajada.es systemd[1]: Started Virtualization daemon.
mar 06 01:29:39 host1.bajada.es libvirtd[24350]: libvirt version: 2.0.0, package: 10.el7_3.5 (CentOS BuildSystem <http://bugs.centos.org>, 2017-03-03-02:09:45, c1bm.rdu2.centos.org)
mar 06 01:29:39 host1.bajada.es libvirtd[24350]: hostname: host1.bajada.es
mar 06 01:29:39 host1.bajada.es libvirtd[24350]: FallÃ³ al conectar con el socket de monitor: No existe el proceso
mar 06 01:29:39 host1.bajada.es libvirtd[24350]: internal error: process exited while connecting to monitor: Could not access KVM kernel module: Permission denied
failed to initialize KVM: Permission denied

So the libvirtd is the problem, as i said this is nothing new to you of course...

Thanks again for any help
Manuel

2017-03-05 18:51 GMT+00:00 Manuel Luis Aznar <manuel.luis.aznar@gmail.com>:
Hey there again,

Can you check if you have KVM modules loaded?

In order to check that I fire up the following command: "lsmod | grep kvm"

Result was:

kvm_intel 170181 0
kvm 554609 1 kvm_intel
irqbypass 13503 1 kvm

Also check group owner for "/dev/kvm". I fire this: "ls -la /dev/kvm". The result was:

crw-rw-rw-+ 1 root kvm 10, 232 mar 5 03:35 /dev/kvm

Also I check if there were some remain packages pending to install for kvm and qemu and I got:

yum install \*kvm\*

The result is, that the system need to install the following:

Instalando:
centos-release-qemu-ev noarch 1.0-1.el7 extras 11 k
qemu-guest-agent x86_64 10:2.5.0-3.el7 base 133 k
qemu-kvm-ev-debuginfo x86_64 10:2.6.0-28.el7_3.3.1 ovirt-4.0 12 M
vdsm-hook-faqemu noarch 4.18.21-1.el7.centos ovirt-4.0 15 k
vdsm-hook-qemucmdline noarch 4.18.21-1.el7.centos ovirt-4.0 11 k
Instalando para las dependencias:
centos-release-virt-common noarch 1-1.el7.centos extras 4.5 k

Checking libvirtd service status I got:

libvirtd.service - Virtualization daemon
Loaded: loaded (/usr/lib/systemd/system/libvirtd.service; enabled; vendor preset: enabled)
Drop-In: /etc/systemd/system/libvirtd.service.d
ââunlimited-core.conf
Active: active (running) since dom 2017-03-05 15:56:11 WET; 2h 51min ago
Docs: man:libvirtd(8)
http://libvirt.org
Main PID: 19415 (libvirtd)
CGroup: /system.slice/libvirtd.service
19415 /usr/sbin/libvirtd --listen

mar 05 15:56:10 host1.bajada.es systemd[1]: Starting Virtualization daemon...
mar 05 15:56:11 host1.bajada.es systemd[1]: Started Virtualization daemon.
mar 05 16:00:04 host1.bajada.es libvirtd[19415]: libvirt version: 2.0.0, package: 10.el7_3.5 (CentOS BuildSystem <http://bugs.centos.org>, 2017-03-03-02:09:45, c1bm.rdu2.centos.org)
mar 05 16:00:04 host1.bajada.es libvirtd[19415]: hostname: host1.bajada.es
mar 05 16:00:04 host1.bajada.es libvirtd[19415]: Failed to connect to the socket monitor: process does not exits
(Fallo al conectar con el socket de monitor: No existe el proceso)
mar 05 16:00:04 host1.bajada.es libvirtd[19415]: internal error: process exited while connecting to monitor: Could not access KVM kernel module: Permission denied
failed to initialize KVM: Permission denied

