10:38 p.m.
I’m trying to upload an ISO image in ovirt 4.4.10, It’s been a huge challenge to
accomplish this. I read several post regarding this issue, I really don’t have s clear
understanding of solution to this issue. My experience has not been very fruitful at all.
When I try to perform the upload using the web GUI I get the following message in the
status column: “Paused by System“. I’ve been reading for roughly three weeks trying to
understand and resolve the issue. There is a tremendous amount of discussion centered
around changing certificate file located in the directory “etcpki/ovirt-engine”, however
it not clear at all what files need to change.
My installation is an out-of-box installation with any certificates beginning generated as
part of the install process, I’ve imported the certificate that was generated into my
browser/Firefox 91.9.0. Based on what I’ve been reading the solution to my problems is
that the certificate does not match the certificate defined in the “imageio-service”, my
question is why because it was generated as part of the installation?
What files in the “/etc/pki/ovirt-engine” must be changed to get things working. Further
should or do I copy the certificate saved from the GUI to files under
“/etc/pki/ovirt-engine” directory?
I feel like I’m so close after six month of reading and re-installs, what do I do next?
Thanks
8:32 a.m.
On Mon, May 9, 2022 at 10:40 PM <louisb(a)ameritech.net> wrote:
I’m trying to upload an ISO image in ovirt 4.4.10, It’s been a huge challenge to
accomplish this. I read several post regarding this issue, I really don’t have s clear
understanding of solution to this issue. My experience has not been very fruitful at
all.
When I try to perform the upload using the web GUI I get the following message in the
status column: “Paused by System“. I’ve been reading for roughly three weeks trying to
understand and resolve the issue. There is a tremendous amount of discussion centered
around changing certificate file located in the directory “etcpki/ovirt-engine”, however
it not clear at all what files need to change.
My installation is an out-of-box installation with any certificates beginning generated
as part of the install process, I’ve imported the certificate that was generated into my
browser/Firefox 91.9.0.
Which one, and how?
You should import the CA Cert, and trust it for web sites.
Best regards,
Based on what I’ve been reading the solution to my problems is that
the certificate does not match the certificate defined in the “imageio-service”, my
question is why because it was generated as part of the installation?
What files in the “/etc/pki/ovirt-engine” must be changed to get things working. Further
should or do I copy the certificate saved from the GUI to files under
“/etc/pki/ovirt-engine” directory?
I feel like I’m so close after six month of reading and re-installs, what do I do next?
Thanks
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/YVGGVNOQ5FL...
--
Didi
1:18 p.m.
On Mon, May 9, 2022 at 10:40 PM <louisb(a)ameritech.net> wrote:
I’m trying to upload an ISO image in ovirt 4.4.10, It’s been a huge challenge to
accomplish this. I read several post regarding this issue, I really don’t have s clear
understanding of solution to this issue. My experience has not been very fruitful at all.
Sorry to hear this.
When I try to perform the upload using the web GUI I get the
following message in the status column: “Paused by System“. I’ve been reading for roughly
three weeks trying to understand and resolve the issue. There is a tremendous amount of
discussion centered around changing certificate file located in the directory
“etcpki/ovirt-engine”, however it not clear at all what files need to change.
My installation is an out-of-box installation with any certificates beginning generated
as part of the install process, I’ve imported the certificate that was generated into my
browser/Firefox 91.9.0. Based on what I’ve been reading the solution to my problems is
that the certificate does not match the certificate defined in the “imageio-service”, my
question is why because it was generated as part of the installation?
If your system is out-of-box installation and you are using the
default self signed
engine CA, there should be no mismatch.
What files in the “/etc/pki/ovirt-engine” must be changed to get
things working. Further should or do I copy the certificate saved from the GUI to files
under “/etc/pki/ovirt-engine” directory?
You don't have to change anything to use the defaults.
I feel like I’m so close after six month of reading and re-installs,
what do I do next?
