10:32 a.m.
Hello list,
Just wanted to get your opinion on my ovirt home lab setup. While this
is not a production setup I would like it to run relatively reliably so
please tell me if the following storage configuration is likely to
result in corruption or just bat s**t insane.
I have a 3 node hosted engine setup, VM data store and engine data store
are both replica 3 gluster volumes (one brick on each host).
I do not want to run all 3 hosts 24/7 due to electricity costs, I only
power up the larger hosts (2 Dell R710's) when I need additional
resources for VM's.
I read about using CTDB and floating/virtual IP's to allow the storage
mount point to transition between available hosts but after some thought
decided to go about this another, simpler, way:
I created a common hostname for the storage mount points: gfs-data and
gfs-engine
On each host I edited /etc/hosts file to have these hostnames resolve to
each hosts IP i.e. on host1 gfs-data & gfs-engine --> host1 IP
on host2 gfs-data & gfs-engine --> host2 IP
etc.
In ovirt engine each storage domain is mounted as gfs-data:/data and
gfs-engine:/engine
My thinking is that this way no matter which host is up and acting as
SPM it will be able to mount the storage as its only dependent on that
host being up.
I changed gluster options for server-quorum-ratio so that the volumes
remain up even if quorum is not met, I know this is risky but its just a
lab setup after all.
So, any thoughts on the /etc/hosts method to ensure the storage mount
point is always available? Is data corruption more or less inevitable
with this setup? Am I insane ;) ?
Thanks,
12:08 p.m.
On 11 February 2017 at 13:32, Bartosiak-Jentys, Chris <
chris.bartosiak-jentys(a)certico.co.uk> wrote:
Hello list,
Just wanted to get your opinion on my ovirt home lab setup. While this is
not a production setup I would like it to run relatively reliably so please
tell me if the following storage configuration is likely to result in
corruption or just bat s**t insane.
I have a 3 node hosted engine setup, VM data store and engine data store
are both replica 3 gluster volumes (one brick on each host).
I do not want to run all 3 hosts 24/7 due to electricity costs, I only
power up the larger hosts (2 Dell R710's) when I need additional resources
for VM's.
I read about using CTDB and floating/virtual IP's to allow the storage
mount point to transition between available hosts but after some thought
decided to go about this another, simpler, way:
I created a common hostname for the storage mount points: gfs-data and
gfs-engine
On each host I edited /etc/hosts file to have these hostnames resolve to
each hosts IP i.e. on host1 gfs-data & gfs-engine --> host1 IP
on host2 gfs-data & gfs-engine --> host2 IP
etc.
In ovirt engine each storage domain is mounted as gfs-data:/data and
gfs-engine:/engine
My thinking is that this way no matter which host is up and acting as SPM
it will be able to mount the storage as its only dependent on that host
being up.
I changed gluster options for server-quorum-ratio so that the volumes
remain up even if quorum is not met, I know this is risky but its just a
lab setup after all.
So, any thoughts on the /etc/hosts method to ensure the storage mount
point is always available? Is data corruption more or less inevitable with
this setup? Am I insane ;) ?
Why not just use localhost? And no need for CTDB with a floating IP, oVirt
uses libgfapi for Gluster which deals with that all natively.
As for the quorum issue, I would most definitely *not* run with quorum
disabled when you're running more than one node. As you say you
specifically plan for when the other 2 nodes of the replica 3 set will be
active or not, I'd do something along the lines of the following...
Going from 3 nodes to 1 node:
- Put nodes 2 & 3 in maintenance to offload their virtual load;
- Once the 2 nodes are free of load, disable quorum on the Gluster volumes;
- Power down the 2 nodes.
Going from 1 node to 3 nodes:
- Power on *only* 1 of the pair of nodes (if you power on both & self-heal
is enabled, Gluster will "heal" the files on the main node with the older
files on the 2 nodes which were powered down);
- Allow Gluster some time to detect that the files are in split-brain;
- Tell Gluster to heal the files in split-brain based on modification time;
- Once the 2 nodes are in sync, re-enable quorum & power on the last node,
which will be resynchronised automatically;
- Take the 2 hosts out of maintenance mode.
If you want to power on the 2nd two nodes at the same time, make absolutely
sure self-heal is disabled first! If you don't, Gluster will see the 2nd
two nodes as in quorum & heal the data on your 1st node with the
out-of-date data.
--
Doug
12:39 p.m.
--=_a529982ddfb8bfce09fad28eff29c930
Content-Transfer-Encoding: 7bit
Content-Type: text/plain; charset=US-ASCII
Thank you for your reply Doug,
I didn't use localhost as I was preparing to follow instructions (blog
post:
http://community.redhat.com/blog/2014/11/up-and-running-with-ovirt-3-5-pa...)
for setting up CTDB and had already created hostnames for the floating
IP when I decided to ditch that and go with the hosts file hack. I
already had the volumes mounted on those hostnames but you are
absolutely right, simply using localhost would be the best option.
