6:45 p.m.
On Fri, Aug 23, 2019 at 5:41 PM Curtis E. Combs Jr. <ej.albany(a)gmail.com>
wrote:
Also, if it helps, the hosts will sit there, quietly, for hours or
days before anything happens. They're up and working just fine. But
then, when I manually migrate a VM from one host to another, they
become completely inaccessible.
Can you share some details about your storage?
Maybe there is a feature used during live migration, which triggers the
issue.
These are vanilla-as-possible CentOS7 nodes. Very basic ovirt
install
and configuration.
On Fri, Aug 23, 2019 at 11:33 AM Curtis E. Combs Jr.
<ej.albany(a)gmail.com> wrote:
>
> Hey Dominik,
>
> Thanks for helping. I really want to try to use ovirt.
>
> When these events happen, I cannot even SSH to the nodes due to the
> link being down. After a little while, the hosts come back...
>
> On Fri, Aug 23, 2019 at 11:30 AM Dominik Holler <dholler(a)redhat.com>
wrote:
> >
> > Is you storage connected via NFS?
> > Can you manually access the storage on the host?
> >
> >
> > On Fri, Aug 23, 2019 at 5:19 PM Curtis E. Combs Jr. <
ej.albany(a)gmail.com> wrote:
> >>
> >> Sorry to dead bump this, but I'm beginning to suspect that maybe
it's
> >> not STP that's the problem.
> >>
> >> 2 of my hosts just went down when a few VMs tried to migrate.
> >>
> >> Do any of you have any idea what might be going on here? I don't even
> >> know where to start. I'm going to include the dmesg in case it helps.
> >> This happens on both of the hosts whenever any migration attempts to
start.
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >> [68099.245833] bnx2 0000:01:00.0 em1: NIC Copper Link is Down
> >> [68099.246055] internal: port 1(em1) entered disabled state
> >> [68184.177343] ixgbe 0000:03:00.0 p1p1: NIC Link is Down
> >> [68184.177789] ovirtmgmt: port 1(p1p1) entered disabled state
> >> [68184.177856] ovirtmgmt: topology change detected, propagating
> >> [68277.078671] INFO: task qemu-kvm:8888 blocked for more than 120
seconds.
> >> [68277.078700] "echo 0 >
/proc/sys/kernel/hung_task_timeout_secs"
> >> disables this message.
> >> [68277.078723] qemu-kvm D ffff9db40c359040 0 8888 1
0x000001a0
> >> [68277.078727] Call Trace:
> >> [68277.078738] [<ffffffff978fd2ac>] ? avc_has_perm_flags+0xdc/0x1c0
> >> [68277.078743] [<ffffffff97d69f19>] schedule+0x29/0x70
> >> [68277.078746] [<ffffffff9785f3d9>] inode_dio_wait+0xd9/0x100
> >> [68277.078751] [<ffffffff976c4010>] ? wake_bit_function+0x40/0x40
> >> [68277.078765] [<ffffffffc09d6dd6>] nfs_getattr+0x1b6/0x250 [nfs]
> >> [68277.078768] [<ffffffff97848109>] vfs_getattr+0x49/0x80
> >> [68277.078769] [<ffffffff97848185>] vfs_fstat+0x45/0x80
> >> [68277.078771] [<ffffffff978486f4>] SYSC_newfstat+0x24/0x60
> >> [68277.078774] [<ffffffff97d76d21>] ?
system_call_after_swapgs+0xae/0x146
> >> [68277.078778] [<ffffffff97739f34>] ?
__audit_syscall_entry+0xb4/0x110
> >> [68277.078782] [<ffffffff9763aaeb>] ?
syscall_trace_enter+0x16b/0x220
> >> [68277.078784] [<ffffffff97848ace>] SyS_newfstat+0xe/0x10
> >> [68277.078786] [<ffffffff97d7706b>] tracesys+0xa3/0xc9
> >> [68397.072384] INFO: task qemu-kvm:8888 blocked for more than 120
seconds.
> >> [68397.072413] "echo 0 >
/proc/sys/kernel/hung_task_timeout_secs"
> >> disables this message.
