I built a new Engine Server on 3.3.2-1.el6, rebuilt my VM's and I no longer see the
issue. All is now working as expected.
Simon
-----Original Message-----
From: Simon Barrett
Sent: 08 January 2014 08:50
To: Lior Vernia; Itamar Heim
Cc: users(a)ovirt.org
Subject: RE: [Users] Network profile lost after host edit
To test this further I setup another 3.3.2-1.el6 ovirt-engine. I'm not seeing the same
problem on the new engine.
I'm going to try and move all configuration/VM's etc from the problem ovirt-engine
install to the new one to see if the problem re-appears.
I'll let you know how it goes.
Simon
-----Original Message-----
From: Lior Vernia [mailto:lvernia@redhat.com]
Sent: 08 January 2014 06:02
To: Itamar Heim
Cc: Simon Barrett; users(a)ovirt.org
Subject: Re: [Users] Network profile lost after host edit
On 07/01/14 23:16, Itamar Heim wrote:
On 01/07/2014 08:59 AM, Lior Vernia wrote:
> Hi Simon,
>
> Thank you so much for tracking this down. I'm currently immersed in
> oVirt 3.4 feature stuff, but I just wanted to let you know I saw this
> and am planning to take care of it; I'll take a look in a week or two
> when things calm down.
>
> The bad news are, I suspect there will be no workaround other than
> upgrading to the next version that will include the fix (likely 3.3.3).
>
is there an ovirt bug targeted to 3.3.3 tracking this?
I'll open one as soon as I test the issue. Unless Simon would like to pick up the
gauntlet and open one on bugzilla.redhat.com?...
> Yours, Lior.
>
> On 06/01/14 12:21, Simon Barrett wrote:
>> I am now able to reproduce the problem where network profile
>> definitions are lost on VM edit.
>>
>> - Create VM
>> - From the "Network Interfaces" tab, click on "New" and
assign the
>> ovirtmgt profile to nic1
>> - Edit VM, from the "nic1" drop down select another profile and
>> click OK
>> - Edit the same VM again and nic1 lists as <Empty>
>>
>> I upgraded to 3.3.2-1.el6 and still see the problem.
>>
>> As ever, any help is very much appreciated.
>>
>> Thanks,
>>
>> Simon
>>
>>
>> -----Original Message-----
>> From: users-bounces(a)ovirt.org [mailto:users-bounces@ovirt.org] On
>> Behalf Of Simon Barrett
>> Sent: 12 December 2013 21:53
>> To: Lior Vernia
>> Cc: users(a)ovirt.org
>> Subject: Re: [Users] Network profile lost after host edit
>>
>> Lior,
>>
>> I'm running 3.3.1.
>>
>> I think it may be related to how I created the VM's. Another VM
>> created using the blank template works fine and the network config
>> displays correctly when I click on edit.
>>
>> The problem VM's were created with a different template. I'll dig a
>> bit further to see if I can narrow it down any further.
>>
>> I don't have to click show advanced to exhibit the problem.
>>
>> Thanks for the response
>>
>> Simon
>>
>>> On 12 Dec 2013, at 16:44, "Lior Vernia" <lvernia(a)redhat.com>
wrote:
>>>
>>> Hi Simon,
>>>
>>> I apologize for the delay in my response. I've worked quite a bit
>>> on that part of the dialog since oVirt 3.3, and while it was quite
>>> buggy I haven't encountered this exact issue you're describing. It
>>> does remind me of one bug though; could it be that pressing the
>>> "Show Advanced Options" is what triggers the strange behavior?
>>>
>>> What version of oVirt engine are you running? Both 3.3.1 and 3.3.2
>>> should be quite stable as far as this dialog is concerned, so
>>> upgrading might be a good idea.
>>>
>>> As for workarounds, it sounds like a GUI issue so I don't think
>>> there's anything you can do apart from upgrading the engine.
>>>
>>> Yours, Lior.
>>>
>>>> On 11/12/13 13:40, Simon Barrett wrote:
>>>> I have a problem where VM network profiles are lost when editing a
>>>> host.
>>>> E.G.
>>>>
>>>>
>>>>
>>>> * VM is running fine on the correct network. Network
>>>> Interfaces
>>>> tab shows "nic1" and "Network Name" shows the correct
network profile.
>>>>
>>>> * I shutdown the VM then right click and Edit.
>>>>
>>>> * The General settings for the node shows "nic1
<Empty>". If I
>>>> then edit config, something like increasing memory or changing CPU
>>>> cores then click on OK, the VM configuration is saved without a
>>>> network profile.
>>>>
>>>> * When I boot the VM I cannot connect to it.
>>>>
>>>> * I then have to edit the node again configure back in the
>>>> correct network profile.
>>>>
>>>>
>>>>
>>>> Does anyone know if this is a known issue? If not, any suggestions
>>>> as to how I correct this so that the original network profile
>>>> definition is retained after an edit?
>>>>
>>>>
>>>>
>>>> Many thanks,
>>>>
>>>>
>>>>
>>>> Simon
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> Users mailing list
>>>> Users(a)ovirt.org
>>>>
http://lists.ovirt.org/mailman/listinfo/users
>>>>
>> _______________________________________________
>> Users mailing list
>> Users(a)ovirt.org
>>
http://lists.ovirt.org/mailman/listinfo/users
>>
> _______________________________________________
> Users mailing list
> Users(a)ovirt.org
>
http://lists.ovirt.org/mailman/listinfo/users
>