There is not enough info in you mail what you tried to do, and or any
logs showing
what the system did. To make sure you installed the certificate
properly, this is
the way to import the engine CA certificate:
1. Download the certificate from:
https://myengine.example.com/ovirt-engine/services/pki-resource?resource=...
2. In Firefox settings, search "Certificates" and click "View
certificates"
3. Click "Authorities" and "Import..."
Select the certificate file, and enable the first checkbox for
trusting web sites.
4. Reopen the browser to activate the certificate
To test that the certificate works, open the "Disks" tab, and click
"Upload > Start".
Click "Test connection" - you should see a green message about
successful connection
to ovirt-imageio.
Lets continue when you reach this.
Nir
8:36 p.m.
I greatly appreciate the response, however, following you instructions I’m still not able
to upload an ISO via the GUI.
When try an upload using the GUI I follow the instruction below:
• In the pane on the left hand side of the screen, I select “Storage”.
• Select “Disks”.
• Where I get the screen “Storage > Disks”.
• On the top right hand side of the screen, I select “Upload”.
• From the pull down menu I select “Start”.
• I choose the file/ISO I want to upload, in this case its “CENTOS-Stream” version 9.
• At the bottom of the screen I click the “Test Connection” button.
• The following messages appears:
Connection to “ovirt-imageio-service” has failed. Ensure the “ovirt certificate” is
registered as a valid CA in the browser.
• I click/select the “ovirt certificate” which is highlighted in blue on my screen.
• It displays the option to save the certificate or view it in the browser. My
browser is Firefox 91.9.0.
• I save the certificate which I later import into my browser (following your
instruction). The certificate is accepted by the browser with no errors encountered.
• I then restart the upload process again and “Test Connection”. The same message is
displayed:
Connection to “ovirt-imageio-service” has failed. Ensure the “ovirt certificate” is
registered as a valid CA in the browser. The same message as earlier in the process.
9:51 p.m.
On Tue, May 10, 2022 at 8:37 PM <louisb(a)ameritech.net> wrote:
I greatly appreciate the response, however, following you instructions I’m still not able
to upload an ISO via the GUI.
When try an upload using the GUI I follow the instruction below:
• In the pane on the left hand side of the screen, I select “Storage”.
• Select “Disks”.
• Where I get the screen “Storage > Disks”.
• On the top right hand side of the screen, I select “Upload”.
• From the pull down menu I select “Start”.
• I choose the file/ISO I want to upload, in this case its “CENTOS-Stream” version
9.
• At the bottom of the screen I click the “Test Connection” button.
• The following messages appears:
Connection to “ovirt-imageio-service” has failed. Ensure the “ovirt certificate” is
registered as a valid CA in the browser.
• I click/select the “ovirt certificate” which is highlighted in blue on my screen.
• It displays the option to save the certificate or view it in the browser. My
browser is Firefox 91.9.0.
• I save the certificate which I later import into my browser (following your
instruction). The certificate is accepted by the browser with no errors encountered.
• I then restart the upload process again and “Test Connection”. The same message
is displayed:
Connection to “ovirt-imageio-service” has failed. Ensure the “ovirt certificate” is
registered as a valid CA in the browser. The same message as earlier in the process.
Great, the issue is clear now - your browser cannot access ovirt-imageio service
since the browser likey does not have the certificate, or maybe ovirt-imageio is
misconfigured in some way.
To make sure you imported the certificate in the browser - when you
access the engine,
do you get a warning about an insecure site?
For example in my Firefox (100.0, Fedora 35) I see a secure
connection, see screenshots.
If you have the certificate, we need to understand why the browser
cannot connect
to imageio service.
One reason is installing ovirt on a single host, and adding the *same*
host to engine
a hypervisor. This setup was called "all-in-one" and was deprecated
few years ago
and is not officially supported - but it can work if you modify engine
configuration.