> >> [68397.072436] qemu-kvm D ffff9db40c359040 0 8888 1
0x000001a0
> >> [68397.072439] Call Trace:
> >> [68397.072453] [<ffffffff978fd2ac>] ? avc_has_perm_flags+0xdc/0x1c0
> >> [68397.072458] [<ffffffff97d69f19>] schedule+0x29/0x70
> >> [68397.072462] [<ffffffff9785f3d9>] inode_dio_wait+0xd9/0x100
> >> [68397.072467] [<ffffffff976c4010>] ? wake_bit_function+0x40/0x40
> >> [68397.072480] [<ffffffffc09d6dd6>] nfs_getattr+0x1b6/0x250 [nfs]
> >> [68397.072485] [<ffffffff97848109>] vfs_getattr+0x49/0x80
> >> [68397.072486] [<ffffffff97848185>] vfs_fstat+0x45/0x80
> >> [68397.072488] [<ffffffff978486f4>] SYSC_newfstat+0x24/0x60
> >> [68397.072491] [<ffffffff97d76d21>] ?
system_call_after_swapgs+0xae/0x146
> >> [68397.072495] [<ffffffff97739f34>] ?
__audit_syscall_entry+0xb4/0x110
> >> [68397.072498] [<ffffffff9763aaeb>] ?
syscall_trace_enter+0x16b/0x220
> >> [68397.072500] [<ffffffff97848ace>] SyS_newfstat+0xe/0x10
> >> [68397.072502] [<ffffffff97d7706b>] tracesys+0xa3/0xc9
> >> [68401.573141] bnx2 0000:01:00.0 em1: NIC Copper Link is Up, 1000 Mbps
> >> full duplex
> >>
> >> [68401.573247] internal: port 1(em1) entered blocking state
> >> [68401.573255] internal: port 1(em1) entered listening state
> >> [68403.576985] internal: port 1(em1) entered learning state
> >> [68405.580907] internal: port 1(em1) entered forwarding state
> >> [68405.580916] internal: topology change detected, propagating
> >> [68469.565589] nfs: server swm-01.hpc.moffitt.org not responding,
timed out
> >> [68469.565840] nfs: server swm-01.hpc.moffitt.org not responding,
timed out
> >> [68487.193932] ixgbe 0000:03:00.0 p1p1: NIC Link is Up 10 Gbps, Flow
> >> Control: RX/TX
> >> [68487.194105] ovirtmgmt: port 1(p1p1) entered blocking state
> >> [68487.194114] ovirtmgmt: port 1(p1p1) entered listening state
> >> [68489.196508] ovirtmgmt: port 1(p1p1) entered learning state
> >> [68491.200400] ovirtmgmt: port 1(p1p1) entered forwarding state
> >> [68491.200405] ovirtmgmt: topology change detected, sending tcn bpdu
> >> [68493.672423] NFS: nfs4_reclaim_open_state: Lock reclaim failed!
> >> [68494.777996] NFSD: client 10.15.28.22 testing state ID with
> >> incorrect client ID
> >> [68494.778580] NFSD: client 10.15.28.22 testing state ID with
> >> incorrect client ID
> >>
> >>
> >> On Thu, Aug 22, 2019 at 2:53 PM Curtis E. Combs Jr. <
ej.albany(a)gmail.com> wrote:
> >> >
> >> > Thanks, I'm just going to revert back to bridges.
> >> >
> >> > On Thu, Aug 22, 2019 at 11:50 AM Dominik Holler
<dholler(a)redhat.com>
wrote:
> >> > >
> >> > >
> >> > >
> >> > > On Thu, Aug 22, 2019 at 3:06 PM Curtis E. Combs Jr. <
ej.albany(a)gmail.com> wrote:
> >> > >>
> >> > >> Seems like the STP options are so common and necessary that
it
would
> >> > >> be a priority over seldom-used bridge_opts. I know what STP
is
and I'm
> >> > >> not even a networking guy - never even heard of half of the
> >> > >> bridge_opts that have switches in the UI.
> >> > >>
> >> > >> Anyway. I wanted to try the openvswitches, so I reinstalled
all
of my
> >> > >> nodes and used "openvswitch (Technology Preview)"
as the
engine-setup
> >> > >> option for the first host. I made a new Cluster for my
nodes,
added
> >> > >> them all to the new cluster, created a new "logical
network" for
the
> >> > >> internal network and attached it to the internal network
ports.
> >> > >>
> >> > >> Now, when I go to create a new VM, I don't even have
either the
> >> > >> ovirtmgmt switch OR the internal switch as an option. The
drop-down is
> >> > >> empy as if I don't have any vnic-profiles.
