--=-kGjQPKOBV63yLQC5f24c Content-Type: text/plain; charset="UTF-8" Content-Transfer-Encoding: quoted-printable Hey, Am Sonntag, den 07.10.2012, 15:29 +0100 schrieb Alexandre Santos:
Hi, I'm trying to install the ovirt-node iso image on a SATA disk and when it gets to the screen where it shows 25% completed the kernel hangs. I can't connect using a serial console to see what has happened. If I reboot using a usb linux disk I see that the SATA disk has been formated and the partitions that existed before disappeared, being there just one partition of type "ee"
Is there any error displayed when kernel hangs at 25%? And it can take some time to pass the 25% (up to ~2min or so).
If I use a 8 GB usb pen-drive instead of the SATA disk, the installation comes to an end and I reboot but then I get some error about not getting /dev/mapper/by-name/Root and the boot fails to a dracut shell. Any ideas?
In the dracut shell, could you run blkid and post the results? Greetings fabian --=-kGjQPKOBV63yLQC5f24c Content-Type: application/pgp-signature; name="signature.asc" Content-Description: This is a digitally signed message part Content-Transfer-Encoding: 7bit -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.12 (GNU/Linux) iQIcBAABAgAGBQJQcn8/AAoJEC9+uOgSHVGUsKgP/3jBB3OMTvO52Lf4lNj+NZvx v8EV1AfHQxbYerjxJq4iSA621nOLqy7MephEQauBmS3EFUgZ8nh19Uosjs97+8Q9 eoNUFQgT7EGDOFKFqMKXls84mGrpRL2B5uwHjzBk0oSQ79Djo9hkOcel/TCMmmYF WYhACgOd431Du6S0EkfV1BX1KbI+Yz/duvgL/BOrKaPCNXhUnOANVLxIvCVufRDo dY5KECqgy3Pwcllnd+GjHbTVB20OX2JHl4HWkMvKkTYiCcVYh1IdqJwuWe12gUrR s96Ew1ATi7EVVyNTgMNRWDIDTVgkiEVZOqn3v0sVQZoM5q6fVLFPzD9Pss6K1HWd x4qjaddcubrOf0aao+seeekgS9ottB+4L3PO7LrheHVRHM3U1wcp8t7Az+NnKeoV XEOU5/9KhySp1gVoyCrdI9DFI3FBRZcf5u28VYJ8JxIb21goCQC5fhsGxtdPDmnz 6H4W4u+kEtgJkyBxYpDcM38c0fELmx5mpyXjsuXtCq6AdrVVcic+ulbwZs3TrIRu ufbVc/QuyYiWjN8mFmCG+MpltadjZ4xE1C6rAZeZq21FL9RPGTJNOL6xxExjZPkn sEt1eCUnkKGP/V4gmbgDt5x0fVeb2pvFGRCG1+ZLY9/C/+kNLfa62zWjFySHqriM cFCnt9pv6XyGCGN+GWGF =6a32 -----END PGP SIGNATURE----- --=-kGjQPKOBV63yLQC5f24c--