Not sure if this would have anything to do with that error on the previous attempt. Even though network config files (in /network-scripts) are set to "ONBOOT=yes" After a reboot, I still need to issue "systemctl restart network.service" otherwise I can not connect to any the 3 hosts? On 2018-05-18 00:46, Simone Tiraboschi wrote:
On Fri, May 18, 2018 at 9:14 AM, <ovirt@fateknollogee.com> wrote:
Simone, do see any other failures before the MAC error? When the deployment failed, I tried to run it again then it gave me the MAC error. The first time it failed there was no error message, it just stopped & said 'deployment failed'
On the previous attempt it failed on 'Add additional gluster hosts to engine' on ovirt-node3.fateknollogee.com [7]; not sure on what really failed there but we need engine.log and host-deploy logs for that host but I suspect you don't have them anymore since they were on that engine VM.
'Add additional gluster hosts to engine' is one of latest steps, anything else before that was fine.
Adding also Gobinda here.
Just as an hint, are you sure that ovirt-node3.fateknollogee.com [7] could be properly resolved on your engine VM?
On 2018-05-18 00:09, Simone Tiraboschi wrote: Hi, it fails due to
ERROR The MAC address '00:16:3E:6A:7A:F9' is in use by another virtual machine.
and this is probably due to a leftover VM from a previous attempt.
It's tracked here: https://bugzilla.redhat.com/show_bug.cgi?id=1576451 [1] and it will be properly fixed with the next release.
In the mean time can you please manually undefine your leftover HostedEngine VM from your env?
/usr/bin/virsh -c qemu:///system?authfile=/etc/ovirt-hosted-engine/virsh_auth.conf undefine HostedEngine
should do the job.
On Fri, May 18, 2018 at 6:46 AM, <ovirt@fateknollogee.com> wrote:
Yesterday, that install failed because I did not have the required 60GB for /var.
Today, I started from scratch & re-installed the oVirt nodes. That install also failed. I've attached the logs via dropbox link
https://www.dropbox.com/s/mnhn5bpuqlsr8ir/ovirt-hosted-engine-setup.zip?dl=0
[2] [1]
On 2018-05-17 01:55, ovirt@fateknollogee.com wrote:
Some good news... Hosted Engine Deployment "preparing the vm" completed. I used a simpler password. When I got the previous errors, my password was 12 characters (upper, lower case & numbers) long with a %% (double percent) before and after the characters. I guess it didn't like the double percent!!! Let me continue, I will report back.
On 2018-05-17 00:30, Simone Tiraboschi wrote: On Thu, May 17, 2018 at 9:16 AM, <ovirt@fateknollogee.com> wrote:
More info: From my ovirt node (host) I can ping 192.168.124.198 If I try to connect via ssh root@192.168.124.198, it asks for a password. The password I used during the hosted engine setup does not work.
Can you please try with a different more robust password? The log file is under /var/log/ovirt-hosted-engine-setup
On 2018-05-16 22:27, ovirt@fateknollogee.com wrote: I will get the logs.
Here is the exact error message: [ ERROR ] fatal: [ovirt-engine.fateknollogee.com [3] [2] [1]]: UNREACHABLE! => {"changed": false, "msg": "Failed to connect to the host via ssh: Warning: Permanently added 'ovirt-engine.fateknollogee.com [3] [2] [1],192.168.124.198' (ECDSA) to
the list of known hosts.\r\nPermission denied (publickey,gssapi-keyex,gssapi-with-mic,password).\r\n", "unreachable": true}
On 2018-05-16 07:04, Simone Tiraboschi wrote: On Wed, May 16, 2018 at 3:36 PM, <ovirt@fateknollogee.com> wrote:
Simone, unfortunately I deleted that install after it failed. I can re-run the install based on the df -h (see previous post) or I can change disks & increase the size of /var then re-run the install. What do you think? The error I was getting said it could not find the hosted engine at vibr0 on 192.168.xxx.xx
On my opinion you could simply retry. Please share your log file it fails again.
On 2018-05-16 06:30, Simone Tiraboschi wrote:
On Wed, May 16, 2018 at 3:25 PM, <ovirt@fateknollogee.com> wrote:
This is what I had. Does this look correct?
Yes, I think so.
can you please share your hosted-engine-setup log file to understand where it's failing?
