10:57 p.m.
Trying to get my ovirt cluster connected to my vSphere cluster to import my guests. When
trying to connect, I get:
"VDSM ovirt1 command GetVmsNamesFromExternalProviderVDS failed: internal error:
curl_easy_perform() returned an error: Couldn't connect to server (7) : Failed connect
to 10.0.0.55:443; Connection timed out"
ovirt1 node (192.168.1.195) is at location A while vSphere (10.0.0.55) is at location B.
I added a static route on ovirt1 for 10.0.0.0/8 via 192.168.1.13, which has a VPN
connection back to 10.0.0.0/8. ICMP from ovirt1 gets through just fine, but any other
traffic never leaves ovirt1 (ie: 443 traffic never arrives at 1.13).
I'm assuming there's some firewall rule somewhere, blocking anything other than
outbound ICMP, but I have been unable to find it. Any suggestions?
10 a.m.
New subject: routing/firewalling problems (was: oVirt can't communicate with vSphere)
On Wed, Jan 30, 2019 at 9:59 PM Benjamin Selinger <blistovmhz(a)gmail.com> wrote:
Trying to get my ovirt cluster connected to my vSphere cluster to import my guests. When
trying to connect, I get:
"VDSM ovirt1 command GetVmsNamesFromExternalProviderVDS failed: internal error:
curl_easy_perform() returned an error: Couldn't connect to server (7) : Failed connect
to 10.0.0.55:443; Connection timed out"
ovirt1 node (192.168.1.195) is at location A while vSphere (10.0.0.55) is at location B.
I added a static route on ovirt1 for 10.0.0.0/8 via 192.168.1.13, which has a VPN
connection back to 10.0.0.0/8. ICMP from ovirt1 gets through just fine, but any other
traffic never leaves ovirt1 (ie: 443 traffic never arrives at 1.13).
I'm assuming there's some firewall rule somewhere, blocking anything other than
outbound ICMP, but I have been unable to find it. Any suggestions?
Maybe manually connect (with netcat or telnet) to port 443 on B? Does
this work? If not, debug until it works, then try again.
If you can, you can try sniffing both interfaces of the vpn gateway,
to try and see what traffic does get through and what fails, in
addition to sniffing the end points. Did you add a route to B? You
might need one as well.
(Also changing the subject)
Good luck and best regards,
--
Didi
7:57 p.m.
New subject: routing/firewalling problems (was: oVirt can't communicate with vSphere)
No. As I said, ICMP is routed through correctly without any issue. The routing is correct,
and the machine at 1.13 is definitely forwarding requests correctly. I've tested from
another machine on my LAN, same setup except not running Centos/ovirt and it's got no
problem with communication.
Telnet from 1.195 never leaves the node, and never hits 1.13. I can successfully hit the
10.0.0.0/8 network from any other machine on my network.
I reinstalled the cluster (for various reasons) yesterday, using the ovirt-node installer,
and same issue. I dunno if I'm just derping out, but I can't see where it's
being blocked.
12:56 p.m.
New subject: routing/firewalling problems (was: oVirt can't communicate with vSphere)
On Sat, Feb 2, 2019 at 7:34 PM Benjamin Selinger <blistovmhz(a)gmail.com> wrote:
No. As I said, ICMP is routed through correctly without any issue. The routing is
correct, and the machine at 1.13 is definitely forwarding requests correctly. I've
tested from another machine on my LAN, same setup except not running Centos/ovirt and
it's got no problem with communication.
Telnet from 1.195 never leaves the node,
As in, does not reach the gateway/vpn? Did you sniff traffic on the
node and the gateway to verify?
Please check/share iptables/firewalld config on the node, if you
suspect that it's blocking outgoing traffic (but I do not think
ovirt-node ever does this by default).
IMO it should not be hard to make iptables on the node log all blocks,
but I didn't try this recently (or at all, with firewalld).
and never hits 1.13. I can successfully hit the 10.0.0.0/8 network
from any other machine on my network.
I reinstalled the cluster (for various reasons) yesterday, using the ovirt-node
installer, and same issue. I dunno if I'm just derping out, but I can't see where
it's being blocked.
I'd suggest to sniff traffic in all relevant places and try to
identify the box that does not forward correctly. Then we can start
diagnosing why it does not.
Best regards,
--
Didi
2119
days inactive
2123
days old
3 comments
2 participants
participants (2)
-
Benjamin Selinger -
Yedidyah Bar David