[ovirt-users] Can't sync networks

[Cole Johnson]

I totally missed that.  Thanks, that clears it up!


On Mon, Apr 9, 2018 at 12:29 PM, Dominik Holler <dholler at redhat.com> wrote:
> Different logical networks in oVirt attached to the same host should use
> different IP networks.
>
> On Mon, 9 Apr 2018 09:16:49 -0700
> Cole Johnson <sizzlinsaguaro at gmail.com> wrote:
>
>> If I mouse over the ovirtmgmt label in "Setup Host", it indicates that
>> it is the default route.  Please see the attached screen shot.  The
>> output of ip route in the terminal shows:
>>
>> [root at kerensk ~]# ip route
>> default via 10.0.0.1 dev eno2 proto static metric 100
>> default via 10.0.0.1 dev eno3 proto static metric 101
>> 10.0.0.0/24 dev ovirtmgmt proto kernel scope link src 10.0.0.240
>> 10.0.0.0/24 dev gluster proto kernel scope link src 10.0.0.243
>> 10.0.0.0/24 dev eno2 proto kernel scope link src 10.0.0.241 metric 100
>> 10.0.0.0/24 dev eno3 proto kernel scope link src 10.0.0.242 metric 101
>> 169.254.0.0/16 dev ovirtmgmt scope link metric 1021
>> 169.254.0.0/16 dev gluster scope link metric 1028
>>
>> On Mon, Apr 9, 2018 at 8:20 AM, Dominik Holler <dholler at redhat.com>
>> wrote:
>> > On Mon, 9 Apr 2018 07:39:13 -0700
>> > Cole Johnson <sizzlinsaguaro at gmail.com> wrote:
>> >
>> >> Where can I find this information?  The best I can find is if I am
>> >> in the "Setup Host" dialog, and mouse over the un-synced network.
>> >> The message reads "Host Network's configurations differ from DC".
>> >
>> > The table below this message in dialog.jpeg shows the values not in
>> > sync, which is the default route of the host.
>> >
>> >> If this
>> >> is the error message, what do I need to do to make the
>> >> configurations match?
>> >
>> > Ensure that the gateway of ovirtmgt is the default route on the
>> > host.
>> >> Isn't this the whole point of what I am trying to do here?  I
>> >> have attached some screenshots of the different messages that I
>> >> encounter.
>> >>
>> >> On Mon, Apr 9, 2018 at 12:54 AM, Dominik Holler
>> >> <dholler at redhat.com> wrote:
>> >> > On Wed, 4 Apr 2018 11:19:33 -0700
>> >> > Cole Johnson <sizzlinsaguaro at gmail.com> wrote:
>> >> >
>> >> >> Hello,
>> >> >> I am trying to set up a 3 host gluster hyperconverged self
>> >> >> hosted engine running on oVirt Nodes. ( I think that I have all
>> >> >> of the buzzwords here) All of the hardware is the same.  I am
>> >> >> using the guide from here:
>> >> >> https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster-storage/
>> >> >> and the documentation here:
>> >> >> https://www.ovirt.org/documentation/gluster-hyperconverged/Gluster_Hyperconverged_Guide/
>> >> >> for reference.
>> >> >> I have used the setup wizards from the cockpit interface to
>> >> >> setup gluster and the hosted engine successfully.  I have
>> >> >> configured the gluster storage and setup all of the hosts
>> >> >> inside the hosted engine.
>> >> >>
>> >> >> My problem occurs when I try to configure a separate storage
>> >> >> network as shown in the blog post.  I can get thru the process
>> >> >> as outlined, on all three hosts, but the status will not change
>> >> >> from "out-of-sync".  I can press the "Sync All Networks", and I
>> >> >> get a notification which says "Finished SyncAllHostNetworks",
>> >> >> but the status of the storage network remains "out-of-sync" .
>> >> >>
>> >> >
>> >> >
>> >> > The "Setup Host Networks" dialog presents the information why the
>> >> > network is marked as "out-of-sync".
>> >> > Does the information presented helps you?
>> >> >
>> >> >> I don't know if this is related, but I cannot migrate the
>> >> >> HostedEngine vm between hosts.
>> >> >>
>> >> >> I have attached the contents of vdsm.log
>> >> >>
>> >> >> Any help is appreciated.
>> >> >
>> >
>