[root@ovirt-node1 ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/onn_ovirt--node1-ovirt--node--ng--4.2.3--0.20180515.0+1 14G 1.8G 12G 14% / devtmpfs 32G 0 32G 0% /dev tmpfs 32G 8.0K 32G 1% /dev/shm tmpfs 32G 18M 32G 1% /run tmpfs 32G 0 32G 0% /sys/fs/cgroup /dev/sda1 976M 207M 702M 23% /boot /dev/mapper/onn_ovirt--node1-home 976M 2.6M 907M 1% /home /dev/mapper/onn_ovirt--node1-tmp 976M 2.8M 906M 1% /tmp /dev/mapper/onn_ovirt--node1-var 15G 112M 14G 1% /var /dev/mapper/onn_ovirt--node1-var_log 7.8G 42M 7.3G 1% /var/log /dev/mapper/onn_ovirt--node1-var_log_audit 2.0G 6.3M 1.8G 1% /var/log/audit /dev/mapper/onn_ovirt--node1-var_crash 9.8G 37M 9.2G 1% /var/crash tmpfs 6.3G 0 6.3G 0% /run/user/0
On 2018-05-16 06:14, Simone Tiraboschi wrote: On Wed, May 16, 2018 at 2:52 PM, <ovirt@fateknollogee.com> wrote:
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[4] [3] [2] [1] [1] [1] says: Important: If you are also installing the oVirt Engine Virtual Appliance for self-hosted engine installation, the /var partition must be at least 60 GB.
The appliance disk is shipped as a qcow2 image: 4 GB should be enough.
Back to the drawing board, I certainly failed to read that!!
On 2018-05-16 02:37, Andrea Dell'Amico wrote: On 16 May 2018, at 09:42, Simone Tiraboschi <stirabos@redhat.com> wrote:
On Tue, May 15, 2018 at 6:31 PM, <ovirt@fateknollogee.com> wrote:
Engine network config error
Following this blog post:
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster...
[5] [4]
[3] [2] [2] [2]
[1]
I get an error saying the hosted engine setup is "trying" to use vibr0 (192.168.xxx.x) even though I have the bridge interface set to "eno1"
Regardless of whether the Edit Hosts File is checked or unchecked, it overwrites my engine IP entry from 10.50.235.x to 192.168.xxx.x
The same thing happens whether I set the engine IP to Static or DHCP (I don't have DNS, I'm using static entries in /etc/hosts).
Any ideas it "insists" on using "vibr0" instead of "eno1"?
Hi, up to this point is absolutely fine: in the new node zero deployment flow, hosted-engine-setup bootstraps a local VM with an engine there to use that engine to configure the rest of the system (storage, network...). That bootstrap VM runs over default natted libvirt network, that's why you see vibr0 and 192.168.xxx.x at that stage.
If you are facing any issue, it's definitively not there.
Yes, the blog post describes the 4.2.{0,1} behaviour while the local VM is a change introduced in 4.2.2. I faced a similar error and in my case the VM creation failed because there was not enough space in /var/tmp. It wasn’t a problem before, because the engine VM was created directly on top of a gluster volume.
Andrea -- Andrea Dell'Amico http://adellam. sevenseas.org/ [6] [5] [4] [3] [3] [3] [2]
Links: ------ [1]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster...
[5] [4] [3] [2] [2] [2] [2] http://sevenseas.org/ _______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org
Links: ------ [1]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[4] [3] [2] [1] [1] [2]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster...
[5] [4] [3] [2] [2] [3] http://sevenseas.org/
Links: ------ [1]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[4] [3] [2] [1] [2]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster...
[5] [4] [3] [2] [3] http://sevenseas.org/
Links: ------ [1]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[4] [3] [2] [2]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster...
[5] [4] [3] [3] http://sevenseas.org/ _______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org _______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org
Links: ------ [1] http://ovirt-engine.fateknollogee.com [3] [2] [2]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[4] [3] [3]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster...
[5] [4] [4] http://sevenseas.org/ _______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org
Links: ------ [1]
https://www.dropbox.com/s/mnhn5bpuqlsr8ir/ovirt-hosted-engine-setup.zip?dl=0
[2] [2] http://ovirt-engine.fateknollogee.com [3] [3]
https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/
[4] [4]
https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster...
[5] [5] http://sevenseas.org/
Links: ------ [1] https://bugzilla.redhat.com/show_bug.cgi?id=1576451 [2] https://www.dropbox.com/s/mnhn5bpuqlsr8ir/ovirt-hosted-engine-setup.zip?dl=0 [3] http://ovirt-engine.fateknollogee.com [4] https://www.ovirt.org/documentation/install-guide/chap-System_Requirements/ [5] https://www.ovirt.org/blog/2018/02/up-and-running-with-ovirt-4-2-and-gluster... [6] http://sevenseas.org/ [7] http://ovirt-node3.fateknollogee.com