moin, i have learned to install a self hosted engine directly to the physical interfaces. later you can move it with the hosted engine into the different bonds or vlans. it works fine by me round 20 times. br marcel Am 3. Februar 2021 19:56:47 MEZ schrieb Nardus Geldenhuys <nardusg@gmail.com>:
Hi oVirt land
Hope you are well. Running into this issue, I hope you can help.
Centos7 and it is updated. Ovirt 4.3, latest packages.
My network config:
[root@mob-r1-d-ovirt-aa-1-01 ~]# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens1f0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff 3: ens1f1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP group default qlen 1000 link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff 4: enp11s0f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000 link/ether 00:90:fa:c2:d2:50 brd ff:ff:ff:ff:ff:ff 5: enp11s0f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000 link/ether 00:90:fa:c2:d2:54 brd ff:ff:ff:ff:ff:ff 21: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff inet6 fe80::290:faff:fec2:d248/64 scope link valid_lft forever preferred_lft forever 22: bond0.1131@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 00:90:fa:c2:d2:48 brd ff:ff:ff:ff:ff:ff inet 172.18.206.184/23 brd 172.18.207.255 scope global bond0.1131 valid_lft forever preferred_lft forever inet6 fe80::290:faff:fec2:d248/64 scope link valid_lft forever preferred_lft forever
[root@mob-r1-d-ovirt-aa-1-01 network-scripts]# cat ifcfg-bond0 BONDING_OPTS='mode=1 miimon=100' TYPE=Bond BONDING_MASTER=yes PROXY_METHOD=none BROWSER_ONLY=no IPV6INIT=no NAME=bond0 UUID=c11ef6ef-794f-4683-a068-d6338e5c19b6 DEVICE=bond0 ONBOOT=yes [root@mob-r1-d-ovirt-aa-1-01 network-scripts]# cat ifcfg-bond0.1131 DEVICE=bond0.1131 VLAN=yes ONBOOT=yes MTU=1500 IPADDR=172.18.206.184 NETMASK=255.255.254.0 GATEWAY=172.18.206.1 BOOTPROTO=none MTU=1500 DEFROUTE=yes NM_CONTROLLED=no IPV6INIT=yes DNS1=172.20.150.10 DNS2=172.20.150.11
I get the following error:
[ INFO ] TASK [ovirt.hosted_engine_setup : Generate output list] [ INFO ] ok: [localhost] [ INFO ] TASK [ovirt.hosted_engine_setup : Validate selected bridge interface if management bridge does not exists] [ INFO ] skipping: [localhost] Please indicate a nic to set ovirtmgmt bridge on: (bond0, bond0.1131) [bond0.1131]: Please specify which way the network connectivity should be checked (ping, dns, tcp, none) [dns]: .. .. .. .. .. [ INFO ] ok: [localhost] [ INFO ] TASK [ovirt.hosted_engine_setup : Validate selected bridge interface if management bridge does not exists] [ ERROR ] fatal: [localhost]: FAILED! => {"changed": false, "msg": "The selected network interface is not valid"} [ ERROR ] Failed to execute stage 'Closing up': Failed executing ansible-playbook [ INFO ] Stage: Clean up
And if I create the ifcfg-ovirtmgmt as a bridge it fails later.
What is the correct network setup for my bond configuration to do a self hosted-engine setup ?
Regards
Nar