Usually I would blacklist the Gluster devices by creating the necessary stanzas in
/etc/multipath/conf.d/blacklist.conf
This way you will keep the situation simple.
For your problem, it's hard to odentify the problem based on the e-mails.What are your
symptoms ?
To debug GlusterFS, it is good to start from the brick logs (/var/log/gluster/bricks) and
the current heal status. On a 3-way replica volume heals should be resolved by GlusterFS -
if not, there is a bug.
Best Regards,Strahil Nikolov
Best Regards,Strahil Nikolov
On Tue, May 31, 2022 at 16:32, jb<jonbae77(a)gmail.com> wrote: I still have the
same problems, but it look like that the errors comes a
bit less often.
I'm starting now to migrate the disk images to a NFS storage. When there
is no other way, I would recreate the glusterFS cluster.
The problem I have is, that I don't know where is the root of this
problem and if recreating would fix the issue in longer terms.
Am 29.05.22 um 20:26 schrieb Nir Soffer:
On Sun, May 29, 2022 at 9:03 PM Jonathan Baecker
<jonbae77(a)gmail.com> wrote:
> Am 29.05.22 um 19:24 schrieb Nir Soffer:
>
> On Sun, May 29, 2022 at 7:50 PM Jonathan Baecker <jonbae77(a)gmail.com> wrote:
>
> Hello everybody,
>
> we run a 3 node self hosted cluster with GlusterFS. I had a lot of problem upgrading
ovirt from 4.4.10 to 4.5.0.2 and now we have cluster instability.
>
> First I will write down the problems I had with upgrading, so you get a bigger
picture:
>
> engine update when fine
> But nodes I could not update because of wrong version of imgbase, so I did a manual
update to 4.5.0.1 and later to 4.5.0.2. First time after updating it was still booting
into 4.4.10, so I did a reinstall.
> Then after second reboot I ended up in the emergency mode. After a long searching I
figure out that lvm.conf using use_devicesfile now but there it uses the wrong filters. So
I comment out this and add the old filters back. This procedure I have done on all 3
nodes.
>
> When use_devicesfile (default in 4.5) is enabled, lvm filter is not
> used. During installation
> the old lvm filter is removed.
>
> Can you share more info on why it does not work for you?
>
> The problem was, that the node could not mount the gluster volumes anymore and ended
up in emergency mode.
>
> - output of lsblk
>
> NAME MAJ:MIN RM SIZE RO TYPE
MOUNTPOINT
> sda 8:0 0 1.8T 0 disk
> `-XA1920LE10063_HKS028AV 253:0 0 1.8T 0 mpath
> |-gluster_vg_sda-gluster_thinpool_gluster_vg_sda_tmeta 253:16 0 9G 0 lvm
> | `-gluster_vg_sda-gluster_thinpool_gluster_vg_sda-tpool 253:18 0 1.7T 0 lvm
> | |-gluster_vg_sda-gluster_thinpool_gluster_vg_sda 253:19 0 1.7T 1 lvm
> | |-gluster_vg_sda-gluster_lv_data 253:20 0 100G 0 lvm
/gluster_bricks/data
> | `-gluster_vg_sda-gluster_lv_vmstore 253:21 0 1.6T 0 lvm
/gluster_bricks/vmstore
> `-gluster_vg_sda-gluster_thinpool_gluster_vg_sda_tdata 253:17 0 1.7T 0 lvm
> `-gluster_vg_sda-gluster_thinpool_gluster_vg_sda-tpool 253:18 0 1.7T 0 lvm
> |-gluster_vg_sda-gluster_thinpool_gluster_vg_sda 253:19 0 1.7T 1 lvm
> |-gluster_vg_sda-gluster_lv_data 253:20 0 100G 0 lvm
/gluster_bricks/data
> `-gluster_vg_sda-gluster_lv_vmstore 253:21 0 1.6T 0 lvm
/gluster_bricks/vmstore
> sr0 11:0 1 1024M 0 rom
> nvme0n1 259:0 0 238.5G 0 disk
> |-nvme0n1p1 259:1 0 1G 0 part
/boot
> |-nvme0n1p2 259:2 0 134G 0 part
> | |-onn-pool00_tmeta 253:1 0 1G 0 lvm
> | | `-onn-pool00-tpool 253:3 0 87G 0 lvm
> | | |-onn-ovirt--node--ng--4.5.0.2--0.20220513.0+1 253:4 0 50G 0 lvm /
> | | |-onn-pool00 253:7 0 87G 1 lvm
> | | |-onn-home 253:8 0 1G 0 lvm
/home
> | | |-onn-tmp 253:9 0 1G 0 lvm
/tmp
> | | |-onn-var 253:10 0 15G 0 lvm
/var