If you have this kind of installation, you need to disable the imageio
proxy in engine
configuration:
engine-config -s ImageTransferProxyEnabled=false
And restart ovirt-engine service. Upload should work after this change.
If your engine is not running on your single host, we need to understand why
the imageio service does not recognize the certificate.
Please share output of:
ovirt-imageio --show-config
ls -lh /etc/pki/ovirt-engine/apache-ca.pem
Here are example values from my system - regular engine install using defaults:
$ ovirt-imageio --show-config
...
"control": {
"port": 54324,
"prefer_ipv4": true,
"remove_timeout": 60,
"socket": "/run/ovirt-imageio/sock",
"transport": "tcp"
},
...
"remote": {
"host": "::",
"port": 54323
},
"tls": {
"ca_file": "/etc/pki/ovirt-engine/apache-ca.pem",
"cert_file": "/etc/pki/ovirt-engine/certs/apache.cer",
"enable": true,
"enable_tls1_1": false,
"key_file": "/etc/pki/ovirt-engine/keys/apache.key.nopass"
}
...
$ ls -lh /etc/pki/ovirt-engine/apache-ca.pem
lrwxrwxrwx. 1 root root 28 Apr 18 00:21
/etc/pki/ovirt-engine/apache-ca.pem -> /etc/pki/ovirt-engine/ca.pem
Nir
1:27 a.m.
Made the suggestion that you made earlier I continued to get the same results. Sharing
the files/things you requested below:
ovirt-imageio --show-config
{
"backend_file": {
"buffer_size": 8388608
},
"backend_http": {
"buffer_size": 8388608,
"ca_file": "/etc/pki/ovirt-engine/ca.pem"
},
"backend_nbd": {
"buffer_size": 8388608
},
"control": {
"port": 54324,
"prefer_ipv4": true,
"remove_timeout": 60,
"socket": "/run/ovirt-imageio/sock",
"transport": "unix"
},
"daemon": {
"drop_privileges": true,
"group_name": "ovirtimg",
"max_connections": 8,
"poll_interval": 1.0,
"run_dir": "/run/ovirt-imageio",
"user_name": "ovirtimg"
},
"formatter_long": {
"format": "%(asctime)s %(levelname)-7s (%(threadName)s) [%(name)s]
%(message)s"
},
"formatters": {
"keys": "long"
},
"handler_logfile": {
"args": "(\"/var/log/ovirt-imageio/daemon.log\",)",
"formatter": "long",
"class": "logging.handlers.RotatingFileHandler",
"kwargs": "{\"maxBytes\": 20971520,
\"backupCount\": 10}",
"level": "DEBUG"
},
"handler_stderr": {
"args": "()",
"formatter": "long",
"class": "logging.StreamHandler",
"level": "DEBUG"
},
"handlers": {
"keys": "logfile"
},
"local": {
"enable": true,
"socket": "\u0000/org/ovirt/imageio"
},
"logger_root": {
"handlers": "logfile",
"level": "INFO",
"propagate": 0
},
"loggers": {
"keys": "root"
},
"profile": {
"filename": "/run/ovirt-imageio/profile"
},
"remote": {
"host": "::",
"port": 54322
},
"tls": {
"ca_file": "/etc/pki/vdsm/certs/cacert.pem",
"cert_file": "/etc/pki/vdsm/certs/vdsmcert.pem",
"enable": true,
"enable_tls1_1": false,
"key_file": "/etc/pki/vdsm/keys/vdsmkey.pem"
}
}
ls -lh /etc/pki/ovirt-engine/apache-ca.pem
lrwxrwxrwx. 1 root root 28 May 2 17:57 /etc/pki/ovirt-engine/apache-ca.pem ->
/etc/pki/ovirt-engine/ca.pem
sudo systemctl status ovirt-imageio
● ovirt-imageio.service - oVirt ImageIO Daemon
Loaded: loaded (/usr/lib/systemd/system/ovirt-imageio.service; enabled; vendor preset:
disabled)
Active: active (running) since Tue 2022-05-10 17:45:16 EDT; 12min ago
Main PID: 1564 (ovirt-imageio)
Tasks: 4 (limit: 201976)
Memory: 20.1M
CGroup: /system.slice/ovirt-imageio.service
└─1564 /usr/libexec/platform-python -s /usr/bin/ovirt-imageio
May 10 17:45:14 hpdl380gen10.cscd.net systemd[1]: Starting oVirt ImageIO Daemon...
