<div dir="ltr">Hello,<div>on a 2 nodes cluster in 4.1.6 I have this situation.</div><div>Every node has 3 bonds, each one composed by 2 network adapters and each one of type mode=4<br><div>(actually in setup networks I have configured custom and then the value: </div><div>&quot;mode=4 miimon=100&quot;</div><div>)</div><div><br></div><div>At this moment only one of the servers has access to FC storage, while the other is currently on maintenance.</div><div><br></div><div>On 2 of the 3 bonds of the active server I get an exclamation point in &quot;Network Interfaces&quot; subtab with this mouseover popup</div><div><br></div><div>Bond is in link aggregation mode (mode 4), but no partner mac has been reported for it<br></div></div><div><br></div><div>What is the exact meaning of this message? Do I have to care about (I think so..)?</div><div>What should I report to network guys?</div><div>Eg, one of these two warning bonds status is:</div><div><br></div><div><div># cat /proc/net/bonding/bond2</div><div>Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)</div><div><br></div><div>Bonding Mode: IEEE 802.3ad Dynamic link aggregation</div><div>Transmit Hash Policy: layer2 (0)</div><div>MII Status: up</div><div>MII Polling Interval (ms): 100</div><div>Up Delay (ms): 0</div><div>Down Delay (ms): 0</div><div><br></div><div>802.3ad info</div><div>LACP rate: slow</div><div>Min links: 0</div><div>Aggregator selection policy (ad_select): stable</div><div>System priority: 65535</div><div>System MAC address: 48:df:37:0c:7f:5a</div><div>Active Aggregator Info:</div><div>        Aggregator ID: 5</div><div>        Number of ports: 2</div><div>        Actor Key: 9</div><div>        Partner Key: 6</div><div>        Partner Mac Address: b8:38:61:9c:75:80</div><div><br></div><div>Slave Interface: ens2f2</div><div>MII Status: up</div><div>Speed: 1000 Mbps</div><div>Duplex: full</div><div>Link Failure Count: 2</div><div>Permanent HW addr: 48:df:37:0c:7f:5a</div><div>Slave queue ID: 0</div><div>Aggregator ID: 5</div><div>Actor Churn State: none</div><div>Partner Churn State: none</div><div>Actor Churned Count: 2</div><div>Partner Churned Count: 3</div><div>details actor lacp pdu:</div><div>    system priority: 65535</div><div>    system mac address: 48:df:37:0c:7f:5a</div><div>    port key: 9</div><div>    port priority: 255</div><div>    port number: 1</div><div>    port state: 61</div><div>details partner lacp pdu:</div><div>    system priority: 32768</div><div>    system mac address: b8:38:61:9c:75:80</div><div>    oper key: 6</div><div>    port priority: 32768</div><div>    port number: 293</div><div>    port state: 61</div><div><br></div><div>Slave Interface: ens2f3</div><div>MII Status: up</div><div>Speed: 1000 Mbps</div><div>Duplex: full</div><div>Link Failure Count: 2</div><div>Permanent HW addr: 48:df:37:0c:7f:5b</div><div>Slave queue ID: 0</div><div>Aggregator ID: 5</div><div>Actor Churn State: none</div><div>Partner Churn State: none</div><div>Actor Churned Count: 0</div><div>Partner Churned Count: 3</div><div>details actor lacp pdu:</div><div>    system priority: 65535</div><div>    system mac address: 48:df:37:0c:7f:5a</div><div>    port key: 9</div><div>    port priority: 255</div><div>    port number: 2</div><div>    port state: 61</div><div>details partner lacp pdu:</div><div>    system priority: 32768</div><div>    system mac address: b8:38:61:9c:75:80</div><div>    oper key: 6</div><div>    port priority: 32768</div><div>    port number: 549</div><div>    port state: 61</div></div><div><br></div><div>Also, the other node (that is currently in maintenance) shows one of the 2 interfaces of bond2 (ens2f2) as down (red arrow) but on the host</div><div><br></div><div># ip link show ens2f2</div><div>6: ens2f2: &lt;BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP&gt; mtu 1500 qdisc mq master bond2 state UP mode DEFAULT qlen 1000</div><div>    link/ether 48:df:37:0c:85:4e brd ff:ff:ff:ff:ff:ff</div><div># </div><div><br></div><div>Does this depend on the host being in maintenance? </div><div>Perhaps when a host is in maintenance, the warnings on it are not checked/updated again from engine?</div><div><br></div><div>Thanks in advance,</div><div>Gianluca</div><div><br></div><div> </div></div>