Thank you for your suggested outline of how to power up/down the
cluster, I hadn't considered the fact that turning on two out of date
nodes would clobber data on the new node. This is something I will need
to be very careful to avoid. The setup is mostly for lab work so not
really mission critical but I do run a few VM's (freeIPA, GitLab and
pfSense) that I'd like to keep up 24/7. I make regular backups (outside
of ovirt) of those just in case.
Thanks, I will do some reading on how gluster handles quorum and heal
operations but your procedure sounds like a sensible way to operate this
cluster.
Regards,
Chris.
On 2017-02-11 18:08, Doug Ingham wrote:
On 11 February 2017 at 13:32, Bartosiak-Jentys, Chris
<chris.bartosiak-jentys(a)certico.co.uk> wrote:
> Hello list,
>
> Just wanted to get your opinion on my ovirt home lab setup. While this is not a
production setup I would like it to run relatively reliably so please tell me if the
following storage configuration is likely to result in corruption or just bat s**t
insane.
>
> I have a 3 node hosted engine setup, VM data store and engine data store are both
replica 3 gluster volumes (one brick on each host).
> I do not want to run all 3 hosts 24/7 due to electricity costs, I only power up the
larger hosts (2 Dell R710's) when I need additional resources for VM's.
>
> I read about using CTDB and floating/virtual IP's to allow the storage mount
point to transition between available hosts but after some thought decided to go about
this another, simpler, way:
>
> I created a common hostname for the storage mount points: gfs-data and gfs-engine
>
> On each host I edited /etc/hosts file to have these hostnames resolve to each hosts
IP i.e. on host1 gfs-data & gfs-engine --> host1 IP
> on host2 gfs-data & gfs-engine --> host2 IP
> etc.
>
> In ovirt engine each storage domain is mounted as gfs-data:/data and
gfs-engine:/engine
> My thinking is that this way no matter which host is up and acting as SPM it will be
able to mount the storage as its only dependent on that host being up.
>
> I changed gluster options for server-quorum-ratio so that the volumes remain up even
if quorum is not met, I know this is risky but its just a lab setup after all.
>
> So, any thoughts on the /etc/hosts method to ensure the storage mount point is always
available? Is data corruption more or less inevitable with this setup? Am I insane ;) ?
Why not just use localhost? And no need for CTDB with a floating IP, oVirt uses libgfapi
for Gluster which deals with that all natively.
As for the quorum issue, I would most definitely *not* run with quorum disabled when
you're running more than one node. As you say you specifically plan for when the other
2 nodes of the replica 3 set will be active or not, I'd do something along the lines
of the following...
Going from 3 nodes to 1 node:
- Put nodes 2 & 3 in maintenance to offload their virtual load;
- Once the 2 nodes are free of load, disable quorum on the Gluster volumes;
- Power down the 2 nodes.
Going from 1 node to 3 nodes:
- Power on *only* 1 of the pair of nodes (if you power on both & self-heal is
enabled, Gluster will "heal" the files on the main node with the older files on
the 2 nodes which were powered down);
- Allow Gluster some time to detect that the files are in split-brain;
- Tell Gluster to heal the files in split-brain based on modification time;
- Once the 2 nodes are in sync, re-enable quorum & power on the last node, which will
be resynchronised automatically;
- Take the 2 hosts out of maintenance mode.
If you want to power on the 2nd two nodes at the same time, make absolutely sure
self-heal is disabled first! If you don't, Gluster will see the 2nd two nodes as in
quorum & heal the data on your 1st node with the out-of-date data.
--
Doug
--
Chris Bartosiak-Jentys
Certico
Tel: 03333 444 884
Mob: 077 0246 8132
e-mail: chris(a)certico.co.uk
www.certico.co.uk [1]
-------------------------
Confidentiality Notice: the information contained in this email and any
attachments may be legally privileged and confidential.
If you are not an intended recipient, you are hereby notified that any
dissemination, distribution, or copying of this e-mail is strictly
prohibited.
If you have received this e-mail in error, please notify the sender and
permanently delete the e-mail and any attachments immediately.
You should not retain, copy or use this e-mail or any attachments for
any purpose, nor disclose all or any part of the contents to any other
person.
Certico is a trading name of "Certico Trading Limited" England & Wales
registered company no. 5819172.