May 10 17:45:16 hpdl380gen10.cscd.net systemd[1]: Started oVirt ImageIO Daemon.
Please tell what else I should be looking for or at?
Thanks
12:10 p.m.
On Wed, May 11, 2022 at 1:29 AM <louisb(a)ameritech.net> wrote:
Made the suggestion that you made earlier I continued to get the same results.
Sharing the files/things you requested below:
ovirt-imageio --show-config
...
"control": {
"port": 54324,
"prefer_ipv4": true,
"remove_timeout": 60,
"socket": "/run/ovirt-imageio/sock",
"transport": "unix"
},
So your ovirt-imageio service is configured for vdsm. This confirms
that your engine host is also used a hypervisor
(all-in-one deprecated configuration).
...
},
"remote": {
"host": "::",
"port": 54322
},
Since the ovirt-imageio service listen on port 54322, engine
UI should not try to connect to the proxy (port 54323). This
is done by disabling the proxy as I explained in the previous email.
"tls": {
"ca_file": "/etc/pki/vdsm/certs/cacert.pem",
"cert_file": "/etc/pki/vdsm/certs/vdsmcert.pem",
"enable": true,
"enable_tls1_1": false,
"key_file": "/etc/pki/vdsm/keys/vdsmkey.pem"
}
}
Using vdsm pki, works for all-in-one setup.
Did you run engine-config as root?
Did you restart ovirt-engine after disabling the proxy?
Just to be sure - do this and share the output:
sudo engine-config -s ImageTransferProxyEnabled=false
sudo engine-config -g ImageTransferProxyEnabled
sudo systemctl restart ovirt-engine
engine-config should report:
ImageTransferProxyEnabled: false version: general
After the engine is restarted, try the "Test connection" again from
the upload UI.
If it works, upload should also work. If not, we will have to dig deeper.
Nir
1:30 a.m.
I also noticed that I started to receive the error message below:
VDSM ovirtdl380gen10 command HSMGetAllTasksStatusesVDS failed: Not SPM: ()
Thanks
1:36 a.m.
I also started to receive the error message below after making the suggested changes:
VDSM ovirtdl380gen10 command HSMGetAllTasksStatusesVDS failed: Not SPM: ()
On my browser it indicates that there is no tracking, verified by my domain, You have
granted this website additional permission.
Thanks
12:11 p.m.
On Wed, May 11, 2022 at 1:37 AM <louisb(a)ameritech.net> wrote:
I also started to receive the error message below after making the suggested changes:
VDSM ovirtdl380gen10 command HSMGetAllTasksStatusesVDS failed: Not SPM: ()
This is not related. You may have other issue in this setup.
On my browser it indicates that there is no tracking, verified by my domain, You have
granted this website additional permission.
Do you have secure connection or not?
Upload will not work if you don't have a secure connection.
6:41 p.m.
I started to investigate based on your question regarding a secure connection. From that
investigation this what I’ve found:
When viewing he certificate the AIA section shows the following:
Authority Info (AIA)
Location:
http://ovirtdl380gen10.cscd.net:80/ovirt-engine/services/pki-resource?res...
Method: CA Issuers
It appears that the certificate is being issue/released on port 80, could this be the
reason no connection can be established with the “ovirt imageio” service; since the
service is looking for a connection on a secured port such as 443?
How can or what should be done to correct this. If this is the issue I suspect that I
need to have a certificate that is from port 443 or some other secured connection.
Thanks
7:01 p.m.
