
Hi Daniel,
I did a lsmod | grep qxl and it returned nothing... did you perhaps mean qla?
[root@ovirt141 ~]# lsmod | grep qla qla2xxx 466573 56
I think that is the one
lsscsi does list all of the LUNs... so that's working!
But nothing in ovirt engine when I try to add a storage domain.
Thanks again, I guess I will try and get a bit further with the installs I have...
Bill
-----Original Message----- From: Daniel Helgenberger [mailto:daniel.helgenberger@m-box.de] Sent: 11 September 2014 11:53 To: Bill Dossett Subject: Re: [ovirt-users] FC QLogic question
On 11.09.2014 12:17, Bill Dossett wrote:
Thanks for responding Daniel. Never mind! I was wondering and thought the message may be irrelevant. But yes, it doesn't appear to be working. When I try to add a FC storage domain, no hosts are showing in the drop down box of hosts. I have loaded the latests ovirtnode (3.4.something.) on two hosts now and neither are working. Lets first try to isolate your FC issure. So you are using the latest ovirt-node? EL6? Keep in mind, the kernel is standard Linux and therefore should support Qlogic adapters out of the box (IMHO they are the best supported HBAs in Linux). Please try a: # lsmod | grep qxl to see whatever the qxl module is loaded. Keep in mind you can run into problems with other conrollers in your host, though I only had this with LSI SAS / FC controllers so far.
Further check on the FC switch if the N port is logged in and the zoning is correct.
Finally, check with # lsscsi if you can see the luns.
Also having a lot of issues with configuring the network. I configure an interface I can ping it, but it shows as unconfigured. on one host I have added it to the manager and I see the interfaces anyway, but on the second host I configure the eth0, I can ping it, it added to the ovirt engine but it shows no NICs. Should I be using an earlier version maybe?
thanks again and best regards.
*Bill Dossett* *Virtualisation Architect* *Pitney Bowes - Tech Central*** 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone(+44) (0)1923 279353 | VOIP: 54739353 Mobile(+44) (0)7775 908612 bill.dossett@pb.com <mailto:bill.dossett@pb.com> www.pb.com <http://www.pb.com/> *In Engineering?**Raise a ticket via Remedy Anywhere [HERE <http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident /newIncident.aspx>]takes less than a minute*
*ManageIQ User Guide available* [*HERE <https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20 v4.pdf>*] *Check out the ManageIQ Blog for recent enhancements and information [HERE] <http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx>*
On Sep 11, 2014, at 10:52 AM, Daniel Helgenberger <daniel.helgenberger@m-box.de <mailto:daniel.helgenberger@m-box.de>> wrote:
Hello Bill,
what are your problems acually? Is fibre channel not working (as expected)?
The log snippet you provided is completly normal and the messages can safely be ignored. This is also unrelated to oVirt but rather CentOS (or the distro you are running) I suppose.
Cheers!
On 11.09.2014 10:51, Bill Dossett wrote:
Hi,
I seem to have run into a problem setting up ovirt with Fibre Channel storage.
I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing
Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/.
Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx
Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x.
Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-00fc:1: ISP2432: PCIe (2.5GT/s x4) @ 0000:0c:00.0 hdma+ host#=1 fw=4.00.26 (2).
Sep 9 08:01:27 localhost kernel: ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
I have googled the firmware error and it says some cards need a firmware flash and some don't. These are pretty standard HBAs so I would think they would be supported out of the box, but maybe not. Looking at trying to add the firmware looked kind of complex - if I need to do this, does anyone know of a nice and easy howto guide on this. I'm just getting started with ovirt and appreciate any help
Thanks
*Bill Dossett*
*Virtualisation Architect*
*Pitney Bowes - Tech Central***
6 Hercules Way, 600 Leavesden Park
Watford, WD25 7GS
Phone(+44) (0)1923 279353 | VOIP: 54739353
Mobile(+44) (0)7775 908612
bill.dossett@pb.com <mailto:bill.dossett@pb.com> <mailto:bill.dossett@pb.com>
www.pb.com <http://www.pb.com> <http://www.pb.com/>
*In Engineering?**Raise a ticket via Remedy Anywhere [HERE <http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incid ent/newIncident.aspx>]takes
less than a minute*
*ManageIQ User Guide available*[*HERE <https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB %20v4.pdf>*]
*Check out the ManageIQ Blog for recent enhancements and information [HERE] <http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.asp x>*
------------------------------------------------------------------- -------------
-- Daniel Helgenberger m box bewegtbild GmbH
P: +49/30/2408781-22 F: +49/30/2408781-10
ACKERSTR. 19 D-10115 BERLIN
www.m-box.de <http://www.m-box.de> www.monkeymen.tv <http://www.monkeymen.tv>
Geschäftsführer: Martin Retschitzegger / Michaela Göllner Handeslregister: Amtsgericht Charlottenburg / HRB 112767
---------------------------------------------------------------------- ----------
-- Daniel Helgenberger m box bewegtbild GmbH
P: +49/30/2408781-22 F: +49/30/2408781-10
ACKERSTR. 19 D-10115 BERLIN
www.m-box.de www.monkeymen.tv
Geschäftsführer: Martin Retschitzegger / Michaela Göllner Handeslregister: Amtsgericht Charlottenburg / HRB 112767
________________________________