Links:
------
[1] https://www.certico.co.uk
--=_a529982ddfb8bfce09fad28eff29c930
Content-Transfer-Encoding: quoted-printable
Content-Type: text/html; charset=UTF-8
<html><head><meta http-equiv=3D"Content-Type"
content=3D"text/html; charset=
=3DUTF-8" /></head><body style=3D'font-size: 10pt; font-family:
Helvetica,A=
rial,sans-serif'>
<p>Thank you for your reply Doug,</p>
<p>I didn't use localhost as I was preparing to follow instructions (blog p=
ost: <a href=3D"http://community.redhat.com/blog/2014/11/up-and-runnin=
g-with-ovirt-3-5-part-two/)">http://community.redhat.com/blog/201...
d-running-with-ovirt-3-5-part-two/)</a> for setting up CTDB and had a=
lready created hostnames for the floating IP when I decided to ditch that a=
nd go with the hosts file hack. I already had the volumes mounted on those =
hostnames but you are absolutely right, simply using localhost would be the=
best option.</p>
<p>Thank you for your suggested outline of how to power up/down the cluster=
, I hadn't considered the fact that turning on two out of date nodes would =
clobber data on the new node. This is something I will need to be very care=
ful to avoid. The setup is mostly for lab work so not really mission critic=
al but I do run a few VM's (freeIPA, GitLab and pfSense) that I'd like to k=
eep up 24/7. I make regular backups (outside of ovirt) of those just in cas=
e.</p>
<p>Thanks, I will do some reading on how gluster handles quorum and heal op=
erations but your procedure sounds like a sensible way to operate this clus=
ter.</p>
<p>Regards,</p>
<p>Chris.</p>
<p><br /></p>
<p>On 2017-02-11 18:08, Doug Ingham wrote:</p>
<blockquote type=3D"cite" style=3D"padding: 0 0.4em; border-left:
#1010ff 2=
px solid; margin: 0"><!-- html ignored --><!-- head ignored --><!--
meta ig=
nored -->
<div dir=3D"ltr"><br />
<div class=3D"gmail_extra"><br />
<div class=3D"gmail_quote">On 11 February 2017 at 13:32, Bartosiak-Jentys,
=
Chris <span><<a
href=3D"mailto:chris.bartosiak-jentys@certico.co.uk">chr=
is.bartosiak-jentys(a)certico.co.uk</a>&gt;</span> wrote:<br />
<blockquote class=3D"gmail_quote" style=3D"margin: 0 0 0 .8ex;
border-left:=
1px #ccc solid; padding-left: 1ex;">Hello list,<br /> <br /> Just
wanted t=
o get your opinion on my ovirt home lab setup. While this is not a producti=
on setup I would like it to run relatively reliably so please tell me if th=
e following storage configuration is likely to result in corruption or just=
bat s**t insane.<br /> <br /> I have a 3 node hosted engine setup, VM data=
store and engine data store are both replica 3 gluster volumes (one brick =
on each host).<br /> I do not want to run all 3 hosts 24/7 due to electrici=
ty costs, I only power up the larger hosts (2 Dell R710's) when I need addi=
tional resources for VM's.<br /> <br /> I read about using CTDB and
floatin=
g/virtual IP's to allow the storage mount point to transition between avail=
able hosts but after some thought decided to go about this another, simpler=
, way:<br /> <br /> I created a common hostname for the storage mount point=
s: gfs-data and gfs-engine<br /> <br /> On each host I edited /etc/hosts fi=
le to have these hostnames resolve to each hosts IP i.e. on host1 gfs-data =
& gfs-engine --> host1 IP<br /> on host2 gfs-data &
gfs-engine -=
-> host2 IP<br /> etc.<br /> <br /> In ovirt engine each storage
domain =
is mounted as gfs-data:/data and gfs-engine:/engine<br /> My thinking is th=
at this way no matter which host is up and acting as SPM it will be able to=
mount the storage as its only dependent on that host being up.<br /> <br /=
I changed gluster options for server-quorum-ratio so that the volumes
rem=
ain up even if quorum is not met, I know this is risky but its just a lab s=
etup after all.<br /> <br /> So, any thoughts on the /etc/hosts method to e=
nsure the storage mount point is always available? Is data corruption more =
or less inevitable with this setup? Am I insane ;) ?</blockquote>
<div> </div>
<div>Why not just use localhost? And no need for CTDB with a floating IP, o=
Virt uses libgfapi for Gluster which deals with that all natively.</div>
<div><br />As for the quorum issue, I would most definitely *not* run with =
quorum disabled when you're running more than one node. As you say you spec=
ifically plan for when the other 2 nodes of the replica 3 set will be activ=
e or not, I'd do something along the lines of the following...<br /><br
/><=
/div>
<div>Going from 3 nodes to 1 node:</div>
<div> - Put nodes 2 & 3 in maintenance to offload their virtual
lo=
ad;</div>
<div> - Once the 2 nodes are free of load, disable quorum on the Glust=
er volumes;</div>
<div> - Power down the 2 nodes.<br /><br /></div>
<div>Going from 1 node to 3 nodes:</div>
<div> - Power on *only* 1 of the pair of nodes (if you power on both
&=
amp; self-heal is enabled, Gluster will "heal" the files on the main node w=
