Hello, I have a newly created datacenter in 3.2.1 with f18 host where ovirtmgmt is set as vlan. host is installed but after some minutes I get this messages:
Host management02 moved to Non-Operational state because interfaces 'em1.311' are down but are needed by networks 'ovirtmgmt' in the current cluster What does 'vdsClient -s 0 getVdsStats' say on vdsm host? Could you
On 04/11/2013 06:20 AM, Gianluca Cecchi wrote: please paste the whole line of 'network = {xxx}' in the output here? Thanks!
from an operating system point of view it seems that all is ok on the host
[root@management02 ~]# ip addr list 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:15:17:b4:99:3c brd ff:ff:ff:ff:ff:ff 3: em2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:15:17:b4:99:3d brd ff:ff:ff:ff:ff:ff inet 213.205.41.202/26 brd 213.205.41.255 scope global em2 4: em1.311@em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master ovirtmgmt state UP link/ether 00:15:17:b4:99:3c brd ff:ff:ff:ff:ff:ff 5: ovirtmgmt: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:15:17:b4:99:3c brd ff:ff:ff:ff:ff:ff inet 10.39.71.12/26 brd 10.39.71.63 scope global ovirtmgmt 7: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 36:98:c3:39:5f:43 brd ff:ff:ff:ff:ff:ff 8: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 9: bond4: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 10: bond1: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 11: bond2: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 12: bond3: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
[root@management02 ~]# ethtool em1 Settings for em1: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes [root@management02 ~]# ethtool em1.311 Settings for em1.311: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: internal Auto-negotiation: on Link detected: yes
On engine [root@management01 ~]# ip addr list 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:15:17:b1:1f:e8 brd ff:ff:ff:ff:ff:ff 3: em2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:15:17:b1:1f:e9 brd ff:ff:ff:ff:ff:ff inet 213.205.41.201/26 brd 213.205.41.255 scope global em2 4: em1.192@em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:15:17:b1:1f:e8 brd ff:ff:ff:ff:ff:ff inet 192.168.230.1/24 brd 192.168.230.255 scope global em1.192 5: em1.311@em1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:15:17:b1:1f:e8 brd ff:ff:ff:ff:ff:ff inet 10.39.71.11/26 brd 10.39.71.63 scope global em1.311
[root@management01 ~]# ethtool em1 Settings for em1: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes [root@management01 ~]# ethtool em1.311 Settings for em1.311: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: internal Auto-negotiation: on Link detected: yes
what can be the cause? what is the check that runs and move the host to non-operational? Thanks Gianluca _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users