9:30 a.m.
Hi Yaniv,
the config on all servers were fine (with SSL).
I had to reboot the "old" hypervisors to make migration from new hypervisor
possible (restart of libvirt would crash my VMs ;) ),
was a bit hard as I hadn't any other VM slots were I could migrate to..
Just have this behavior with oVirt 3.0 environment, oVirt3.2 with minimal F18 nodes works
fine here.. strange.
Want to give you feedback here as you answered very quickly.
Thanks again!
Cheers,
Sven.
-----Ursprüngliche Nachricht-----
Von: Yaniv Bronheim [mailto:ybronhei@redhat.com]
Gesendet: Donnerstag, 2. Mai 2013 10:26
An: Sven Knohsalla
Cc: users(a)ovirt.org
Betreff: Re: [Users] oVirt 3.0 - known issue with live migration
Hi,
check your conf files, if you use secure connection to host you should check the
parameters:
in /etc/conf/vdsm/vdsm.conf - check that "ssl=True" under [var]
in /etc/conf/libvirt/qemu.conf - check for spice_tls =1
and in /etc/conf/libvirt/libvirtd.conf - auth_tcp and listen_tcp are not declared (under a
comment).
to verify, restart vdsm service and run - vdsClient -s 0 getVdsCaps [-s for secure]. if
it returns, the configurations are good.
for unsecure connection:
in libvirtd.conf you should have auth_tcp="none" listen_tcp=1 in
/etc/conf/vdsm/vdsm.conf - check that ssl=False in /etc/conf/libvirt/qemu.conf - check for
spice_tls=0
and again, to verify - vdsClient 0 getVdsCaps , if returns we're fine.
Please attach the results.
If it's not the issue, please attach your vdsm.log to check it more specifically.
Regards,
Yaniv Bronhaim.
----- Original Message -----
From: "Sven Knohsalla"
<s.knohsalla(a)netbiscuits.com>
To: users(a)ovirt.org
Sent: Wednesday, May 1, 2013 5:02:07 PM
Subject: [Users] oVirt 3.0 - known issue with live migration
Hi there,
adding a new node to an oVirt 3.0 cluster worked, but migration doesn’t..
(same hardware, some node version 2.3.0)
“Migration failed due to Error: Could not connect to peer host”
(WebGui)
Thread-2474::ERROR::2013-05-01
13:58:08,007::SecureXMLRPCServer::73::root::(handle_error) client
('172.16.101.102', 60836) (vdsm log on target host)
I remember there was a bug in this scenario where I had to uncomment
the line in /etc/libvirt/libvirtd.conf:
listen_tls = 0 --> #listen_tls = 0
Rebooted the new HV in maintenance mode, the config setup persisted,
but the problem also persists…
Unfortunately I had the same issue in the past, but I just documented
the setting in/etc/libvirt/libvirtd.conf
as workaround, so it seems something is still missing…?
DNS & FQDN are setup properly…
Does anybody reminds of this bug and may help me out?
(didn’t find this issue in the mail archive)
Thanks in advance!
Best,
Sven.
Sven Knohsalla | System Administration
Office +49 631 68036 433 | Fax +49 631 68036 111 |E-Mail
s.knohsalla(a)netbiscuits.com | Skype: netbiscuits.admin
Netbiscuits GmbH | Europaallee 10 | 67657 | GERMANY
Register Court: Local Court Kaiserslautern | Commercial Register ID:
HR B
3604
Management Board : Guido Moggert, Michael Neidhöfer, Christian Reitz,
Martin Süß
This message and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom they are addressed.
It may also be privileged or otherwise protected by work product
immunity or other legal rules. Please notify the sender immediately by
e-mail if you have received this e-mail by mistake and delete this
e-mail from your system. If you are not the intended recipient you are
notified that disclosing, copying, distributing or taking any action
in reliance on the contents of this information is strictly prohibited.
Warning: Although Netbiscuits has taken reasonable precautions to
ensure no viruses are present in this email, the company cannot accept
responsibility for any loss or damage arising from the use of this email or
attachments.
Please consider the environment before printing
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users