ith the older files on the 2 nodes which were powered down);</div>
<div> - Allow Gluster some time to detect that the files are in split-=
brain;</div>
<div> - Tell Gluster to heal the files in split-brain based on modific=
ation time;</div>
<div> - Once the 2 nodes are in sync, re-enable quorum & power on
=
the last node, which will be resynchronised automatically;</div>
<div> - Take the 2 hosts out of maintenance mode.</div>
<div> </div>
<div>If you want to power on the 2nd two nodes at the same time, make absol=
utely sure self-heal is disabled first! If you don't, Gluster will see the =
2nd two nodes as in quorum & heal the data on your 1st node with the ou=
t-of-date data.</div>
</div>
<br clear=3D"all" /><br />-- <br />
<div class=3D"gmail_signature">Doug</div>
</div>
</div>
</blockquote>
<div>-- <br />
<div class=3D"pre" style=3D"margin: 0; padding: 0; font-family:
monospace">
<pre><span style=3D"font-family: arial,helvetica,sans-serif;">Chris
Bartosi=
ak-Jentys<br />Certico<br />Tel: 03333 444 884<br />Mob: 077 0246 8132
<br =
/>e-mail: <a
href=3D"mailto:chris@certico.co.uk">chris@certico.co.uk</a> <b=
r /><a
href=3D"https://www.certico.co.uk">www.certico.co.uk</a><br
/><br />=
</span></pre>
<hr />
<pre><span style=3D"font-family:
arial,helvetica,sans-serif;">Confidentiali=
ty Notice: the information contained in this email and any attachments may =
be legally privileged and confidential.<br />If you are not an intended rec=
ipient, you are hereby notified that any dissemination, distribution, or co=
pying of this e-mail is strictly prohibited.<br />If you have received this=
e-mail in error, please notify the sender and permanently delete the e-mai=
l and any attachments immediately.<br />You should not retain, copy or use =
this e-mail or any attachments for any purpose, nor disclose all or any par=
t of the contents to any other person. <br />Certico is a trading name of "=
Certico Trading Limited" England & Wales registered company no. 5819172=
=2E</span></pre>
</div>
</div>
</body></html>
--=_a529982ddfb8bfce09fad28eff29c930--
1:18 p.m.
On 11 February 2017 at 15:39, Bartosiak-Jentys, Chris <
chris.bartosiak-jentys(a)certico.co.uk> wrote:
Thank you for your reply Doug,
I didn't use localhost as I was preparing to follow instructions (blog
post: http://community.redhat.com/blog/2014/11/up-and-
running-with-ovirt-3-5-part-two/) for setting up CTDB and had already
created hostnames for the floating IP when I decided to ditch that and go
with the hosts file hack. I already had the volumes mounted on those
hostnames but you are absolutely right, simply using localhost would be the
best option.
oVirt 3.5? 2014? That's oooold. Both oVirt & Gluster have moved on a lot
since then. I would strongly recommend studying Gluster's documentation
before implementing it in production. It's not complicated, but you have to
have a good understanding of what you're doing & why if you want to protect
the integrity of your data & avoid waking up one day to find everything in
meltdown.
https://gluster.readthedocs.io/en/latest/
Red Hat's portal is also very good & full of detailed tips for tuning your
setup, however their "stable" versions (which they have to support) are of
course much older than the project's own latest stable, so keep this in
mind when considering their advice.
https://access.redhat.com/documentation/en/red-hat-storage/
Likewise with their oVirt documentation, although their supported oVirt
versions are much closer to the current stable release. It also features a
lot of very good advice for configuring & tuning an oVirt (RHEV) &
GlusterFS (RHGS) hyperconverged setup.
https://access.redhat.com/documentation/en/red-hat-virtualization/
For any other Gluster specific questions, you can usually get good & timely
responses on their mailing list & IRC channel.
Thank you for your suggested outline of how to power up/down the cluster, I
hadn't considered the fact that turning on two out of date nodes
would
clobber data on the new node. This is something I will need to be very
careful to avoid. The setup is mostly for lab work so not really mission
critical but I do run a few VM's (freeIPA, GitLab and pfSense) that I'd
like to keep up 24/7. I make regular backups (outside of ovirt) of those
just in case.
Thanks, I will do some reading on how gluster handles quorum and heal
operations but your procedure sounds like a sensible way to operate this
cluster.
Regards,
Chris.
On 2017-02-11 18:08, Doug Ingham wrote:
On 11 February 2017 at 13:32, Bartosiak-Jentys, Chris <
chris.bartosiak-jentys(a)certico.co.uk> wrote:
> Hello list,
>
> Just wanted to get your opinion on my ovirt home lab setup. While this is
> not a production setup I would like it to run relatively reliably so please
> tell me if the following storage configuration is likely to result in
> corruption or just bat s**t insane.