No. The AIA section is for certificate distribution only. It's used if
the client cannot build a valid certificate chain with it's current
information. In that case it needs an insecure connection, or a secure
connection that the client can build a certificate chain for, to be
able to download the CA. You cannot use a certificate you don't have to
establish a secure connection for downloading that same certificate.
-Patrick Hibbs
On Wed, 2022-05-11 at 15:41 +0000, louisb(a)ameritech.net wrote:
I started to investigate based on your question regarding a secure
connection. From that investigation this what I’ve found:
When viewing he certificate the AIA section shows the following:
Authority Info (AIA)
Location:
http://ovirtdl380gen10.cscd.net:80/ovirt-engine/services/pki-resource?res...
Method: CA Issuers
It appears that the certificate is being issue/released on port 80,
could this be the reason no connection can be established with the
“ovirt imageio” service; since the service is looking for a
connection on a secured port such as 443?
How can or what should be done to correct this. If this is the issue
I suspect that I need to have a certificate that is from port 443 or
some other secured connection.
Thanks
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/2C3FIPZEZ4H...
7:02 p.m.
On Wed, May 11, 2022 at 6:42 PM <louisb(a)ameritech.net> wrote:
I started to investigate based on your question regarding a secure connection. From that
investigation this what I’ve found:
When viewing he certificate the AIA section shows the following:
Authority Info (AIA)
Location:
http://ovirtdl380gen10.cscd.net:80/ovirt-engine/services/pki-resource?res...
Method: CA Issuers
It appears that the certificate is being issue/released on port 80, could this be the
reason no connection can be established with the “ovirt imageio” service; since the
service is looking for a connection on a secured port such as 443?
How can or what should be done to correct this. If this is the issue I suspect that I
need to have a certificate that is from port 443 or some other secured connection.
So you are accessing the engine via http:?
I don't think this can work for image upload. We support only https.
Access engine at:
https://ovirtdl380gen10.cscd.net/
You should get a secure connection - if not download the certificate
and install it,
and make sure the proxy is disabled, and upload should work.
Trying your engine address:
https://ovirtdl380gen10.cscd.net/
I get unrelated site (24th Judicial District Community ...). You may
need to fix the web server
setup so engine can be accessed using https.
Also having engine accessible on the web is not a good idea, it is
better to make it available
only inside a closed network.
Nir
9:57 p.m.
I checked the network configuration on both the Client & Server I found network proxy
turned off. However, during the installation of ovirt there is a question regarding
proxy. The question is as follows:
Configure WebSocket Proxy on this machine? (Yes, No) [Yes]:
I took the default above could this my issue?
Thanks
11:53 p.m.
On Wed, May 11, 2022 at 9:58 PM <louisb(a)ameritech.net> wrote:
I checked the network configuration on both the Client & Server I found network proxy
turned off. However, during the installation of ovirt there is a question regarding
proxy. The question is as follows:
Configure WebSocket Proxy on this machine? (Yes, No) [Yes]:
I took the default above could this my issue?
No, the web socket proxy is not related.
12:44 a.m.
The ovirt server is internal only, could it be my browser configuration? I keep look but
I’m not seeing anything. I’ve deleted the certificate and reloaded it several time with
change.
I’ve tried connection on server and on a workstation nothing appears to be working, I’m
getting the same results.
What else or where else should I look.
I appreciate all of your help.
9:13 a.m.
On Wed, May 11, 2022 at 6:42 PM <louisb(a)ameritech.net> wrote:
I started to investigate based on your question regarding a secure connection. From that
investigation this what I’ve found:
When viewing he certificate the AIA section shows the following:
Authority Info (AIA)
Location:
http://ovirtdl380gen10.cscd.net:80/ovirt-engine/services/pki-resource?res...
Which certificate? I suppose you mean the https certificate. The CA
certificate should not have AIA.
Are you sure you imported the CA cert to your browser correctly?