> >> > >>
> >> > >
> >> > > openvswitch clusters are limited to ovn networks.
> >> > > You can create one like described in
> >> > >
https://www.ovirt.org/documentation/admin-guide/chap-External_Providers.h...
> >> > >
> >> > >
> >> > >>
> >> > >> On Thu, Aug 22, 2019 at 7:34 AM Tony Pearce
<tonyppe(a)gmail.com>
wrote:
> >> > >> >
> >> > >> > Hi Dominik, would you mind sharing the use case for stp
via
API Only? I am keen to know this.
> >> > >> > Thanks
> >> > >> >
> >> > >> >
> >> > >> > On Thu., 22 Aug. 2019, 19:24 Dominik Holler, <
dholler(a)redhat.com> wrote:
> >> > >> >>
> >> > >> >>
> >> > >> >>
> >> > >> >> On Thu, Aug 22, 2019 at 1:08 PM Miguel Duarte de
Mora Barroso
<mdbarroso(a)redhat.com> wrote:
> >> > >> >>>
> >> > >> >>> On Sat, Aug 17, 2019 at 11:27 AM
<ej.albany(a)gmail.com>
wrote:
> >> > >> >>> >
> >> > >> >>> > Hello. I have been trying to figure out an
issue for a
very long time.
> >> > >> >>> > That issue relates to the ethernet and 10gb
fc links that
I have on my
> >> > >> >>> > cluster being disabled any time a migration
occurs.
> >> > >> >>> >
> >> > >> >>> > I believe this is because I need to have
STP turned on in
order to
> >> > >> >>> > participate with the switch. However, there
does not seem
to be any
> >> > >> >>> > way to tell oVirt to stop turning it off!
Very frustrating.
> >> > >> >>> >
> >> > >> >>> > After entering a cronjob that enables stp
on all bridges
every 1
> >> > >> >>> > minute, the migration issue disappears....
> >> > >> >>> >
> >> > >> >>> > Is there any way at all to do without this
cronjob and set
STP to be
> >> > >> >>> > ON without having to resort to such a silly
solution?
> >> > >> >>>
> >> > >> >>> Vdsm exposes a per bridge STP knob that you can
use for
this. By
> >> > >> >>> default it is set to false, which is probably
why you had to
use this
> >> > >> >>> shenanigan.
> >> > >> >>>
> >> > >> >>> You can, for instance:
> >> > >> >>>
> >> > >> >>> # show present state
> >> > >> >>> [vagrant@vdsm ~]$ ip a
> >> > >> >>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536
qdisc noqueue state
UNKNOWN
> >> > >> >>> group default qlen 1000
> >> > >> >>> link/loopback 00:00:00:00:00:00 brd
00:00:00:00:00:00
> >> > >> >>> inet 127.0.0.1/8 scope host lo
> >> > >> >>> valid_lft forever preferred_lft forever
> >> > >> >>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP>
mtu 1500 qdisc
pfifo_fast
> >> > >> >>> state UP group default qlen 1000
> >> > >> >>> link/ether 52:54:00:41:fb:37 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP>
mtu 1500 qdisc
pfifo_fast
> >> > >> >>> state UP group default qlen 1000
> >> > >> >>> link/ether 52:54:00:83:5b:6f brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> inet 192.168.50.50/24 brd 192.168.50.255
scope global
noprefixroute eth1
> >> > >> >>> valid_lft forever preferred_lft forever
> >> > >> >>> inet6 fe80::5054:ff:fe83:5b6f/64 scope link
> >> > >> >>> valid_lft forever preferred_lft forever
> >> > >> >>> 19: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu
1500 qdisc noop
state DOWN
> >> > >> >>> group default qlen 1000
> >> > >> >>> link/ether 8e:5c:2e:87:fa:0b brd
ff:ff:ff:ff:ff:ff
> >> > >> >>>
> >> > >> >>> # show example bridge configuration - you're
looking for the
STP knob here.