>
> I have a 3 node hosted engine setup, VM data store and engine data store
> are both replica 3 gluster volumes (one brick on each host).
> I do not want to run all 3 hosts 24/7 due to electricity costs, I only
> power up the larger hosts (2 Dell R710's) when I need additional resources
> for VM's.
>
> I read about using CTDB and floating/virtual IP's to allow the storage
> mount point to transition between available hosts but after some thought
> decided to go about this another, simpler, way:
>
> I created a common hostname for the storage mount points: gfs-data and
> gfs-engine
>
> On each host I edited /etc/hosts file to have these hostnames resolve to
> each hosts IP i.e. on host1 gfs-data & gfs-engine --> host1 IP
> on host2 gfs-data & gfs-engine --> host2 IP
> etc.
>
> In ovirt engine each storage domain is mounted as gfs-data:/data and
> gfs-engine:/engine
> My thinking is that this way no matter which host is up and acting as SPM
> it will be able to mount the storage as its only dependent on that host
> being up.
>
> I changed gluster options for server-quorum-ratio so that the volumes
> remain up even if quorum is not met, I know this is risky but its just a
> lab setup after all.
>
> So, any thoughts on the /etc/hosts method to ensure the storage mount
> point is always available? Is data corruption more or less inevitable with
> this setup? Am I insane ;) ?
Why not just use localhost? And no need for CTDB with a floating IP, oVirt
uses libgfapi for Gluster which deals with that all natively.
As for the quorum issue, I would most definitely *not* run with quorum
disabled when you're running more than one node. As you say you
specifically plan for when the other 2 nodes of the replica 3 set will be
active or not, I'd do something along the lines of the following...
Going from 3 nodes to 1 node:
- Put nodes 2 & 3 in maintenance to offload their virtual load;
- Once the 2 nodes are free of load, disable quorum on the Gluster
volumes;
- Power down the 2 nodes.
Going from 1 node to 3 nodes:
- Power on *only* 1 of the pair of nodes (if you power on both &
self-heal is enabled, Gluster will "heal" the files on the main node with
the older files on the 2 nodes which were powered down);
- Allow Gluster some time to detect that the files are in split-brain;
- Tell Gluster to heal the files in split-brain based on modification
time;
- Once the 2 nodes are in sync, re-enable quorum & power on the last
node, which will be resynchronised automatically;
- Take the 2 hosts out of maintenance mode.
If you want to power on the 2nd two nodes at the same time, make
absolutely sure self-heal is disabled first! If you don't, Gluster will see
the 2nd two nodes as in quorum & heal the data on your 1st node with the
out-of-date data.
--
Doug
--
Chris Bartosiak-Jentys
Certico
Tel: 03333 444 884
Mob: 077 0246 8132
e-mail: chris(a)certico.co.uk
www.certico.co.uk
------------------------------
Confidentiality Notice: the information contained in this email and any attachments may
be legally privileged and confidential.
If you are not an intended recipient, you are hereby notified that any dissemination,
distribution, or copying of this e-mail is strictly prohibited.
If you have received this e-mail in error, please notify the sender and permanently
delete the e-mail and any attachments immediately.
You should not retain, copy or use this e-mail or any attachments for any purpose, nor
disclose all or any part of the contents to any other person.
Certico is a trading name of "Certico Trading Limited" England & Wales
registered company no. 5819172.
--
Doug
On 11 February 2017 at 15:39, Bartosiak-Jentys, Chris <
chris.bartosiak-jentys(a)certico.co.uk> wrote:
Thank you for your reply Doug,
I didn't use localhost as I was preparing to follow instructions (blog
post: http://community.redhat.com/blog/2014/11/up-and-
running-with-ovirt-3-5-part-two/) for setting up CTDB and had already
created hostnames for the floating IP when I decided to ditch that and go
with the hosts file hack. I already had the volumes mounted on those
hostnames but you are absolutely right, simply using localhost would be the
best option.
> Thank you for your suggested outline of how to power up/down the cluster,
> I hadn't considered the fact that turning on two out of date nodes would
> clobber data on the new node. This is something I will need to be very
> careful to avoid. The setup is mostly for lab work so not really mission
> critical but I do run a few VM's (freeIPA, GitLab and pfSense) that I'd
> like to keep up 24/7. I make regular backups (outside of ovirt) of those
> just in case.
>
> Thanks, I will do some reading on how gluster handles quorum and heal
> operations but your procedure sounds like a sensible way to operate this
> cluster.
>
> Regards,
>
> Chris.
