12:53 a.m.
Hi Fabian,
Everytime the ovirt node boots up, it adds a route entry that I have to manually remove.
Otherwise it messed up my routing.
How do I modify the boot scripts to automatically remove it?
----- Original Message -----
From: Fabian Deutsch <fabiand(a)redhat.com>
To: David Li <david_li(a)sbcglobal.net>
Cc: "users(a)ovirt.org" <users(a)ovirt.org>
Sent: Monday, October 28, 2013 7:45 AM
Subject: Re: [Users] How to pxeboot ovrit node into memory automatically?
Am Montag, den 28.10.2013, 07:42 -0700 schrieb David Li:
>
> Hi Fabian,
>
> Yes rootpwd worked too! Thanks.
>
> Two new problems:
>
> But I found there is no networking for the stateless node.
> What kernel boot options are used to either use DHCP or statically
configure the IP address for an interface on the node?
>
> I also need to have the sshd enabled. Is there a kernel option for that?
Hey David,
here you can find all the supported boot params in ovirt node:
http://gerrit.ovirt.org/gitweb?p=ovirt-node.git;a=blob;f=scripts/ovirt-in...
Greetings
fabian
> David
>
>
>
> ----- Original Message -----
> > From: Fabian Deutsch <fabiand(a)redhat.com>
> > To: David Li <david_li(a)sbcglobal.net>
> > Cc: "users(a)ovirt.org" <users(a)ovirt.org>
> > Sent: Friday, October 25, 2013 9:10 AM
> > Subject: Re: [Users] How to pxeboot ovrit node into memory
automatically?
> >
> > Am Freitag, den 25.10.2013, 08:57 -0700 schrieb David Li:
> >> Hi Fabian,
> >>
> >> That kernel option worked for me! The node is booted up in RAM.
Thanks!
> >>
> >> My next question is:
> >> How do I specify the root login and passwd as boot parameters?
> >
> > Hey David.
> >
> > Nice that it worked! Were you able to register to the Engine?
> >
> > You can use the adminpw= and rootpw= kernel arguments to set
passwords.
> > use
> > $ openssl passwd -salt 42
> > to create one or two passwords
> >
> > Greetings
> > fabian
> >
> >> David
> >>
> >>
> >>
> >>
> >> ----- Original Message -----
> >> > From: Fabian Deutsch <fabiand(a)redhat.com>
> >> > To: David Li <david_li(a)sbcglobal.net>
> >> > Cc: "users(a)ovirt.org" <users(a)ovirt.org>
> >> > Sent: Thursday, October 24, 2013 11:47 PM
> >> > Subject: Re: [Users] How to pxeboot ovrit node into memory
> > automatically?
> >> >
> >> > Am Donnerstag, den 24.10.2013, 16:26 -0700 schrieb David Li:
> >> >> Hi,
> >> >>
> >> >> I was following the instructions at
> > http://www.ovirt.org/Node_PXE. My goal
> >> > is to use pxeboot (iPXE) to boot the node entirely into RAM
with
> > rootfs. What I
> >> > got now is an installation screen which requires a local
storage. My
> > system has
> >> > no disk and this doesn't quite work for me.
> >> >>
> >> >> What's are the kernel parameters I need to use to
boot the
> > node into
> >> > RAM automatically? I am OK as the first step with a
stateless node.
> >> >
> >> > Hey David,
> >> >
> >> > the stateless mode is currently not completely working with
oVirt
> >> > Engine. That means a Node needs to be approved each time it
boots into
> >> > the stateless mode.
> >> > The stateless mode can be entered by appending stateless to
the
> > default
> >> > kernel arguments.
> >> >
> >> > Greetings
> >> > fabian
> >> >
> >