> | | |-onn-var_crash 253:11 0 10G 0 lvm
/var/crash
> | | |-onn-var_log 253:12 0 8G 0 lvm
/var/log
> | | |-onn-var_log_audit 253:13 0 2G 0 lvm
/var/log/audit
> | | |-onn-ovirt--node--ng--4.5.0.1--0.20220511.0+1 253:14 0 50G 0 lvm
> | | `-onn-var_tmp 253:15 0 10G 0 lvm
/var/tmp
> | |-onn-pool00_tdata 253:2 0 87G 0 lvm
> | | `-onn-pool00-tpool 253:3 0 87G 0 lvm
> | | |-onn-ovirt--node--ng--4.5.0.2--0.20220513.0+1 253:4 0 50G 0 lvm /
> | | |-onn-pool00 253:7 0 87G 1 lvm
> | | |-onn-home 253:8 0 1G 0 lvm
/home
> | | |-onn-tmp 253:9 0 1G 0 lvm
/tmp
> | | |-onn-var 253:10 0 15G 0 lvm
/var
> | | |-onn-var_crash 253:11 0 10G 0 lvm
/var/crash
> | | |-onn-var_log 253:12 0 8G 0 lvm
/var/log
> | | |-onn-var_log_audit 253:13 0 2G 0 lvm
/var/log/audit
> | | |-onn-ovirt--node--ng--4.5.0.1--0.20220511.0+1 253:14 0 50G 0 lvm
> | | `-onn-var_tmp 253:15 0 10G 0 lvm
/var/tmp
> | `-onn-swap 253:5 0 20G 0 lvm
[SWAP]
> `-nvme0n1p3 259:3 0 95G 0 part
> `-gluster_vg_nvme0n1p3-gluster_lv_engine 253:6 0 94G 0 lvm
/gluster_bricks/engine
>
> - The old lvm filter used, and why it was needed
>
> filter =
["a|^/dev/disk/by-id/lvm-pv-uuid-Nn7tZl-TFdY-BujO-VZG5-EaGW-5YFd-Lo5pwa$|",
"a|^/dev/disk/by-id/lvm-pv-uuid-Wcbxnx-2RhC-s1Re-s148-nLj9-Tr3f-jj4VvE$|",
"a|^/dev/disk/by-id/lvm-pv-uuid-lX51wm-H7V4-3CTn-qYob-Rkpx-Tptd-t94jNL$|",
"r|.*|"]
>
> I don't remember exactly any more why it was needed, but without the node was not
working correctly. I think I even used vdsm-tool config-lvm-filter.
I think that if you list the devices in this filter:
ls -lh /dev/disk/by-id/lvm-pv-uuid-Nn7tZl-TFdY-BujO-VZG5-EaGW-5YFd-Lo5pwa \
/dev/disk/by-id/lvm-pv-uuid-Wcbxnx-2RhC-s1Re-s148-nLj9-Tr3f-jj4VvE
\
/dev/disk/by-id/lvm-pv-uuid-lX51wm-H7V4-3CTn-qYob-Rkpx-Tptd-t94jNL
You will see that these are the devices used by these vgs:
gluster_vg_sda, gluster_vg_nvme0n1p3, onn
> - output of vdsm-tool config-lvm-filter
>
> Analyzing host...
> Found these mounted logical volumes on this host:
>
> logical volume: /dev/mapper/gluster_vg_nvme0n1p3-gluster_lv_engine
> mountpoint: /gluster_bricks/engine
> devices: /dev/nvme0n1p3
>
> logical volume: /dev/mapper/gluster_vg_sda-gluster_lv_data
> mountpoint: /gluster_bricks/data
> devices: /dev/mapper/XA1920LE10063_HKS028AV
>
> logical volume: /dev/mapper/gluster_vg_sda-gluster_lv_vmstore
> mountpoint: /gluster_bricks/vmstore
> devices: /dev/mapper/XA1920LE10063_HKS028AV
>
> logical volume: /dev/mapper/onn-home
> mountpoint: /home
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-ovirt--node--ng--4.5.0.2--0.20220513.0+1
> mountpoint: /
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-swap
> mountpoint: [SWAP]
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-tmp
> mountpoint: /tmp
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-var
> mountpoint: /var
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-var_crash
> mountpoint: /var/crash
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-var_log
> mountpoint: /var/log
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-var_log_audit
> mountpoint: /var/log/audit
> devices: /dev/nvme0n1p2
>
> logical volume: /dev/mapper/onn-var_tmp
> mountpoint: /var/tmp
> devices: /dev/nvme0n1p2
>
> Configuring LVM system.devices.
> Devices for following VGs will be imported:
>
> gluster_vg_sda, gluster_vg_nvme0n1p3, onn
>
> To properly configure the host, we need to add multipath
> blacklist in /etc/multipath/conf.d/vdsm_blacklist.conf:
>
> blacklist {
> wwid "eui.0025388901b1e26f"
> }
>
>
> Configure host? [yes,NO]
If you run "vdsm-tool config-lvm-filter" and confirm with "yes", I
think all the vgs
will be imported properly into lvm devices file.