>
>
> On 2017-02-11 18:08, Doug Ingham wrote:
>
>
>
> On 11 February 2017 at 13:32, Bartosiak-Jentys, Chris <
> chris.bartosiak-jentys(a)certico.co.uk> wrote:
>
>> Hello list,
>>
>> Just wanted to get your opinion on my ovirt home lab setup. While this is
>> not a production setup I would like it to run relatively reliably so please
>> tell me if the following storage configuration is likely to result in
>> corruption or just bat s**t insane.
>>
>> I have a 3 node hosted engine setup, VM data store and engine data store
>> are both replica 3 gluster volumes (one brick on each host).
>> I do not want to run all 3 hosts 24/7 due to electricity costs, I only
>> power up the larger hosts (2 Dell R710's) when I need additional resources
>> for VM's.
>>
>> I read about using CTDB and floating/virtual IP's to allow the storage
>> mount point to transition between available hosts but after some thought
>> decided to go about this another, simpler, way:
>>
>> I created a common hostname for the storage mount points: gfs-data and
>> gfs-engine
>>
>> On each host I edited /etc/hosts file to have these hostnames resolve to
>> each hosts IP i.e. on host1 gfs-data & gfs-engine --> host1 IP
>> on host2 gfs-data & gfs-engine --> host2 IP
>> etc.
>>
>> In ovirt engine each storage domain is mounted as gfs-data:/data and
>> gfs-engine:/engine
>> My thinking is that this way no matter which host is up and acting as SPM
>> it will be able to mount the storage as its only dependent on that host
>> being up.
>>
>> I changed gluster options for server-quorum-ratio so that the volumes
>> remain up even if quorum is not met, I know this is risky but its just a
>> lab setup after all.
>>
>> So, any thoughts on the /etc/hosts method to ensure the storage mount
>> point is always available? Is data corruption more or less inevitable with
>> this setup? Am I insane ;) ?
>
>
> Why not just use localhost? And no need for CTDB with a floating IP, oVirt
> uses libgfapi for Gluster which deals with that all natively.
>
> As for the quorum issue, I would most definitely *not* run with quorum
> disabled when you're running more than one node. As you say you
> specifically plan for when the other 2 nodes of the replica 3 set will be
> active or not, I'd do something along the lines of the following...
>
> Going from 3 nodes to 1 node:
> - Put nodes 2 & 3 in maintenance to offload their virtual load;
> - Once the 2 nodes are free of load, disable quorum on the Gluster
> volumes;
> - Power down the 2 nodes.
>
> Going from 1 node to 3 nodes:
> - Power on *only* 1 of the pair of nodes (if you power on both &
> self-heal is enabled, Gluster will "heal" the files on the main node with
> the older files on the 2 nodes which were powered down);
> - Allow Gluster some time to detect that the files are in split-brain;
> - Tell Gluster to heal the files in split-brain based on modification
> time;
> - Once the 2 nodes are in sync, re-enable quorum & power on the last
> node, which will be resynchronised automatically;
> - Take the 2 hosts out of maintenance mode.
>
> If you want to power on the 2nd two nodes at the same time, make
> absolutely sure self-heal is disabled first! If you don't, Gluster will see
> the 2nd two nodes as in quorum & heal the data on your 1st node with the
> out-of-date data.
>
>
> --
> Doug
>
> --
>
> Chris Bartosiak-Jentys
> Certico
> Tel: 03333 444 884
> Mob: 077 0246 8132
> e-mail: chris(a)certico.co.uk
> www.certico.co.uk
>
> ------------------------------
>
> Confidentiality Notice: the information contained in this email and any attachments
may be legally privileged and confidential.
> If you are not an intended recipient, you are hereby notified that any dissemination,
distribution, or copying of this e-mail is strictly prohibited.
> If you have received this e-mail in error, please notify the sender and permanently
delete the e-mail and any attachments immediately.
> You should not retain, copy or use this e-mail or any attachments for any purpose,
nor disclose all or any part of the contents to any other person.
> Certico is a trading name of "Certico Trading Limited" England & Wales
registered company no. 5819172.
>
>
--
Doug
1:29 p.m.
Thanks for the links, I will add them to my reading list. Absolutely
would read the docs before deploying ovirt in production and definitely
would not use this storage configuration, this is purely to keep from
wasting electricity.
Chris.
On 2017-02-11 19:18, Doug Ingham wrote:
On 11 February 2017 at 15:39, Bartosiak-Jentys, Chris
<chris.bartosiak-jentys(a)certico.co.uk> wrote:
> Thank you for your reply Doug,
>
> I didn't use localhost as I was preparing to follow instructions (blog
> post:
> http://community.redhat.com/blog/2014/11/up-and-running-with-ovirt-3-5-pa...)
