9:51 a.m.
Hi Mauro,
Creating distributed dispersed volumes are not supported from ovirt
UI yet but you should be able to sync them if cluster is imported into the
UI. same holds true for add / remove bricks on disperse and distribute
disperse volumes.
you wont be able to see bricks created because ovirt excepts them to
be mounted at /rhgs/<brick-name>. What you could simply do is uncheck the
check box in the 'Add brick' dialog and type in the path or you could mount
your bricks at above said location and that would show all the available
bricks on the host.
Hope this helps.
Thanks
kasturi.
On Sat, Sep 2, 2017 at 7:16 PM, Mauro Tridici <mauro.tridici(a)cmcc.it> wrote:
Hi all,
I just started my first Ovirt Engine deploy using a dedicated (and
separated) virtual machine.
I’m trying to create and manage a test Gluster cluster using 3 “virtual”
hosts (hostnames are glu01, glu02, glu03)
2 different networks have been defined on the hosts (192.168.213.0/24 for
management network and 192.168.152.0/24 for gluster network).
Ovirt engine deploy completed without any problem, the hosts have been
added easily using ovirtmgmt network (bridgeless mgmt network) and
ovirtgluster (bridgeless gluster network).
Everything seems to be ok for this first deploy, but I just noticed that
the gateway is missing on the target hosts:
[root@glu01 ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
link-local 0.0.0.0 255.255.0.0 U 1002 0 0
ens33
link-local 0.0.0.0 255.255.0.0 U 1003 0 0
ens34
192.168.152.0 0.0.0.0 255.255.255.0 U 0 0 0
ens34
192.168.213.0 0.0.0.0 255.255.255.0 U 0 0 0
ens33
[root@glu02 ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
link-local 0.0.0.0 255.255.0.0 U 1002 0 0
ens33
link-local 0.0.0.0 255.255.0.0 U 1003 0 0
ens34
192.168.152.0 0.0.0.0 255.255.255.0 U 0 0 0
ens34
192.168.213.0 0.0.0.0 255.255.255.0 U 0 0 0
ens33
[root@glu03 ~]# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
link-local 0.0.0.0 255.255.0.0 U 1002 0 0
ens33
link-local 0.0.0.0 255.255.0.0 U 1003 0 0
ens34
192.168.152.0 0.0.0.0 255.255.255.0 U 0 0 0
ens34
192.168.213.0 0.0.0.0 255.255.255.0 U 0 0 0
ens33
Due to this problem I cannot reach internet from ens33 nic (management
network).
I just tried to add the gateway in ifcfg-ens33 configuration file but
gateway disappear after host reboot.
[root@glu01 ~]# cat /etc/sysconfig/network-scripts/ifcfg-ens33
# Generated by VDSM version 4.19.28-1.el7.centos
DEVICE=ens33
ONBOOT=yes
IPADDR=192.168.213.151
NETMASK=255.255.255.0
BOOTPROTO=none
MTU=1500
DEFROUTE=no
NM_CONTROLLED=no
IPV6INIT=yes
IPV6_AUTOCONF=yes
The oVirt Engine network configuration is the following one:
[host glu01]
ens33 -> ovirtmgmt (192.168.213.151, 255.255.255.0, 192.168.213.2)
ens34 -> ovirtgluster (192.168.152.151, 255.255.255.0)
[host glu02]
ens33 -> ovirtmgmt (192.168.213.152, 255.255.255.0, 192.168.213.2)
ens34 -> ovirtgluster (192.168.152.152, 255.255.255.0)
[host glu03]
ens33 -> ovirtmgmt (192.168.213.153, 255.255.255.0, 192.168.213.2)
ens34 -> ovirtgluster (192.168.152.153, 255.255.255.0)
Do you know the right way to set the gateway IP on all hosts?
Just two last questions: I was able to import an existing gluster cluster
using oVirt Engine, but I’m not able to create a new volume because:
- I can’t select a distributed disperse volume configuration from oVirt
Engine volume creation window
- i can’t see the bricks to be used to create a new volume (but I can
import an existing volume without problem).
Is there something that I can do to resolve the issues and complete my
first experience with oVirt?
Thank you very much,
Mauro T.
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users