Method: CA Issuers
It appears that the certificate is being issue/released on port 80, could this be the
reason no connection can be established with the “ovirt imageio” service; since the
service is looking for a connection on a secured port such as 443?
It's _available_ via both 80 and 443, bug advertised on 80 -
otherwise, you run into a chicken-and-egg problem: You want to
securely get the CA cert, but to do that, you need the CA cert...
But that's unrelated to your issue, IMO.
How can or what should be done to correct this. If this is the issue I suspect that I
need to have a certificate that is from port 443 or some other secured connection.
Again:
Please ignore AIA.
You should _manually_ get the CA cert and import it into your browser,
as Nir detailed.
If you are unsure whether you got the correct cert, you can also copy
it from the engine machine with ssh, from /etc/pki/ovirt-engine/ca.pem
.
Good luck and best regards,
--
Didi
12:52 a.m.
I’ve tried your suggestion and continue to get the same results.
Based on continuing investigation I’ve found on the Red Hat Knowledge base a resolution to
this issue, the following link references the solution:
https://access.redhat.com/solutions/354255.
However, I’ve run across another issue, since the creation of a new host within ovirt I’ve
not been able to access the internet or reach the host/server remotely. Therefore, I’m
unable to try the solution provide via the Red Hat Knowledge Base.
I’ve reviewed the kernel routing table displayed below:
ip route show
default via 20.10.20.1 dev eno5 proto static metric 100
default via 20.10.20.1 dev eno6 proto static metric 101
default via 20.10.20.1 dev eno7 proto static metric 102
default via 20.10.20.1 dev ovirtmgmt proto static metric 425
20.10.20.0/24 dev eno5 proto kernel scope link src 20.10.20.65 metric 100
20.10.20.0/24 dev eno6 proto kernel scope link src 20.10.20.66 metric 101
20.10.20.0/24 dev eno7 proto kernel scope link src 20.10.20.67 metric 102
20.10.20.0/24 dev ovirtmgmt proto kernel scope link src 20.10.20.68 metric 425
Is it normal behavior for the host to sever all connection when a “Host” machine is added
to ovirt? Is there a solution to this issue? I’ve recognize the risks of having the
host exposed to the internet, how would I keep the OS/RHEL 8.6 & ovirt current?
Thanks
3:13 p.m.
On Sat, May 14, 2022 at 12:53 AM <louisb(a)ameritech.net> wrote:
I’ve tried your suggestion and continue to get the same results.
It will be more helpful if you describe in detail what you tried
and what the results were.
Based on continuing investigation I’ve found on the Red Hat Knowledge
base a resolution to this issue, the following link references the solution:
https://access.redhat.com/solutions/354255.
This URL does not exist.
However, I’ve run across another issue, since the creation of a new
host within ovirt
Based on the output of "ovirt-imageio --show-config" you had an all-in-one
setup, when the engine host is added to the engine as a hypervisor. This setup
is not supported but works, but adding more hosts to this kind of setup will not
work with image transfer, and it is a really bad idea to have multiple hosts and
run engine on one of them.
For example, engine can stop a host using host power management API. If this
is the host running engine you don't have a way to start your engine unless you
have access to the host power management console.
If have more than one host, your engine should not run on any of the hosts,
and you must enable the imageio proxy (this is the default):
engine-config -s ImageTransferProxyEnabled=true
And restart engine:
systemctl restart ovirt-engine
I’ve not been able to access the internet or reach the host/server
remotely. Therefore, I’m unable to try the solution provide via the Red Hat Knowledge
Base.
