[Users] Creating Logical Network issue - API

[Moti Asayag]

----- Original Message -----
> From: "Tejesh M" <tejeshmk at gmail.com>
> To: "Moti Asayag" <masayag at redhat.com>
> Cc: "users at oVirt.org" <users at ovirt.org>
> Sent: Monday, February 24, 2014 1:18:53 PM
> Subject: Re: [Users] Creating Logical Network issue - API
> 
> The example updates the existing Network (i.e. if the Logical Network is
> already mapped to eth1). But what i'm looking for is how to map Logical
> Network "ApiNetWork" to "eth1", please refer screenshot.
> 

There is an example of the 'setup networks' api usage via the java sdk in [1]
which is the recommended api for configuring host networking.

[1] https://motiasayag.wordpress.com/2014/02/24/invoke-setup-networks-from-the-java-sdk/

> 
> On Mon, Feb 24, 2014 at 4:11 PM, Moti Asayag <masayag at redhat.com> wrote:
> 
> > ----- Original Message -----
> > > From: "Tejesh M" <tejeshmk at gmail.com>
> > > To: "Moti Asayag" <masayag at redhat.com>
> > > Cc: "users at oVirt.org" <users at ovirt.org>
> > > Sent: Monday, February 24, 2014 11:59:42 AM
> > > Subject: Re: [Users] Creating Logical Network issue - API
> > >
> > > While setting Logical Network, it fails with below error:
> > > code  : 400
> > > reason: Bad Request
> > > detail: Previous network name is required.
> >
> > See an example in the following post:
> >
> >
> > https://motiasayag.wordpress.com/2014/02/24/network-configuration-using-ovirt-engine-java-sdk/
> >
> > >
> > > Code:
> > >           String nw_name="ApiNetWork";
> > >           org.ovirt.engine.sdk.decorators.Host hst =
> > > api.getHosts().get("rhevhost");
> > >
> > > hst.getHostNics().get("eth1").setNetwork(api.getNetworks().get(nw_name));
> > >           //hst.getHostNics().get("eth1").setCheckConnectivity(true);
> > >           //hst.getHostNics().get("eth1").setOverrideConfiguration(true);
> > >           hst.getHostNics().get("eth1").update();
> > >
> > >
> > >
> > > On Mon, Feb 24, 2014 at 2:30 PM, Tejesh M <tejeshmk at gmail.com> wrote:
> > >
> > > > Can you tel me how do i assign Logical Network(s) to one of the
> > Physical
> > > > Nic on the Host.
> > > >
> > > >
> > > > On Fri, Feb 21, 2014 at 1:37 PM, Moti Asayag <masayag at redhat.com>
> > wrote:
> > > >
> > > >> h
> > > >>
> > > >> ----- Original Message -----
> > > >> > From: "Tejesh M" <tejeshmk at gmail.com>
> > > >> > To: "users at oVirt.org" <users at ovirt.org>
> > > >> > Sent: Thursday, February 20, 2014 11:48:56 AM
> > > >> > Subject: [Users] Creating Logical Network issue - API
> > > >> >
> > > >> > Hi ,
> > > >> >
> > > >> > I'm trying to create Logical Network and assign it to cluster &
> > want to
> > > >> bond
> > > >> > this to one of the Network Interface on Host. so that i can isolate
> > my
> > > >> VM
> > > >> > from other networks.
> > > >> >
> > > >> > The issue is even if i set Cluster while creating Logical Network,
> > it
> > > >> is not
> > > >> > setting the cluster. In Web Admin it is in unset state.
> > > >> >
> > > >> > Also, let me know how do i bind this Logical network on Host
> > Interface.
> > > >> >
> > > >> > Java code:
> > > >> >
> > > >> > Network nw1=new Network();
> > > >> > VLAN vlan = new VLAN();
> > > >> > vlan.setId(2000);
> > > >> > nw1.setVlan(vlan);
> > > >> > IP ip = new IP();
> > > >> > ip.setAddress("192.168.1.151");
> > > >> > ip.setGateway("192.168.1.1");
> > > >> > ip.setNetmask("255.255.255.0");
> > > >>
> > > >> Note that the stated IP above will not be used to set the address on
> > the
> > > >> host itself.
> > > >> In order to do so you should use either the 'setup networks' api on
> > > >> host's nics level.
> > > >> (Alternately, you can send POST request to /hosts/{host:id}/nics which
> > > >> utilize the
> > > >> former api (it is a bit simpler than using the setup networks api).
> > > >>
> > > >> Should look like:
> > > >>     Host host = api.getHosts().get("host_name");
> > > >>     Action action = new Action();
> > > >>     action.setCheckConnectivity(true); //required for rollback in
> > case of
> > > >> configuration failure
> > > >>     action.setHostNics(...); // should contain the target
> > configuration
> > > >>     host.getHostNics().setupnetworks(action);
> > > >>
> > > >> where the action should contain the entire desired network
> > configuration.
> > > >>
> > > >> You can find various python-sdk example for setup networks on my blog
> > [1]
> > > >> I'll post few examples using the java sdk earlier next week.
> > > >>
> > > >> [1] https://motiasayag.wordpress.com/
> > > >>
> > > >> > nw1.setIp(ip);
> > > >> > nw1.setName("apiNetwork");
> > > >> >
> > > >> > nw1.setDataCenter(api.getDataCenters().get("testDC"));
> > > >> > nw1.setCluster(api.getClusters().get("testCluster"));
> > > >> >
> > > >> > org.ovirt.engine.sdk.decorators.Network nw2 =
> > > >> api.getNetworks().add(nw1);
> > > >> >
> > > >> > --
> > > >> > Thanks & Regards
> > > >> > Tejesh
> > > >> >
> > > >> > _______________________________________________
> > > >> > Users mailing list
> > > >> > Users at ovirt.org
> > > >> > http://lists.ovirt.org/mailman/listinfo/users
> > > >> >
> > > >>
> > > >
> > > >
> > > >
> > > > --
> > > > Thanks & Regards
> > > > Tejesh
> > > >
> > >
> > >
> > >
> > > --
> > > Thanks & Regards
> > > Tejesh
> > >
> >
> 
> 
> 
> --
> Thanks & Regards
> Tejesh
>