[ovirt-users] Modules sanlock are not configured

[Bloemen, Jurriën]

Hi all,

First of all thanks Yaniv for your reply!

This is a fresh new installed system. It was not registered to another
oVirt engine before.

So...

The output of "groups sanlock² is
sanlock : sanlock disk qemu

KVM is missing. There is no kvm group at all or user for that matter!?

I ran the command "vdsm-tool configure --module sanlock ‹force² and after
that ³groups sanlock² but it shows the same output as above.

Do you have other ideas what to check?

Thanks in advance,

Jurriën

On 31/03/15 10:23, "ybronhei" <ybronhei at redhat.com> wrote:

>Hey guys,
>
>Probably the problem is that sanlock service cannot stop properly - was
>the host registered to another ovirt engine before and you missed to put
>it on maintenance before adding it to another system?
>
>Such issue raised before when sanlock service fails to stop - can you
>explicitly check if does - service sanlock stop - fail or pass?
>
>If it fails it means that some leases are still locked and reboot will
>solve the issue.
>
>If that is not the case please share the output of "groups sanlock" - it
>should be  - sanlock : sanlock disk kvm qemu after the call to -
>vdsm-tool configure --module sanlock --force (fyi all this configure
>call does is to add sanlock user to those groups in this case)
>
>Hope the information helps. Please share your progress with the issue.
>
>Yaniv Bronhaim.
>
>On 03/31/2015 10:15 AM, Bloemen, Jurriën wrote:
>> I did that also. I forgot to mention it because you only have to run
>>--force if you didn¹t stop the sanlock process of running.
>> The result of with and without is the same. Still the vdsmd process
>>cannot start.
>>
>>
>>
>> From: Roy Golan <rgolan at redhat.com<mailto:rgolan at redhat.com>>
>> Date: Monday 30 March 2015 23:25
>> To: Jurriën Bloemen
>><jurrien.bloemen at dmc.amcnetworks.com<mailto:jurrien.bloemen at dmc.amcnetwor
>>ks.com>>
>> Cc: "users at ovirt.org<mailto:users at ovirt.org>"
>><users at ovirt.org<mailto:users at ovirt.org>>
>> Subject: Re: [ovirt-users] Modules sanlock are not configured
>>
>>
>> On Mar 30, 2015 10:45 PM, Jurriën
>><Jurrien.Bloemen at dmc.amcnetworks.com<mailto:Jurrien.Bloemen at dmc.amcnetwor
>>ks.com>> wrote:
>>>
>>> Hi all,
>>>
>>> I have CentOS 7 running and I added the oVirt 3.5 repo to it. I open
>>>the oVirt Manager and added a new system to it.
>>> The manager says installing and after that is fails to connect.
>>>Looking on the system I see:
>>>
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: Running mkdirs
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: Running
>>>configure_coredump
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: Running
>>>configure_vdsm_logs
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: Running
>>>wait_for_network
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: Running
>>>run_init_hooks
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: Running
>>>upgraded_version_check
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: Running
>>>check_is_configured
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: Error:
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: One of the modules is not
>>>configured to work with VDSM.
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: To configure the module
>>>use the following:
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: 'vdsm-tool configure
>>>[--module module-name]'.
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: If all modules are not
>>>configured try to use:
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: 'vdsm-tool configure
>>>--force'
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: (The force flag will stop
>>>the module's service and start it
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: afterwards automatically
>>>to load the new configuration.)
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: libvirt is already
>>>configured for vdsm
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: Modules sanlock are not
>>>configured
>>> Mar 30 21:09:37 vdsmd_init_common.sh[7106]: vdsm: stopped during
>>>execute check_is_configured task (task returned with error code 1).
>>>
>>> So I run vdsm-tool configure after I stop sanlock.
>>>
>>> # vdsm-tool configure
>>
>> Try adding --force (this is what the log suggests)
>>
>>>
>>> Checking configuration status...
>>>
>>> libvirt is already configured for vdsm
>>> SUCCESS: ssl configured to true. No conflicts
>>>
>>> Running configure...
>>> Reconfiguration of sanlock is done.
>>>
>>> Done configuring modules to VDSM.
>>>
>>> But when I want to start vdsmd it still gives the error that sanlock
>>>is not configured.
>>>
>>> Does somebody has a solution for this?
>>>
>>> I am a bit lost on thisŠ Google only tells me that there was a bug in
>>>3.4.
>>>
>>> Thanks in advance,
>>>
>>> Jurriën
>>> This message (including any attachments) may contain information that
>>>is privileged or confidential. If you are not the intended recipient,
>>>please notify the sender and delete this email immediately from your
>>>systems and destroy all copies of it. You may not, directly or
>>>indirectly, use, disclose, distribute, print or copy this email or any
>>>part of it if you are not the intended recipient
>>
>>
>>
>> _______________________________________________
>> Users mailing list
>> Users at ovirt.org
>> http://lists.ovirt.org/mailman/listinfo/users
>>
>
>
>-- 
>Yaniv Bronhaim.