[ovirt-users] First oVirt engine deploy: missing gateway on hosts
Mauro Tridici
mauro.tridici at cmcc.it
Mon Sep 4 07:32:28 UTC 2017
Hi Kasturi,
thank you very much for your support and for the useful explanation.
If possible, I would ask you if you know a way to correct the “missing gateway” problem that I described in my previous message.
Thanks a lot,
Mauro
> Il giorno 04 set 2017, alle ore 08:51, Kasturi Narra <knarra at redhat.com> ha scritto:
>
> Hi Mauro,
>
> Creating distributed dispersed volumes are not supported from ovirt UI yet but you should be able to sync them if cluster is imported into the UI. same holds true for add / remove bricks on disperse and distribute disperse volumes.
>
> you wont be able to see bricks created because ovirt excepts them to be mounted at /rhgs/<brick-name>. What you could simply do is uncheck the check box in the 'Add brick' dialog and type in the path or you could mount your bricks at above said location and that would show all the available bricks on the host.
>
> Hope this helps.
>
> Thanks
> kasturi.
>
> On Sat, Sep 2, 2017 at 7:16 PM, Mauro Tridici <mauro.tridici at cmcc.it <mailto:mauro.tridici at cmcc.it>> wrote:
> Hi all,
>
> I just started my first Ovirt Engine deploy using a dedicated (and separated) virtual machine.
> I’m trying to create and manage a test Gluster cluster using 3 “virtual” hosts (hostnames are glu01, glu02, glu03)
> 2 different networks have been defined on the hosts (192.168.213.0/24 <http://192.168.213.0/24> for management network and 192.168.152.0/24 <http://192.168.152.0/24> for gluster network).
> Ovirt engine deploy completed without any problem, the hosts have been added easily using ovirtmgmt network (bridgeless mgmt network) and ovirtgluster (bridgeless gluster network).
>
> Everything seems to be ok for this first deploy, but I just noticed that the gateway is missing on the target hosts:
>
> [root at glu01 ~]# route
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> link-local 0.0.0.0 255.255.0.0 U 1002 0 0 ens33
> link-local 0.0.0.0 255.255.0.0 U 1003 0 0 ens34
> 192.168.152.0 0.0.0.0 255.255.255.0 U 0 0 0 ens34
> 192.168.213.0 0.0.0.0 255.255.255.0 U 0 0 0 ens33
>
> [root at glu02 ~]# route
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> link-local 0.0.0.0 255.255.0.0 U 1002 0 0 ens33
> link-local 0.0.0.0 255.255.0.0 U 1003 0 0 ens34
> 192.168.152.0 0.0.0.0 255.255.255.0 U 0 0 0 ens34
> 192.168.213.0 0.0.0.0 255.255.255.0 U 0 0 0 ens33
>
> [root at glu03 ~]# route
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> link-local 0.0.0.0 255.255.0.0 U 1002 0 0 ens33
> link-local 0.0.0.0 255.255.0.0 U 1003 0 0 ens34
> 192.168.152.0 0.0.0.0 255.255.255.0 U 0 0 0 ens34
> 192.168.213.0 0.0.0.0 255.255.255.0 U 0 0 0 ens33
>
> Due to this problem I cannot reach internet from ens33 nic (management network).
> I just tried to add the gateway in ifcfg-ens33 configuration file but gateway disappear after host reboot.
>
> [root at glu01 ~]# cat /etc/sysconfig/network-scripts/ifcfg-ens33
> # Generated by VDSM version 4.19.28-1.el7.centos
> DEVICE=ens33
> ONBOOT=yes
> IPADDR=192.168.213.151
> NETMASK=255.255.255.0
> BOOTPROTO=none
> MTU=1500
> DEFROUTE=no
> NM_CONTROLLED=no
> IPV6INIT=yes
> IPV6_AUTOCONF=yes
>
> The oVirt Engine network configuration is the following one:
>
> [host glu01]
> ens33 -> ovirtmgmt (192.168.213.151, 255.255.255.0, 192.168.213.2)
> ens34 -> ovirtgluster (192.168.152.151, 255.255.255.0)
>
> [host glu02]
> ens33 -> ovirtmgmt (192.168.213.152, 255.255.255.0, 192.168.213.2)
> ens34 -> ovirtgluster (192.168.152.152, 255.255.255.0)
>
> [host glu03]
> ens33 -> ovirtmgmt (192.168.213.153, 255.255.255.0, 192.168.213.2)
> ens34 -> ovirtgluster (192.168.152.153, 255.255.255.0)
>
> Do you know the right way to set the gateway IP on all hosts?
>
> Just two last questions: I was able to import an existing gluster cluster using oVirt Engine, but I’m not able to create a new volume because:
>
> - I can’t select a distributed disperse volume configuration from oVirt Engine volume creation window
> - i can’t see the bricks to be used to create a new volume (but I can import an existing volume without problem).
>
> Is there something that I can do to resolve the issues and complete my first experience with oVirt?
>
> Thank you very much,
> Mauro T.
>
>
> _______________________________________________
> Users mailing list
> Users at ovirt.org <mailto:Users at ovirt.org>
> http://lists.ovirt.org/mailman/listinfo/users <http://lists.ovirt.org/mailman/listinfo/users>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20170904/c6efdb0b/attachment.html>
More information about the Users
mailing list