Re: [Users] Network profile lost after host edit

I built a new Engine Server on 3.3.2-1.el6, rebuilt my VM's and I no longer see the issue. All is now working as expected. Simon -----Original Message----- From: Simon Barrett Sent: 08 January 2014 08:50 To: Lior Vernia; Itamar Heim Cc: users(a)ovirt.org Subject: RE: [Users] Network profile lost after host edit To test this further I setup another 3.3.2-1.el6 ovirt-engine. I'm not seeing the same problem on the new engine. I'm going to try and move all configuration/VM's etc from the problem ovirt-engine install to the new one to see if the problem re-appears. I'll let you know how it goes. Simon -----Original Message----- From: Lior Vernia [mailto:lvernia@redhat.com] Sent: 08 January 2014 06:02 To: Itamar Heim Cc: Simon Barrett; users(a)ovirt.org Subject: Re: [Users] Network profile lost after host edit On 07/01/14 23:16, Itamar Heim wrote: > On 01/07/2014 08:59 AM, Lior Vernia wrote: >> Hi Simon, >> >> Thank you so much for tracking this down. I'm currently immersed in >> oVirt 3.4 feature stuff, but I just wanted to let you know I saw this >> and am planning to take care of it; I'll take a look in a week or two >> when things calm down. >> >> The bad news are, I suspect there will be no workaround other than >> upgrading to the next version that will include the fix (likely 3.3.3). >> > > is there an ovirt bug targeted to 3.3.3 tracking this? > I'll open one as soon as I test the issue. Unless Simon would like to pick up the gauntlet and open one on bugzilla.redhat.com?... >> Yours, Lior. >> >> On 06/01/14 12:21, Simon Barrett wrote: >>> I am now able to reproduce the problem where network profile >>> definitions are lost on VM edit. >>> >>> - Create VM >>> - From the "Network Interfaces" tab, click on "New" and assign the >>> ovirtmgt profile to nic1 >>> - Edit VM, from the "nic1" drop down select another profile and >>> click OK >>> - Edit the same VM again and nic1 lists as <Empty> >>> >>> I upgraded to 3.3.2-1.el6 and still see the problem. >>> >>> As ever, any help is very much appreciated. >>> >>> Thanks, >>> >>> Simon >>> >>> >>> -----Original Message----- >>> From: users-bounces(a)ovirt.org [mailto:users-bounces@ovirt.org] On >>> Behalf Of Simon Barrett >>> Sent: 12 December 2013 21:53 >>> To: Lior Vernia >>> Cc: users(a)ovirt.org >>> Subject: Re: [Users] Network profile lost after host edit >>> >>> Lior, >>> >>> I'm running 3.3.1. >>> >>> I think it may be related to how I created the VM's. Another VM >>> created using the blank template works fine and the network config >>> displays correctly when I click on edit. >>> >>> The problem VM's were created with a different template. I'll dig a >>> bit further to see if I can narrow it down any further. >>> >>> I don't have to click show advanced to exhibit the problem. >>> >>> Thanks for the response >>> >>> Simon >>> >>>> On 12 Dec 2013, at 16:44, "Lior Vernia" <lvernia(a)redhat.com&gt; wrote: >>>> >>>> Hi Simon, >>>> >>>> I apologize for the delay in my response. I've worked quite a bit >>>> on that part of the dialog since oVirt 3.3, and while it was quite >>>> buggy I haven't encountered this exact issue you're describing. It >>>> does remind me of one bug though; could it be that pressing the >>>> "Show Advanced Options" is what triggers the strange behavior? >>>> >>>> What version of oVirt engine are you running? Both 3.3.1 and 3.3.2 >>>> should be quite stable as far as this dialog is concerned, so >>>> upgrading might be a good idea. >>>> >>>> As for workarounds, it sounds like a GUI issue so I don't think >>>> there's anything you can do apart from upgrading the engine. >>>> >>>> Yours, Lior. >>>> >>>>> On 11/12/13 13:40, Simon Barrett wrote: >>>>> I have a problem where VM network profiles are lost when editing a >>>>> host. >>>>> E.G. >>>>> >>>>> >>>>> >>>>> * VM is running fine on the correct network. Network >>>>> Interfaces >>>>> tab shows "nic1" and "Network Name" shows the correct network profile. >>>>> >>>>> * I shutdown the VM then right click and Edit. >>>>> >>>>> * The General settings for the node shows "nic1 <Empty>". If I >>>>> then edit config, something like increasing memory or changing CPU >>>>> cores then click on OK, the VM configuration is saved without a >>>>> network profile. >>>>> >>>>> * When I boot the VM I cannot connect to it. >>>>> >>>>> * I then have to edit the node again configure back in the >>>>> correct network profile. >>>>> >>>>> >>>>> >>>>> Does anyone know if this is a known issue? If not, any suggestions >>>>> as to how I correct this so that the original network profile >>>>> definition is retained after an edit? >>>>> >>>>> >>>>> >>>>> Many thanks, >>>>> >>>>> >>>>> >>>>> Simon >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> Users mailing list >>>>> Users(a)ovirt.org >>>>> http://lists.ovirt.org/mailman/listinfo/users >>>>> >>> _______________________________________________ >>> Users mailing list >>> Users(a)ovirt.org >>> http://lists.ovirt.org/mailman/listinfo/users >>> >> _______________________________________________ >> Users mailing list >> Users(a)ovirt.org >> http://lists.ovirt.org/mailman/listinfo/users >> >