[Users] Testing ovirt all in one on F18 gives error on DB creation

[Gianluca Cecchi]

On Wed, Dec 12, 2012 at 11:29 PM, Jason Brooks wrote:

>
> > > > > the same if I run from command line:
> > > > > /sbin/tuned-adm profile virtual-host
> > >
> > >
> > > I was having this same issue w/ F18 w/ all updates applied and
> > > ovirt
> > > 3.2 from the new 3.2-alpha repo. I did a "yum downgrade tuned" and
> > > the install completed successfully.
> > >
> > > Now I just have to figure out why my host is non-operational...
> > >
> > > Jason
> >
> > I suggest you perform host deployment again.
>
> Thanks, that worked. The ovirtmgmt bridge wasn't created the first time
> around, now I'm up.
>
>
Hello,  had again time to come back on this today.
So I updated my f18 vm with ovirt-nightly repo and then engine-cleanup and
engine-setup again.
and I got the usual error on timeout when first deploying host.

But I'm able to connect from my host to webadmin portal on my vm (f18aio)

After downgrade of tuned-adm it worked for me too the re-deploy of the host
from the gui.

from
Dec 11 00:58:09 Updated: tuned-2.1.1-1.fc18.noarch

to
Dec 18 13:00:14 Installed: tuned-2.0.1-4.fc18.noarch

I think it was the deploy step that caused also the vm (oVirt node deployed
from itself...) to restart.
And now I have this situation I would like to fix:

my vm is f18aio with ip 192.1681.122.160
On my f17 host I have in /etc/hosts
192.168.122.160 f18aio.localdomain.local f18aio

so that dnsmask lets me use firefox on host to connect to webadmin portal
on vm
But after the successful deploy I'm not able anymore to connect correctly
as before to admin portal....

>From host:

http://f18aio ---> ok

click on webadmin portal link --->  ko
Firefox can't establish a connection to the server at f18aio.

http://192.168.122.160 --> ko
Firefox can't establish a connection to the server at 192.168.122.160

If I ssh -X f18aio from host and run firefox on vm side:

http://f18aio ---> ok

click on webadmin portal link --->  ok
(see screenshot at
https://docs.google.com/open?id=0BwoPbcrMv8mvZzdsQnFMU0RuUGs
)

The same if I use 192.168.122.160


DO I have to set up anything at vm side of my host side?
At this moment on it I see I have the ip address put on ovirtmgmt network
that the deploy step made available:

[g.cecchi at f18aio ~]$ ip addr list
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master
ovirtmgmt state UP qlen 1000
    link/ether 52:54:00:b0:6c:5f brd ff:ff:ff:ff:ff:ff
    inet6 fe80::5054:ff:feb0:6c5f/64 scope link
       valid_lft forever preferred_lft forever
3: ovirtmgmt: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UP
    link/ether 52:54:00:b0:6c:5f brd ff:ff:ff:ff:ff:ff
    inet 192.168.122.160/24 brd 192.168.122.255 scope global ovirtmgmt
    inet6 fe80::5054:ff:feb0:6c5f/64 scope link
       valid_lft forever preferred_lft forever
5: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
    link/ether 06:95:56:60:84:1a brd ff:ff:ff:ff:ff:ff
6: bond0: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue
state DOWN
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
7: bond4: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue
state DOWN
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff

[g.cecchi at f18aio ~]$ cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: load balancing (round-robin)
MII Status: down
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0

[g.cecchi at f18aio ~]$ cat /proc/net/bonding/bond4
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: load balancing (round-robin)
MII Status: down
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0

[root at f18aio ~]# brctl show
bridge name bridge id STP enabled interfaces
;vdsmdummy; 8000.000000000000 no
ovirtmgmt 8000.525400b06c5f no eth0


Thanks in advance,
Gianluca
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20121218/33aa76da/attachment-0001.html>