Re: [Users] ovirt-node install hangs

Hi, yesterday I tried the new oVirt Node 2.5.3. I tried installing it without the quiet flag but no luck. It hanged again and the kernel didn't show any error on console (tty2). Later will test without the rhgh flag.

Alex BTW, now the hostname works on 2.5.3 :-) The network configuration is still tricky... sometimes I have an "Apply" sometimes only a "Back" choice.

2012/10/9 Alexandre Santos <santosam72(a)gmail.com&gt; It's working now :-) Thanks a lot all! Alex P.S. I haven't tried installing it on my SATA disk because I have there a Local Node already running but I'm going to try again on another one to see if I can send to you the error log. 2012/10/8 Mike Burns <mburns(a)redhat.com&gt; On Mon, 2012-10-08 at 09:54 +0100, Alexandre Santos wrote: > > > 2012/10/8 Fabian Deutsch <fabiand(a)redhat.com&gt; > Am Montag, den 08.10.2012, 09:24 +0100 schrieb Alexandre > Santos: > > 2012/10/8 Fabian Deutsch <fabiand(a)redhat.com&gt; > > Hey, > > > > Am Sonntag, den 07.10.2012, 15:29 +0100 schrieb > Alexandre > > Santos: > > > Hi, > > > I'm trying to install the ovirt-node iso image on > a SATA > > disk and when > > > it gets to the screen where it shows 25% completed > the > > kernel hangs. I > > > can't connect using a serial console to see what > has > > happened. If I > > > reboot using a usb linux disk I see that the SATA > disk has > > been > > > formated and the partitions that existed before > disappeared, > > being > > > there just one partition of type "ee" > > > > > > Is there any error displayed when kernel hangs at > 25%? And it > > can take > > some time to pass the 25% (up to ~2min or so). > > > > No, I think it's a kernel hang because the lights on the > keyboard halt > > and I can't change to tty2, etc.. I even changed to tty2 and > waited to > > see if there were some errors but nothing. I've read that > "tty8" was > > the logging console but no luck also. > > BTW, I tried with an IDE disk and the result was the same. > > > Mh, okay. > Could you try booting without the rhgb and quiet kernel > arguments. I > hope that some errors will be displayed on the screen so we > get an idea > about the problem. > > > > > > If I use a 8 GB usb pen-drive instead of the SATA > disk, the > > > installation comes to an end and I reboot but then > I get > > some error > > > about not getting /dev/mapper/by-name/Root and the > boot > > fails to a > > > dracut shell. > > > Any ideas? > > > > > > In the dracut shell, could you run blkid and post > the results? > > > > I noticed that the USB Disk was named RootBackup instead of > Root... I > > then rebooted and chose uninstall and then installed oVirt > Node from > > scratch and now it worked. Glad it worked the second time. There should be 4 partitions on the disk. Partition 1 is for UEFI or bios_boot depending on your machine type. Partition 2 and Partition 3 are Root and RootBackup. So seeing a RootBackup is correct. Not seeing a Root is incorrect. If you rebooted the host in the middle of the install, or if the install hung for some reason, I can see that situation happening and see it working after uninstall/install. > > I can't activate Networking because I have that "no > hostname" error > > mentioned in another post. I think it's related to that... You can't activate networking at all? That is news to me. The node should work perfectly fine with or without a FQDN. > > > Yes, I've also seen the hostname error. And I've also seen > some problems > with the rootfs lately. Have you seen these issues with the 2.5.2 build? Or only master branch builds? > Could you provide a screenshot/dump of the console with that > error? > > - fabian > > > Ok! I'll send them as soon as possible. > > Alex > > > _______________________________________________ > Users mailing list > Users(a)ovirt.org > http://lists.ovirt.org/mailman/listinfo/users _______________________________________________ Users mailing list Users(a)ovirt.org http://lists.ovirt.org/mailman/listinfo/users