> for setting up CTDB and had already created hostnames for the
> floating IP when I decided to ditch that and go with the hosts file
> hack. I already had the volumes mounted on those hostnames but you are
> absolutely right, simply using localhost would be the best option.
oVirt 3.5? 2014? That's oooold. Both oVirt & Gluster have moved on a
lot since then. I would strongly recommend studying Gluster's
documentation before implementing it in production. It's not
complicated, but you have to have a good understanding of what you're
doing & why if you want to protect the integrity of your data & avoid
waking up one day to find everything in meltdown.
https://gluster.readthedocs.io/en/latest/
Red Hat's portal is also very good & full of detailed tips for tuning
your setup, however their "stable" versions (which they have to
support) are of course much older than the project's own latest stable,
so keep this in mind when considering their advice.
https://access.redhat.com/documentation/en/red-hat-storage/
Likewise with their oVirt documentation, although their supported oVirt
versions are much closer to the current stable release. It also
features a lot of very good advice for configuring & tuning an oVirt
(RHEV) & GlusterFS (RHGS) hyperconverged setup.
https://access.redhat.com/documentation/en/red-hat-virtualization/
For any other Gluster specific questions, you can usually get good &
timely responses on their mailing list & IRC channel.
Thank you for your suggested outline of how to power up/down the
cluster, I hadn't considered the fact that turning on two out of date
nodes would clobber data on the new node. This is something I will need
to be very careful to avoid. The setup is mostly for lab work so not
really mission critical but I do run a few VM's (freeIPA, GitLab and
pfSense) that I'd like to keep up 24/7. I make regular backups (outside
of ovirt) of those just in case.
Thanks, I will do some reading on how gluster handles quorum and heal
operations but your procedure sounds like a sensible way to operate
this cluster.
Regards,
Chris.
On 2017-02-11 18:08, Doug Ingham wrote:
On 11 February 2017 at 13:32, Bartosiak-Jentys, Chris
<chris.bartosiak-jentys(a)certico.co.uk> wrote:
Hello list,
Just wanted to get your opinion on my ovirt home lab setup. While this
is not a production setup I would like it to run relatively reliably so
please tell me if the following storage configuration is likely to
result in corruption or just bat s**t insane.
I have a 3 node hosted engine setup, VM data store and engine data
store are both replica 3 gluster volumes (one brick on each host).
I do not want to run all 3 hosts 24/7 due to electricity costs, I only
power up the larger hosts (2 Dell R710's) when I need additional
resources for VM's.
I read about using CTDB and floating/virtual IP's to allow the storage
mount point to transition between available hosts but after some
thought decided to go about this another, simpler, way:
I created a common hostname for the storage mount points: gfs-data and
gfs-engine
On each host I edited /etc/hosts file to have these hostnames resolve
to each hosts IP i.e. on host1 gfs-data & gfs-engine --> host1 IP
on host2 gfs-data & gfs-engine --> host2 IP
etc.
In ovirt engine each storage domain is mounted as gfs-data:/data and
gfs-engine:/engine
My thinking is that this way no matter which host is up and acting as
SPM it will be able to mount the storage as its only dependent on that
host being up.
I changed gluster options for server-quorum-ratio so that the volumes
remain up even if quorum is not met, I know this is risky but its just
a lab setup after all.
So, any thoughts on the /etc/hosts method to ensure the storage mount
point is always available? Is data corruption more or less inevitable
with this setup? Am I insane ;) ?
Why not just use localhost? And no need for CTDB with a floating IP,
oVirt uses libgfapi for Gluster which deals with that all natively.
As for the quorum issue, I would most definitely *not* run with quorum
disabled when you're running more than one node. As you say you
specifically plan for when the other 2 nodes of the replica 3 set will
be active or not, I'd do something along the lines of the following...
Going from 3 nodes to 1 node:
- Put nodes 2 & 3 in maintenance to offload their virtual load;
- Once the 2 nodes are free of load, disable quorum on the Gluster
volumes;
- Power down the 2 nodes.
Going from 1 node to 3 nodes:
- Power on *only* 1 of the pair of nodes (if you power on both &
self-heal is enabled, Gluster will "heal" the files on the main node
with the older files on the 2 nodes which were powered down);
- Allow Gluster some time to detect that the files are in split-brain;
- Tell Gluster to heal the files in split-brain based on modification
time;
- Once the 2 nodes are in sync, re-enable quorum & power on the last
node, which will be resynchronised automatically;
- Take the 2 hosts out of maintenance mode.
If you want to power on the 2nd two nodes at the same time, make
absolutely sure self-heal is disabled first! If you don't, Gluster will
see the 2nd two nodes as in quorum & heal the data on your 1st node
with the out-of-date data.
--
Doug
--
Chris Bartosiak-Jentys
Certico
Tel: 03333 444 884
Mob: 077 0246 8132
e-mail: chris(a)certico.co.uk
www.certico.co.uk
-------------------------
Confidentiality Notice: the information contained in this email and any
attachments may be legally privileged and confidential.