> >> > >> >>> [root@vdsm ~]$ cat bridged_net_with_stp
> >> > >> >>> {
> >> > >> >>> "bondings": {},
> >> > >> >>> "networks": {
> >> > >> >>> "test-network": {
> >> > >> >>> "nic": "eth0",
> >> > >> >>> "switch": "legacy",
> >> > >> >>> "bridged": true,
> >> > >> >>> "stp": true
> >> > >> >>> }
> >> > >> >>> },
> >> > >> >>> "options": {
> >> > >> >>> "connectivityCheck": false
> >> > >> >>> }
> >> > >> >>> }
> >> > >> >>>
> >> > >> >>> # issue setup networks command:
> >> > >> >>> [root@vdsm ~]$ vdsm-client -f
bridged_net_with_stp Host
setupNetworks
> >> > >> >>> {
> >> > >> >>> "code": 0,
> >> > >> >>> "message": "Done"
> >> > >> >>> }
> >> > >> >>>
> >> > >> >>> # show bridges
> >> > >> >>> [root@vdsm ~]$ brctl show
> >> > >> >>> bridge name bridge id STP enabled interfaces
> >> > >> >>> ;vdsmdummy; 8000.000000000000 no
> >> > >> >>> test-network 8000.52540041fb37 yes eth0
> >> > >> >>>
> >> > >> >>> # show final state
> >> > >> >>> [root@vdsm ~]$ ip a
> >> > >> >>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536
qdisc noqueue state
UNKNOWN
> >> > >> >>> group default qlen 1000
> >> > >> >>> link/loopback 00:00:00:00:00:00 brd
00:00:00:00:00:00
> >> > >> >>> inet 127.0.0.1/8 scope host lo
> >> > >> >>> valid_lft forever preferred_lft forever
> >> > >> >>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP>
mtu 1500 qdisc
pfifo_fast
> >> > >> >>> master test-network state UP group default qlen
1000
> >> > >> >>> link/ether 52:54:00:41:fb:37 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP>
mtu 1500 qdisc
pfifo_fast
> >> > >> >>> state UP group default qlen 1000
> >> > >> >>> link/ether 52:54:00:83:5b:6f brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> inet 192.168.50.50/24 brd 192.168.50.255
scope global
noprefixroute eth1
> >> > >> >>> valid_lft forever preferred_lft forever
> >> > >> >>> inet6 fe80::5054:ff:fe83:5b6f/64 scope link
> >> > >> >>> valid_lft forever preferred_lft forever
> >> > >> >>> 19: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu
1500 qdisc noop
state DOWN
> >> > >> >>> group default qlen 1000
> >> > >> >>> link/ether 8e:5c:2e:87:fa:0b brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> 432: test-network:
<BROADCAST,MULTICAST,UP,LOWER_UP> mtu
1500 qdisc
> >> > >> >>> noqueue state UP group default qlen 1000
> >> > >> >>> link/ether 52:54:00:41:fb:37 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>>
> >> > >> >>> I don't think this STP parameter is exposed
via engine UI;
@Dominik
> >> > >> >>> Holler , could you confirm ? What are our plans
for it ?
> >> > >> >>>
> >> > >> >>
> >> > >> >> STP is only available via REST-API, see
> >> > >> >>
http://ovirt.github.io/ovirt-engine-api-model/4.3/#types/network
> >> > >> >> please find an example how to enable STP in
> >> > >> >>
https://gist.github.com/dominikholler/4e70c9ef9929d93b6807f56d43a70b95
> >> > >> >>
> >> > >> >> We have no plans to add STP to the web ui,
> >> > >> >> but new feature requests are always welcome on
> >> > >> >>
https://bugzilla.redhat.com/enter_bug.cgi?product=ovirt-engine
> >> > >> >>
> >> > >> >>
> >> > >> >>>
> >> > >> >>> >
> >> > >> >>> > Here are some details about my systems, if
you need it.
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> > selinux is disabled.
