<div dir="ltr">The people who encountered a similar issue have just suggeted to take down both network interface and then start one of them (since they start one another). restarting the vdsm is smooth<br>and this is what I did - yet at the engine when creating a host an error while creating the host appears<br>
perhaps the engine log will help<br>googling suggests that there is mismatch of software packages and is referring to mysql so I'm not sure it's related.<br><br><br><br><div class="gmail_quote">On Mon, Jun 18, 2012 at 1:26 PM, Ofer Schreiber <span dir="ltr"><<a href="mailto:oschreib@redhat.com" target="_blank">oschreib@redhat.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div class="im"><br>
<br>
----- Original Message -----<br>
><br>
> hey<br>
> thanks for the answer.<br>
><br>
> 1. where exactly do i see the state of the host<br>
> 2. I did as you instructed. the setup fails exactly at the same step<br>
> (I changed the timeout to 600, shut down networkmanager and<br>
> connected via dhcp over ethernet.<br>
<br>
</div>Weird, which line did you changed? does the log still saying the host status is "installing"?<br>
<div class="im"><br>
> 2. I manually configured as following<br>
><br>
> /etc/sysconfig/network-scripts/ifcfg-ovirtmgmt<br>
> DEVICE=ovirtmgmt<br>
> TYPE=Bridge<br>
> ONBOOT=yes<br>
> DELAY=0<br>
> BOOTPROTO=dhcp<br>
> NM_CONTROLLED="no<br>
><br>
> and added<br>
> BRIDGE=ovirtmgmt<br>
> to the ifcfg-eth0<br>
><br>
><br>
> restarting the network service fails with a status error<br>
> RTNETLINK answers: File exists.<br>
<br>
</div>Again, sounds like something is bad with your network configuration.<br>
There are multiple results in google for that issue...<br>
<div class="HOEnZb"><div class="h5"><br>
><br>
> thanks<br>
><br>
><br>
><br>
> On Mon, Jun 18, <a href="tel:2012" value="+9722012">2012</a> at 11:21 AM, Ofer Schreiber <<br>
> <a href="mailto:oschreib@redhat.com">oschreib@redhat.com</a> > wrote:<br>
><br>
><br>
><br>
> ><br>
> > the bootstrap logs are also available<br>
> > here they are.<br>
> > thanks.<br>
><br>
> 1. If you log into the GUI, in which state is the host?<br>
><br>
> 2. From the engine.log, I can see that the host installation went<br>
> fine, and it seems that the host is in "Non-Operetional state).<br>
> - I can see clearly in the log :"Host local_host is set to<br>
> Non-Operational, it is missing the following networks: ovirtmgmt"<br>
><br>
> 3. in the vds_bootstrap.498578.log you can see "ERROR<br>
> _getBridgeParams: failed to read params of file<br>
> /etc/sysconfig/network-scripts/ifcfg-wlan0." - it seems that<br>
> something is wrong with your networking configuration<br>
><br>
> 4. Probably the timeout during all-in-one installation (150 seconds)<br>
> is too low for you.<br>
><br>
><br>
> Two options for you:<br>
> 1. Clean everything (using engine-cleanup), fix you networking<br>
> settings (disable NetworkManager, use non wireless conntection) and<br>
> rerun engine-setup (with higher timeout in<br>
> /usr/share/ovirt-engine/scripts/plugins/all_in_one_100.py)<br>
><br>
> 2. Just create the ovirtmgmt network bridge by your self, and restart<br>
> vdsm.<br>
><br>
><br>
><br>
> ><br>
> ><br>
> ><br>
> > On Mon, Jun 18, <a href="tel:2012" value="+9722012">2012</a> at 10:40 AM, Ofer Schreiber <<br>
> > <a href="mailto:oschreib@redhat.com">oschreib@redhat.com</a> > wrote:<br>
> ><br>
> ><br>
> ><br>
> ><br>
> ><br>
> > ----- Original Message -----<br>
> > ><br>
> > > The log is attached.<br>
> > ><br>
> > > thanks<br>
> ><br>
> > I'm missing the vds_bootstrap* logs. are they available?<br>
> > if not, if you log into the GUI, in which state the host is<br>
> > currently<br>
> > at?<br>
> ><br>
> > (/var/log/ovirt-enging/*log might help as well)<br>
> ><br>
> ><br>
> ><br>
> > ><br>
> > ><br>
> > ><br>
> > > On Mon, Jun 18, <a href="tel:2012" value="+9722012">2012</a> at 10:26 AM, Ofer Schreiber <<br>
> > > <a href="mailto:oschreib@redhat.com">oschreib@redhat.com</a> > wrote:<br>
> > ><br>
> > ><br>
> > > It seems that the host is currently in "installing" state.<br>
> > > Could you please take a look (or attach us) the vdsm installation<br>
> > > logs under /tmp?<br>
> > > (/tmp/vds_*)<br>
> > ><br>
> > ><br>
> > ><br>
> > > ----- Original Message -----<br>
> > > ><br>
> > > > Hello.<br>
> > > ><br>
> > > > I'm experiencing a problem during installation of the ovirt<br>
> > > > engine<br>
> > > > including the all-in-one plugin<br>
> > > > The setup exists during the stage "Adding local host" - it<br>
> > > > quits<br>
> > > > due<br>
> > > > to a "time out while waiting for the host to start"<br>
> > > > I've attached some info (including the setup's log) and will<br>
> > > > gladly<br>
> > > > provide more information if necessary.<br>
> > > ><br>
> > > > Many thanks,<br>
> > > ><br>
> > > > Ohad<br>
> > > ><br>
> > > ><br>
> > ><br>
> > ><br>
> ><br>
> ><br>
><br>
><br>
</div></div></blockquote></div><br></div>