Re: [Users] Network profile lost after host edit

Hi Simon, Thank you so much for tracking this down. I'm currently immersed in oVirt 3.4 feature stuff, but I just wanted to let you know I saw this and am planning to take care of it; I'll take a look in a week or two when things calm down. The bad news are, I suspect there will be no workaround other than upgrading to the next version that will include the fix (likely 3.3.3).

Yours, Lior. On 06/01/14 12:21, Simon Barrett wrote: > I am now able to reproduce the problem where network profile definitions are lost on VM edit. > > - Create VM > - From the "Network Interfaces" tab, click on "New" and assign the ovirtmgt profile to nic1 > - Edit VM, from the "nic1" drop down select another profile and click OK > - Edit the same VM again and nic1 lists as <Empty> > > I upgraded to 3.3.2-1.el6 and still see the problem. > > As ever, any help is very much appreciated. > > Thanks, > > Simon > > > -----Original Message----- > From: users-bounces(a)ovirt.org [mailto:users-bounces@ovirt.org] On Behalf Of Simon Barrett > Sent: 12 December 2013 21:53 > To: Lior Vernia > Cc: users(a)ovirt.org > Subject: Re: [Users] Network profile lost after host edit > > Lior, > > I'm running 3.3.1. > > I think it may be related to how I created the VM's. Another VM created using the blank template works fine and the network config displays correctly when I click on edit. > > The problem VM's were created with a different template. I'll dig a bit further to see if I can narrow it down any further. > > I don't have to click show advanced to exhibit the problem. > > Thanks for the response > > Simon > >> On 12 Dec 2013, at 16:44, "Lior Vernia" <lvernia(a)redhat.com&gt; wrote: >> >> Hi Simon, >> >> I apologize for the delay in my response. I've worked quite a bit on >> that part of the dialog since oVirt 3.3, and while it was quite buggy >> I haven't encountered this exact issue you're describing. It does >> remind me of one bug though; could it be that pressing the "Show >> Advanced Options" is what triggers the strange behavior? >> >> What version of oVirt engine are you running? Both 3.3.1 and 3.3.2 >> should be quite stable as far as this dialog is concerned, so >> upgrading might be a good idea. >> >> As for workarounds, it sounds like a GUI issue so I don't think >> there's anything you can do apart from upgrading the engine. >> >> Yours, Lior. >> >>> On 11/12/13 13:40, Simon Barrett wrote: >>> I have a problem where VM network profiles are lost when editing a host. >>> E.G. >>> >>> >>> >>> * VM is running fine on the correct network. Network Interfaces >>> tab shows "nic1" and "Network Name" shows the correct network profile. >>> >>> * I shutdown the VM then right click and Edit. >>> >>> * The General settings for the node shows "nic1 <Empty>". If I >>> then edit config, something like increasing memory or changing CPU >>> cores then click on OK, the VM configuration is saved without a network profile. >>> >>> * When I boot the VM I cannot connect to it. >>> >>> * I then have to edit the node again configure back in the >>> correct network profile. >>> >>> >>> >>> Does anyone know if this is a known issue? If not, any suggestions as >>> to how I correct this so that the original network profile definition >>> is retained after an edit? >>> >>> >>> >>> Many thanks, >>> >>> >>> >>> Simon >>> >>> >>> >>> >>> >>> _______________________________________________ >>> Users mailing list >>> Users(a)ovirt.org >>> http://lists.ovirt.org/mailman/listinfo/users >>> > _______________________________________________ > Users mailing list > Users(a)ovirt.org > http://lists.ovirt.org/mailman/listinfo/users > _______________________________________________ Users mailing list Users(a)ovirt.org http://lists.ovirt.org/mailman/listinfo/users