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> >
> >> > >> >>> > [root@swm-02 ~]# rpm -qa | grep ovirt
> >> > >> >>> > ovirt-imageio-common-1.5.1-0.el7.x86_64
> >> > >> >>> > ovirt-release43-4.3.5.2-1.el7.noarch
> >> > >> >>> > ovirt-imageio-daemon-1.5.1-0.el7.noarch
> >> > >> >>> > ovirt-vmconsole-host-1.0.7-2.el7.noarch
> >> > >> >>> >
ovirt-hosted-engine-setup-2.3.11-1.el7.noarch
> >> > >> >>> >
ovirt-ansible-hosted-engine-setup-1.0.26-1.el7.noarch
> >> > >> >>> >
python2-ovirt-host-deploy-1.8.0-1.el7.noarch
> >> > >> >>> >
ovirt-ansible-engine-setup-1.1.9-1.el7.noarch
> >> > >> >>> > python2-ovirt-setup-lib-1.2.0-1.el7.noarch
> >> > >> >>> > cockpit-machines-ovirt-195.1-1.el7.noarch
> >> > >> >>> > ovirt-hosted-engine-ha-2.3.3-1.el7.noarch
> >> > >> >>> > ovirt-vmconsole-1.0.7-2.el7.noarch
> >> > >> >>> >
cockpit-ovirt-dashboard-0.13.5-1.el7.noarch
> >> > >> >>> >
ovirt-provider-ovn-driver-1.2.22-1.el7.noarch
> >> > >> >>> >
ovirt-host-deploy-common-1.8.0-1.el7.noarch
> >> > >> >>> > ovirt-host-4.3.4-1.el7.x86_64
> >> > >> >>> >
python-ovirt-engine-sdk4-4.3.2-2.el7.x86_64
> >> > >> >>> > ovirt-host-dependencies-4.3.4-1.el7.x86_64
> >> > >> >>> >
ovirt-ansible-repositories-1.1.5-1.el7.noarch
> >> > >> >>> > [root@swm-02 ~]# cat /etc/redhat-release
> >> > >> >>> > CentOS Linux release 7.6.1810 (Core)
> >> > >> >>> > [root@swm-02 ~]# uname -r
> >> > >> >>> > 3.10.0-957.27.2.el7.x86_64
> >> > >> >>> > You have new mail in /var/spool/mail/root
> >> > >> >>> > [root@swm-02 ~]# ip a
> >> > >> >>> > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu
65536 qdisc noqueue
state UNKNOWN
> >> > >> >>> > group default qlen 1000
> >> > >> >>> > link/loopback 00:00:00:00:00:00 brd
00:00:00:00:00:00
> >> > >> >>> > inet 127.0.0.1/8 scope host lo
> >> > >> >>> > valid_lft forever preferred_lft
forever
> >> > >> >>> > 2: em1:
<BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
mq master
> >> > >> >>> > test state UP group default qlen 1000
> >> > >> >>> > link/ether d4:ae:52:8d:50:48 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > 3: em2: <BROADCAST,MULTICAST> mtu
1500 qdisc noop state
DOWN group
> >> > >> >>> > default qlen 1000
> >> > >> >>> > link/ether d4:ae:52:8d:50:49 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > 4: p1p1:
<BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
mq master
> >> > >> >>> > ovirtmgmt state UP group default qlen 1000
> >> > >> >>> > link/ether 90:e2:ba:1e:14:80 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > 5: p1p2: <BROADCAST,MULTICAST> mtu
1500 qdisc noop state
DOWN group
> >> > >> >>> > default qlen 1000
> >> > >> >>> > link/ether 90:e2:ba:1e:14:81 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > 6: ovs-system: <BROADCAST,MULTICAST>
mtu 1500 qdisc noop
state DOWN
> >> > >> >>> > group default qlen 1000
> >> > >> >>> > link/ether a2:b8:d6:e8:b3:d8 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > 7: br-int: <BROADCAST,MULTICAST> mtu
1500 qdisc noop state
DOWN group
> >> > >> >>> > default qlen 1000
> >> > >> >>> > link/ether 96:a0:c1:4a:45:4b brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > 25: test:
<BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
noqueue
> >> > >> >>> > state UP group default qlen 1000
> >> > >> >>> > link/ether d4:ae:52:8d:50:48 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > inet 10.15.11.21/24 brd 10.15.11.255
scope global test
> >> > >> >>> > valid_lft forever preferred_lft
forever
> >> > >> >>> > 26: ovirtmgmt:
<BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc
> >> > >> >>> > noqueue state UP group default qlen 1000