If you are not an intended recipient, you are hereby notified that any
dissemination, distribution, or copying of this e-mail is strictly
prohibited.
If you have received this e-mail in error, please notify the sender and
permanently delete the e-mail and any attachments immediately.
You should not retain, copy or use this e-mail or any attachments for
any purpose, nor disclose all or any part of the contents to any other
person.
Certico is a trading name of "Certico Trading Limited" England & Wales
registered company no. 5819172.
--
Doug
On 11 February 2017 at 15:39, Bartosiak-Jentys, Chris
<chris.bartosiak-jentys(a)certico.co.uk> wrote:
Thank you for your reply Doug,
I didn't use localhost as I was preparing to follow instructions (blog
post:
http://community.redhat.com/blog/2014/11/up-and-running-with-ovirt-3-5-pa...)
for setting up CTDB and had already created hostnames for the floating
IP when I decided to ditch that and go with the hosts file hack. I
already had the volumes mounted on those hostnames but you are
absolutely right, simply using localhost would be the best option.
Thank you for your suggested outline of how to power up/down the
cluster, I hadn't considered the fact that turning on two out of date
nodes would clobber data on the new node. This is something I will need
to be very careful to avoid. The setup is mostly for lab work so not
really mission critical but I do run a few VM's (freeIPA, GitLab and
pfSense) that I'd like to keep up 24/7. I make regular backups (outside
of ovirt) of those just in case.
Thanks, I will do some reading on how gluster handles quorum and heal
operations but your procedure sounds like a sensible way to operate
this cluster.
Regards,
Chris.
On 2017-02-11 18:08, Doug Ingham wrote:
On 11 February 2017 at 13:32, Bartosiak-Jentys, Chris
<chris.bartosiak-jentys(a)certico.co.uk> wrote:
Hello list,
Just wanted to get your opinion on my ovirt home lab setup. While this
is not a production setup I would like it to run relatively reliably so
please tell me if the following storage configuration is likely to
result in corruption or just bat s**t insane.
I have a 3 node hosted engine setup, VM data store and engine data
store are both replica 3 gluster volumes (one brick on each host).
I do not want to run all 3 hosts 24/7 due to electricity costs, I only
power up the larger hosts (2 Dell R710's) when I need additional
resources for VM's.
I read about using CTDB and floating/virtual IP's to allow the storage
mount point to transition between available hosts but after some
thought decided to go about this another, simpler, way:
I created a common hostname for the storage mount points: gfs-data and
gfs-engine
On each host I edited /etc/hosts file to have these hostnames resolve
to each hosts IP i.e. on host1 gfs-data & gfs-engine --> host1 IP
on host2 gfs-data & gfs-engine --> host2 IP
etc.
In ovirt engine each storage domain is mounted as gfs-data:/data and
gfs-engine:/engine
My thinking is that this way no matter which host is up and acting as
SPM it will be able to mount the storage as its only dependent on that
host being up.
I changed gluster options for server-quorum-ratio so that the volumes
remain up even if quorum is not met, I know this is risky but its just
a lab setup after all.
So, any thoughts on the /etc/hosts method to ensure the storage mount
point is always available? Is data corruption more or less inevitable
with this setup? Am I insane ;) ?
Why not just use localhost? And no need for CTDB with a floating IP,
oVirt uses libgfapi for Gluster which deals with that all natively.
As for the quorum issue, I would most definitely *not* run with quorum
disabled when you're running more than one node. As you say you
specifically plan for when the other 2 nodes of the replica 3 set will
be active or not, I'd do something along the lines of the following...
Going from 3 nodes to 1 node:
- Put nodes 2 & 3 in maintenance to offload their virtual load;
- Once the 2 nodes are free of load, disable quorum on the Gluster
volumes;
- Power down the 2 nodes.
Going from 1 node to 3 nodes:
- Power on *only* 1 of the pair of nodes (if you power on both &
self-heal is enabled, Gluster will "heal" the files on the main node
with the older files on the 2 nodes which were powered down);
- Allow Gluster some time to detect that the files are in split-brain;
- Tell Gluster to heal the files in split-brain based on modification
time;
- Once the 2 nodes are in sync, re-enable quorum & power on the last
node, which will be resynchronised automatically;
- Take the 2 hosts out of maintenance mode.
If you want to power on the 2nd two nodes at the same time, make
absolutely sure self-heal is disabled first! If you don't, Gluster will
see the 2nd two nodes as in quorum & heal the data on your 1st node
with the out-of-date data.
--
Doug
2989
days inactive
2989
days old
4 comments
2 participants
participants (2)
-
Bartosiak-Jentys, Chris -
Doug Ingham