Thanks for all in advance
I will be waiting for you. Any help appreciated
Manuel

2017-03-05 17:33 GMT+00:00 Artyom Lukianov <alukiano@redhat.com>:
I found this one under the vdsm log:
libvirtError: internal error: process exited while connecting to monitor: Could not access KVM kernel module: Permission denied
failed to initialize KVM: Permission denied
Thread-70::INFO::2017-03-05 16:00:04,325::vm::1330::virt.vm::(setDownStatus) vmId=`ed786811-0321-431e-be4b-2d03764c1b02`::Changed state to Down: internal error: process exited while connecting to monitor: Could not access KVM kernel module: Permission denied
failed to initialize KVM: Permission denied (code=1)
Thread-70::INFO::2017-03-05 16:00:04,325::guestagent::430::virt.vm::(stop) vmId=`ed786811-0321-431e-be4b-2d03764c1b02`::Stopping connection
Thread-70::DEBUG::2017-03-05 16:00:04,325::vmchannels::238::vds::(unregister) Delete fileno 52 from listener.
Thread-70::DEBUG::2017-03-05 16:00:04,325::vmchannels::66::vds::(_unregister_fd) Failed to unregister FD from epoll (ENOENT): 52
Thread-70::DEBUG::2017-03-05 16:00:04,326::__init__::209::jsonrpc.Notification::(emit) Sending event {"params": {"ed786811-0321-431e-be4b-2d03764c1b02": {"status": "Down", "exitReason": 1, "exitMessage": "internal error: process exited while connecting to monitor: Could not access KVM kernel module: Permission denied\nfailed to initialize KVM: Permission denied", "exitCode": 1}, "notify_time": 4339924730}, "jsonrpc": "2.0", "method": "|virt|VM_status|ed786811-0321-431e-be4b-2d03764c1b02"}

Can you check if you have KVM modules loaded? Also, check group owner for "/dev/kvm".
Best Regards

On Sat, Mar 4, 2017 at 4:24 PM, Manuel Luis Aznar <manuel.luis.aznar@gmail.com> wrote:
Hello there again,

The error on the first email was using the repo ovirt-release41.rpm (http://resources.ovirt.org/pub/yum-repo/ovirt-release41.rpm), so as I were getting the same error again and again I am currently trying with ovirt-release41-snapshot.rpm (http://resources.ovirt.org/pub/yum-repo/ovirt-release41-snapshot.rpm) and the result is nearly the same.

After creating the VM on the installation I got the same error with the command "systemctl status vdsmd":

mar 04 14:10:19 host1.bajada.es vdsm[20443]: vdsm root ERROR failed to retrieve Hosted Engine HA info

Traceback (most recent call last):
File "/usr/lib/python2.7/site-packages/vdsm/host/api.py", line 231, in _getHaInfo
stats = instance.get_all_stats()
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/client/client.py", line 102, in get_all_stats
with broker.connection(self._retries, self._wait):
File "/usr/lib64/python2.7/contextlib.py", line 17, in __enter__
return self.gen.next()
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/lib/brokerlink.py", line 99, in connection
self.connect(retries, wait)
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/lib/brokerlink.py", line 78, in connect
raise BrokerConnectionError(error_msg)
BrokerConnectionError: Failed to connect to broker, the number of errors has exceeded the limit (1)

mar 04 14:10:34 host1.bajada.es vdsm[20443]: vdsm ovirt_hosted_engine_ha.lib.brokerlink.BrokerLink ERROR Failed to connect to broker, the number of errors has exceeded the limit (1)

I have noticed that the ovirt-ha-agent and ovirt-ha-broker services was not running. I guess if this have something to do with the error in vsmd service log.

But in this case the ovirt-hosted-engine-installation prints the vnc connection and I can connect to the engine VM.

Thanks for all in advance
Any help would be appreciated
Manuel Luis Aznar

2017-03-03 21:48 GMT+00:00 Manuel Luis Aznar <manuel.luis.aznar@gmail.com>:
Hello there,

I am having some trouble when deploying an oVirt 4.1 hosted engine installation.

When I m just to end the installation and the hosted engine setup script is about to start the Vm engine (appliance) it fails saying "The VM is not powring up".

If I double check the service vdsmd i get this error all the time:

vdsm root ERROR failed to retrieve Hosted Engine HA info
Traceback (most recent call last):
File "/usr/lib/python2.7/site-packages/vdsm/host/api.py", line 231, in _getHaInfo
stats = instance.get_all_stats()
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/client/client.py", line 102, in get_all_stats
with broker.connection(self._retries, self._wait):
File "/usr/lib64/python2.7/contextlib.py", line 17, in __enter__
return self.gen.next()
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/lib/brokerlink.py", line 99, in connection
self.connect(retries, wait)
File "/usr/lib/python2.7/site-packages/ovirt_hosted_engine_ha/lib/brokerlink.py", line 78, in connect
raise BrokerConnectionError(error_msg)
BrokerConnectionError: Failed to connect to broker, the number of errors has exceeded the limit (1)

Did anyone have experimented the same problem?¿? Any hint on How to solved it?¿? I have tried several times with clean installations and always getting the same...

The host where I am trying to do the installation have CentOS 7...

Thanks for all in advance
Will be waiting for any hint to see what I am doing wrong...
Manuel Luis Aznar

_______________________________________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users

_______________________________________________
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users