> >> > >> >>> > link/ether 90:e2:ba:1e:14:80 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > inet 10.15.28.31/24 brd 10.15.28.255
scope global
ovirtmgmt
> >> > >> >>> > valid_lft forever preferred_lft
forever
> >> > >> >>> > 27: ;vdsmdummy;:
<BROADCAST,MULTICAST> mtu 1500 qdisc noop
state DOWN
> >> > >> >>> > group default qlen 1000
> >> > >> >>> > link/ether 62:e5:e5:07:99:eb brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > 29: vnet0:
<BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc mq master
> >> > >> >>> > ovirtmgmt state UNKNOWN group default qlen
1000
> >> > >> >>> > link/ether fe:6f:9c:95:00:02 brd
ff:ff:ff:ff:ff:ff
> >> > >> >>> > [root@swm-02 ~]# free -m
> >> > >> >>> > total used free
shared
buff/cache available
> >> > >> >>> > Mem: 64413 1873 61804
9
735 62062
> >> > >> >>> > Swap: 16383 0
16383
> >> > >> >>> > [root@swm-02 ~]# free -h
> >> > >> >>> > total used free
shared
buff/cache available
> >> > >> >>> > Mem: 62G 1.8G 60G
9.5M
735M 60G
> >> > >> >>> > Swap: 15G 0B
15G
> >> > >> >>> > [root@swm-02 ~]# ls
> >> > >> >>> > ls lsb_release
lshw
lslocks
> >> > >> >>> > lsmod lspci
lssubsys
> >> > >> >>> > lsusb.py
> >> > >> >>> > lsattr lscgroup
lsinitrd
lslogins
> >> > >> >>> > lsns lss16toppm
lstopo-no-graphics
> >> > >> >>> > lsblk lscpu
lsipc
lsmem
> >> > >> >>> > lsof lsscsi
lsusb
> >> > >> >>> > [root@swm-02 ~]# lscpu
> >> > >> >>> > Architecture: x86_64
> >> > >> >>> > CPU op-mode(s): 32-bit, 64-bit
> >> > >> >>> > Byte Order: Little Endian
> >> > >> >>> > CPU(s): 16
> >> > >> >>> > On-line CPU(s) list: 0-15
> >> > >> >>> > Thread(s) per core: 2
> >> > >> >>> > Core(s) per socket: 4
> >> > >> >>> > Socket(s): 2
> >> > >> >>> > NUMA node(s): 2
> >> > >> >>> > Vendor ID: GenuineIntel
> >> > >> >>> > CPU family: 6
> >> > >> >>> > Model: 44
> >> > >> >>> > Model name: Intel(R) Xeon(R)
CPU
X5672 @ 3.20GHz
> >> > >> >>> > Stepping: 2
> >> > >> >>> > CPU MHz: 3192.064
> >> > >> >>> > BogoMIPS: 6384.12
> >> > >> >>> > Virtualization: VT-x
> >> > >> >>> > L1d cache: 32K
> >> > >> >>> > L1i cache: 32K
> >> > >> >>> > L2 cache: 256K
> >> > >> >>> > L3 cache: 12288K
> >> > >> >>> > NUMA node0 CPU(s): 0,2,4,6,8,10,12,14
> >> > >> >>> > NUMA node1 CPU(s): 1,3,5,7,9,11,13,15
> >> > >> >>> > Flags: fpu vme de pse tsc
msr pae mce cx8
apic sep
> >> > >> >>> > mtrr pge mca cmov pat pse36 clflush dts
acpi mmx fxsr sse
sse2 ss ht
> >> > >> >>> > tm pbe syscall nx pdpe1gb rdtscp lm
constant_tsc
arch_perfmon pebs bts
> >> > >> >>> > rep_good nopl xtopology nonstop_tsc
aperfmperf eagerfpu
pni pclmulqdq
> >> > >> >>> > dtes64 monitor ds_cpl vmx smx est tm2 ssse3
cx16 xtpr pdcm
pcid dca
> >> > >> >>> > sse4_1 sse4_2 popcnt aes lahf_lm ssbd ibrs
ibpb stibp
tpr_shadow vnmi
> >> > >> >>> > flexpriority ept vpid dtherm ida arat
spec_ctrl
intel_stibp flush_l1d
> >> > >> >>> > [root@swm-02 ~]#
> >> > >> >>> >
_______________________________________________
> >> > >> >>> > Users mailing list -- users(a)ovirt.org
> >> > >> >>> > To unsubscribe send an email to
users-leave(a)ovirt.org
> >> > >> >>> > Privacy Statement:
https://www.ovirt.org/site/privacy-policy/
> >> > >> >>> > oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
> >> > >> >>> > List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/MTMZ5MF4CF2...
> >> > >> >>
> >> > >> >> _______________________________________________
> >> > >> >> Users mailing list -- users(a)ovirt.org
> >> > >> >> To unsubscribe send an email to
users-leave(a)ovirt.org
> >> > >> >> Privacy Statement:
https://www.ovirt.org/site/privacy-policy/
> >> > >> >> oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
> >> > >> >> List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/QBA7NYKAJNR...