I’ve reviewed the kernel routing table displayed below:
ip route show
default via 20.10.20.1 dev eno5 proto static metric 100
default via 20.10.20.1 dev eno6 proto static metric 101
default via 20.10.20.1 dev eno7 proto static metric 102
default via 20.10.20.1 dev ovirtmgmt proto static metric 425
20.10.20.0/24 dev eno5 proto kernel scope link src 20.10.20.65 metric 100
20.10.20.0/24 dev eno6 proto kernel scope link src 20.10.20.66 metric 101
20.10.20.0/24 dev eno7 proto kernel scope link src 20.10.20.67 metric 102
20.10.20.0/24 dev ovirtmgmt proto kernel scope link src 20.10.20.68 metric 425
Is it normal behavior for the host to sever all connection when a “Host” machine is added
to ovirt? Is there a solution to this issue? I’ve recognize the risks of having the
host exposed to the internet, how would I keep the OS/RHEL 8.6 & ovirt current?
It is hard to tell what's going on when we don't know which
hosts do you have and what is their ip address.
Please confirm that you access engine using https:// and that
when you access the host your browser reports a secure connection
without warnings (meaning that engine CA certificate was added to
the browser).
Nir
6:33 p.m.
You shouldn't need to change anything if you are using the apache cert
generated by engine-setup. That whole conversation only applies if
you've changed the certificate used by apache on the engine host.
For default setups, you just need to import and trust the CA generated
by engine-setup into your browser(s).
-Patrick Hibbs
On Mon, 2022-05-09 at 19:38 +0000, louisb(a)ameritech.net wrote:
I’m trying to upload an ISO image in ovirt 4.4.10, It’s been a huge
challenge to accomplish this. I read several post regarding this
issue, I really don’t have s clear understanding of solution to this
issue. My experience has not been very fruitful at all.
When I try to perform the upload using the web GUI I get the
following message in the status column: “Paused by System“. I’ve
been reading for roughly three weeks trying to understand and resolve
the issue. There is a tremendous amount of discussion centered
around changing certificate file located in the directory
“etcpki/ovirt-engine”, however it not clear at all what files need to
change.
My installation is an out-of-box installation with any certificates
beginning generated as part of the install process, I’ve imported the
certificate that was generated into my browser/Firefox 91.9.0.
Based on what I’ve been reading the solution to my problems is that
the certificate does not match the certificate defined in the
“imageio-service”, my question is why because it was generated as
part of the installation?
What files in the “/etc/pki/ovirt-engine” must be changed to get
things working. Further should or do I copy the certificate saved
from the GUI to files under “/etc/pki/ovirt-engine” directory?
I feel like I’m so close after six month of reading and re-installs,
what do I do next?
Thanks
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/YVGGVNOQ5FL...
8:39 p.m.
Thank you very much for your response and I agree with you based on everything I've
read. But below are the steps that I've followed:
I greatly appreciate the response, however, following you instructions I’m still not able
to upload an ISO via the GUI.
When try an upload using the GUI I follow the instruction below:
• In the pane on the left hand side of the screen, I select “Storage”.
• Select “Disks”.
• Where I get the screen “Storage > Disks”.
• On the top right hand side of the screen, I select “Upload”.
• From the pull down menu I select “Start”.
• I choose the file/ISO I want to upload, in this case its “CENTOS-Stream” version 9.
• At the bottom of the screen I click the “Test Connection” button.
• The following messages appears:
Connection to “ovirt-imageio-service” has failed. Ensure the “ovirt certificate” is
registered as a valid CA in the browser.
• I click/select the “ovirt certificate” which is highlighted in blue on my screen.
• It displays the option to save the certificate or view it in the browser. My
browser is Firefox 91.9.0.
• I save the certificate which I later import into my browser (following your
instruction). The certificate is accepted by the browser with no errors encountered.
• I then restart the upload process again and “Test Connection”. The same message is
displayed:
Connection to “ovirt-imageio-service” has failed. Ensure the “ovirt certificate” is
registered as a valid CA in the browser. The same message as earlier in the process.
Is there some place other place I should be looking for more information or something else
I should be doing?
922
days inactive
928
days old
20 comments
4 participants
participants (4)
-
louisb＠ameritech.net -
Nir Soffer -
Patrick Hibbs -
Yedidyah Bar David