1:22 p.m.
On Mon, Dec 10, 2018 at 10:56 AM Eitan Raviv <eraviv(a)redhat.com> wrote:
Ran into the same issue with oVirt Node 4.2.7.1 when installing as a
virtual guest.
Didi,
Can you point us in the right direction?
Sorry, I didn't try this myself recently and not sure about the details.
Obviously it should all be automatic.
Adding Simone.
I suggest to open a bug about this and attach relevant logs
(hosted-engine-setup logs, engine (and engine-setup) logs, vdsm, etc).
Best regards,
Thanks
On Mon, Dec 10, 2018 at 2:23 AM Vincent Royer <vincent(a)epicenergy.ca> wrote:
>
> This happened to me too.
>
> The NIC doesn't come "up" on the first boot, even though it was
initiated during the setup. DHCP or static makes no difference to this situation. iirc I
used nmtui to bring the interface up and verify the hostname. Can't do it in cockpit
without the interface being up...
>
> Once you're in the engine you can initialize and add the rest of the required
nics.
>
> I'm not sure if this is as designed or a bug, but it last happened to me on
4.2.5, and was the same process on my 3 hosts.
>
>
> On Sun, Dec 9, 2018 at 12:14 AM Eitan Raviv <eraviv(a)redhat.com> wrote:
>>
>> On Thu, Dec 6, 2018 at 7:10 PM Stefan Wolf <shb256(a)gmail.com> wrote:
>> >
>> > Hello,
>> >
>> >
>> >
>> > I ve downloaded an installed OVIRT NODE 4.2.7.1.
>> >
>> > During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp,
both work)
>> >
>>
>> how did you setup the static ip? did you use Cockpit?
>>
>>
>> > The installation passes and after the reboot ovirt node starts without any
problems.
>> >
>> > BUT the network is not configured.
>>
>> what do you mean by 'network is not configured'? the static IP is not
>> assigned to your selected NIC or sth else?
>>
>>
>> >
>> > I know https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/
and I know
>> >
>> > https://www.ovirt.org/documentation/admin-guide/chap-Hosts/
>> >
>> >
>> >
>> > and now I am between these two documents
>> >
>> > oVirt is installed but network is not configured to add it to datacenter
>> >
>> >
>> >
>> > of course I know the scripts under /etc/sysconfig/network-scripts
>> >
>> > do I really have do edit it manuel?
>> >
>> >
>> >
>> > if I change ip in command line
>> >
>> > ip a add … dev..
>> >
>> > and ip route add …
>> >
>> > it fails to add node to datacenter
>> >
>> >
>> >
>> > - with one of the last version I ‘ve added the IP address in bash
>> >
>> > - added the host to datacenter,
>> >
>> > - after reboot readd the ip address in bash after reboot
>> >
>> > - an then I could change network settings in oVirt Manger
>> >
>> >
>> >
>> > What is best practices for adding a node to datacenter when the ip address
is not assigned after installation
>> >
>> >
>> >
>> > Thx shb
>> >
>> > _______________________________________________
>> > Users mailing list -- users(a)ovirt.org
>> > To unsubscribe send an email to users-leave(a)ovirt.org
>> > Privacy Statement: https://www.ovirt.org/site/privacy-policy/
>> > oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
>> > List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/TH5MRXJUU4S...
>> _______________________________________________
>> Users mailing list -- users(a)ovirt.org
>> To unsubscribe send an email to users-leave(a)ovirt.org
>> Privacy Statement: https://www.ovirt.org/site/privacy-policy/
>> oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
>> List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/PULDN5JRT6P...
--
Didi