Fabian, Thanks for the debugging steps. I did the steps for all three scenarios and created a bug for this: https://bugzilla.redhat.com/show_bug.cgi?id=1010221 Kind Regards, Jorick On Thu, 2013-09-19 at 15:27 +0200, Fabian Deutsch wrote:
Am Donnerstag, den 19.09.2013, 15:12 +0200 schrieb Jorick Astrego:
Hmmm, I'm beginning to suspect the LSI MegaRaid chips.
I replaced the SSD of the first node with a brand new Samsung 256GB SSD and the second node with a 1TB HDD.
When I change the SWAP size on both nodes to 4GB, it fails to install the bootloader.
When I leave everything on default and just continue the steps, I get an "error 30 read-only filesystem" on BOTH nodes.
When I choose Other drive and select /dev/sda, I get the ValueError exception.
So I'm kinda stuck :-&
Our RAID chip is LSI 2108 SAS
Hey Jorick,
thanks for the informations from this and your last e-mail. I think we need some deeper debugging, could you please do the following to get more debugging informations: 1. Boot the ISO as usual 2. When the installer TUI comes up, press F" and drop to a shell 3. Set a password for root 4. Now run: ovirt-node-installer --debug This will run the installer in debug mode (writing tons of infos to /var/log/ovirt-node.debug.log). 5. Continue the installation as usual until you reach a problem, then:
6. Switch to a second console and login (the setup tui should come up) 7. Drop to shell by pressing F2 8. Please send the files * /var/log/ovirt-node.debug.log * /var/log/ovirt.log * /tmp/ovirt.log (if available)
That would really help us to find out what the problem is.
I think we should also open a bug for this.
Thanks and greetings fabian
Kind regards,
Jorick Astrego
-----Original Message-----
From: "Jorick Astrego" <j.astrego@netbulae.eu> To: "Fabian Deutsch" <fabiand@redhat.com> Cc: users@ovirt.org Date: 19/09/2013 12:53 Subject: Re: [Users] Exception: ValueError("invalid literal for int() with base 10: ' '", )
Hi,
I'm using ovirt-node-iso-3.0.1-1.0.2.vdsm.fc19.iso and I tried reproducing on two nodes. I thought maybe the first node's SSD had failed.
See screenshots attached (they are very small).
As the Local disk first only reported 1GB, i used Other device /dev/sda and got the ValueError (xxx_144.png).
When using Local disk, I get a 'Read-only file system' error. (xxx_145.png)
This is on two identical nodes with a SSD connected through LSI MegaRAID. I could try it without RAID, but I'll have to visit the datacenter and reflash the LSI firmware for this.
Both nodes had an older 2.6 node image running on it before.
After a full RAID re-initialization that produced no errors, I now get yet another faillure:
"Exception: RuntimeError('Failed to set install bootloader'.)" (xxx_147.png)
Can it be the SSD or RAID controller? I could swap out the SSD for a 2.5 hdd to test it out.
Thanks in advance!
Jorick Astrego Netbulae B.V.
-----Original Message-----
From: "Fabian Deutsch" <fabiand@redhat.com> To: "Jorick Astrego" <j.astrego@netbulae.eu> Cc: users@ovirt.org Date: 18/09/2013 15:49 Subject: Re: [Users] Exception: ValueError("invalid literal for int() with base 10: ' '", )
Hey,
Am Mittwoch, den 18.09.2013, 15:35 +0200 schrieb Jorick Astrego:
I'm trying to deploy the ovirt node 3.0.1-1.0.2 image. Because we only have a small SSD and don't need overcommit I changed the swap file size to a smaller value.
While installing I now get the following error and have to reboot:
Exception: ValueError("invalid literal for int() with base 10: ' '",)
I tried to reproduce this problem but couldn't trigger it using: 1. Enter the storage sizes page 2. Changed the swap value to 100 (allowed value depends on your hosts mem size) 3. Saved page, went through the next pages and installed
Could you explain in detail how you triggered this problem? And are you using the fc19 or el6 iso?
Greetings fabian
If I don't change the value of the swap, I get a message that the installer is unable to format/partition the disk.
Kind regards,
Jorick Astrego
_______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users