7:11 p.m.
On 01/18/2014 04:52 PM, Peter Styk wrote:
So I got ovirtmgmt VM ticked off. Had to remove it from all VM's
then
tried to add new Logical network to eth0 by drag & drop but refused
since ovirtmgmt was out of sync. So I synced it. ....and that's how I
lost access to my hosted remote system. End of story. So that's it I
guess, automated install doesn't work (during switch network goes dead
and doesn't come back remote access is lost) so I found manual way that
works. But then I need to sync it to get my ovirtmgmt not to be a VM
network. And even if its not to get another network on the interface i
need to sync it.....
this sounds like a bug - can you provide clear reproduction steps?
I will keep trying, Thanks for the tips.
P.
On 17 January 2014 22:06, Itamar Heim <iheim(a)redhat.com
<mailto:iheim@redhat.com>> wrote:
On 01/18/2014 12:05 AM, William Kwan wrote:
I tried to define a virtual interface for vlan102, by
adding ifcfg-bond0.102
manually and restarted network services.
why not via ovirt-engine?
On Friday, January 17, 2014 4:45 PM, Itamar Heim
<iheim(a)redhat.com <mailto:iheim@redhat.com>> wrote:
On 01/17/2014 11:38 PM, William Kwan wrote:
> OK.. tested with bond0.102 for vlan102
> I guess I can't do this with oVirt? It wouldn't pickup this
interface.
> It still shows up eth0, eth1 and bond0 only
you tried to define a vlan youself on the bond, or use a vlan via a
logical network over the bond via ovirt-engine (which should work)?
>
> Will
>
>
>
> On Friday, January 17, 2014 1:15 PM, William Kwan
<potatok(a)yahoo.com <mailto:potatok@yahoo.com>
<mailto:potatok@yahoo.com <mailto:potatok@yahoo.com>>> wrote:
> Thanks all for the info. I'm trying the suggestions with
3.3.2-1.el6
>
> Assaf mentioned the following which is true.
> You can make ovirtmgmt a non-VM, untagged (non-VLAN)
network, then place
> as many VM, tagged networks as you'd like on the same NIC or
bond.
>
> I tried a few things and I haven't been able to find a way
through.
> Obviously or not, there are more facts/rules. Just put up a
few of them
> here
>
> Cannot have more than one non-VLAN network on one interface
> Cannot have a non-VLAN VM network and VLAN-tagged networks
on one
> interface. ( got this when I tried to drag a VLAN-tagged VM
network on
> the same interface as the non-VLAN VM network).
>
> I'll try to test adding a bond0.<vlan>. I need to have
> bond0 - for both mgmt network and a vlan
> bond1 - for another subnet.
>
> Will
>
>
>
>
> On Thursday, January 16, 2014 1:50 PM, Juan Pablo Lorier
> <jplorier(a)gmail.com <mailto:jplorier@gmail.com>
<mailto:jplorier@gmail.com <mailto:jplorier@gmail.com>>> wrote:
> Hi William,
>
> You can have several logical networks on the same interface. If
> ovirtmgmt is not a vm network you can even mix tagged and
untagged
> networks (if not, you can't mix). You don's have to do
anything besides
> creating the logical networks in ovirt and assign them to
the interface,
> ovirt takes care of creating the virtual interfaces it needs.
> What you can't do is have more than one logical network per
vlan (I
> think there's a feature request on this, I know I've asked
it on the
>
> list:-) ).
> Regards,
>
>
>
>
>
>
>
> _________________________________________________
> Users mailing list
> Users(a)ovirt.org <mailto:Users@ovirt.org>
<mailto:Users@ovirt.org <mailto:Users@ovirt.org>>
> http://lists.ovirt.org/__mailman/listinfo/users
<http://lists.ovirt.org/mailman/listinfo/users>
>
_________________________________________________
Users mailing list
Users(a)ovirt.org <mailto:Users@ovirt.org>
http://lists.ovirt.org/__mailman/listinfo/users
<http://lists.ovirt.org/mailman/listinfo/users>