7:56 a.m.
On Fri, Feb 10, 2017 at 2:27 PM, Martin Perina <mperina(a)redhat.com> wrote:
Hi Gianluca,
so generally speaking when host is in Maintenance status, engine doesn't
communicate with this host, so you can do pretty much anything about it.
Thanks for the detailed answer, Martin.
It seemed to me that in the past I did a reboot at the host OS level while
in maintenance and this generated a series of fencing/reboots of the host
itself, so I wanted to be sure.
It is possible that at that time I also used "Confirm host has been
rebooted" button, as initially I misunderstood its target.... and it was
that action to generate fencing loops (2 or 3 I don't remember).
Then in Admin manual for 4.0 I saw that instead it is only to be used in
case of unresponsive host, correct?
"
If a host unpredictably goes into a non-responsive state, for example, due
to a hardware failure;
it can significantly affect the performance of the environment. If you do
not have a power
management device, or it is incorrectly configured, you can reboot the host
manually.
Do not use the Confirm host has been rebooted option unless you have
manually
rebooted the host. Using this option while the host is still running can
lead to a virtual
machine image corruption.
Procedure 7.20. Manually fencing or isolating a non-responsive host
1. On the Hosts tab, select the host. The status must display as
non-responsive.
2. Manually reboot the host. This could mean physically entering the lab
and rebooting the
host.
3. On the Administration Portal, right-click the host entry and select the
Confirm Host has
been rebooted button.
4. A message displays prompting you to ensure that the host has been shut
down or
rebooted. Select the Approve Operation check box and click OK.
"
Initially I misread and kept focus only to the "Manually fencing" and
"Manually reboot" but point 1. seems quite clear:
The status must display as non-responsive.
So no other use for "Confirm Host has been rebooted"
I will verify again the workflow
About the upgrade flow (host 4.0 -> 4.1), here's proper way(s) how to
achieve that:
Yes, my question was in general, eg when I'm going to pass from 4.1.0.4 to
4.1.1
1. Put host to Maintenance
2. Add 4.1 repositories to the host
3. Upgrade the host - you have 2 options here:
a. UI
- Go to Hosts tab in webadmin
- Select host and click on Reinstall inside Installation menu
b. Command line
- Connect to the host using SSH and upgrade using yum
Sometimes at this point I could have a new kernel to boot, due to the
update just completed, so the point 4. is not what I would like to do right
now.
4. Activate the host
The main difference between UI and command line options is, that with
UI
option only necessary packages like VDSM and it's dependencies are upgraded.
Now regarding restart:
1. If host is in Maintenance, restart using SSH and shutdown/reboot
execution is no problem. But if host is Up, then executing shutdown/reboot
using SSH will make host NonResponsive and fencing will be executed
2. If you select Restart using SSH from Maintenance menu, it just
connect using SSH and execute shutdown same way as it's done manually
3. If you select Restart using Power Management from Maintenance menu,
it will execute restart using PM device and further actions are hardware
dependent. On some servers it will send shutdown signal to OS similarly as
if you execute reboot and afterwards it turns off power of the server (so
the result may be the same as using shutdown from command line). But on
different hardware it can just turn off power of the server.
So for planned restart using SSH restart either from UI or from command
line is preferred way.
Ok, so a normal reboot is ok as point 4..
And then after reboot
5. Activate (and not "Confirm Host Has Rebooted"... ;-)
Regarding Power Mgmt ---> Restart
I thought that in general I should completely disable on the host the
feature to initiate shutdown in case of power button pressed, like in RHCS
or similar targeted environments:
https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/...
Is it not the case in oVirt? I think in case of fencing, it is necessary to
have the host down as soon as possible
My initial question was the confirmation about Power Mgmt --> Restart : if
it implied power Off / Power On by design or any other workflow....
Thanks in advance,
Gianluca