I don't think it will solve the storage issues you have since Feb
2022, but at least
you will have a standard configuration and the next upgrade will not revert your
local settings.
> If using lvm devices does not work for you, you can enable the lvm
> filter in vdsm configuration
> by adding a drop-in file:
>
> $ cat /etc/vdsm/vdsm.conf.d/99-local.conf
> [lvm]
> config_method = filter
>
> And run:
>
> vdsm-tool config-lvm-filter
>
> to configure the lvm filter in the best way for vdsm. If this does not create
> the right filter we would like to know why, but in general you should use
> lvm devices since it avoids the trouble of maintaining the filter and dealing
> with upgrades and user edited lvm filter.
>
> If you disable use_devicesfile, the next vdsm upgrade will enable it
> back unless
> you change the configuration.
>
> I would be happy to just use the default, when there is a way to make use_devicesfile
to wok.
>
> Also even if you disable use_devicesfile in lvm.conf, vdsm still use
> --devices instead
> of filter when running lvm commands, and lvm commands run by vdsm ignore your
> lvm filter since the --devices option overrides the system settings.
>
> ...
>
> I notice some unsync volume warning, but because I had this in the past to, after
upgrading, I though after some time they will disappear. The next day there still where
there, so I decided to put the nodes again in the maintenance mode and restart the
glusterd service. After some time the sync warnings where gone.
>
> Not clear what these warnings are, I guess Gluster warning?
>
> Yes was Gluster warnings under Storage -> Volumes it was saying that some entries
are unsync.
>
> So now the actual problem:
>
> Since this time the cluster is unstable. I get different errors and warning, like:
>
> VM [name] is not responding
> out of nothing HA VM gets migrated
> VM migration can fail
> VM backup with snapshoting and export take very long
>
> How do you backup the vms? do you sue a backup application? how is it
> configured?
>
> I use a self made plython script, which uses the rest api. I create a snapshot from
the VM, build a new VM from that snapshot and move the new one to the export domain.
This is not very efficient - this copy the entire vm at the point of
time of the snapshot
and then copy it again to the export domain.
If you use a backup application supporting the incremental backup API,
the first full backup
will copy the entire vm once, but later incremental backup will copy
only the changes
since the last backup.
> VMs are getting very slow some times
> Storage domain vmstore experienced a high latency of 9.14251
> ovs|00001|db_ctl_base|ERR|no key "dpdk-init" in Open_vSwitch record
"." column other_config
> 489279 [1064359]: s8 renewal error -202 delta_length 10 last_success 489249
> 444853 [2243175]: s27 delta_renew read timeout 10 sec offset 0
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/ids
> 471099 [2243175]: s27 delta_renew read timeout 10 sec offset 0
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/ids
> many of: 424035 [2243175]: s27 delta_renew long write time XX sec
>
> All these issues tell use that your storage is not working correctly.
>
> sanlock.log is full of renewal errors form May:
>
> $ grep 2022-05- sanlock.log | wc -l
> 4844
>
> $ grep 2022-05- sanlock.log | grep 'renewal error' | wc -l
> 631
>
> But there is lot of trouble from earlier months:
>
> $ grep 2022-04- sanlock.log | wc -l
> 844
> $ grep 2022-04- sanlock.log | grep 'renewal error' | wc -l
> 29
>
> $ grep 2022-03- sanlock.log | wc -l
> 1609
> $ grep 2022-03- sanlock.log | grep 'renewal error' | wc -l
> 483
>
> $ grep 2022-02- sanlock.log | wc -l
> 826
> $ grep 2022-02- sanlock.log | grep 'renewal error' | wc -l
> 242
>
> Here sanlock log looks healthy:
>
> $ grep 2022-01- sanlock.log | wc -l
> 3
> $ grep 2022-01- sanlock.log | grep 'renewal error' | wc -l
> 0
>
> $ grep 2021-12- sanlock.log | wc -l
> 48
> $ grep 2021-12- sanlock.log | grep 'renewal error' | wc -l
> 0
>
> vdsm log shows that 2 domains are not accessible:
>
> $ grep ERROR vdsm.log
> 2022-05-29 15:07:19,048+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
> (monitor:511)
> 2022-05-29 16:33:59,049+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
> (monitor:511)
> 2022-05-29 16:34:39,049+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
> (monitor:511)
> 2022-05-29 17:21:39,050+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
> (monitor:511)
> 2022-05-29 17:55:59,712+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/metadata
> (monitor:511)
> 2022-05-29 17:56:19,711+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/metadata
> (monitor:511)
> 2022-05-29 17:56:39,050+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_data/de5f4123-0fac-4238-abcf-a329c142bd47/dom_md/metadata
> (monitor:511)
> 2022-05-29 17:56:39,711+0200 ERROR (check/loop) [storage.monitor]
> Error checking path
>
/rhev/data-center/mnt/glusterSD/onode1.example.org:_vmstore/3cf83851-1cc8-4f97-8960-08a60b9e25db/dom_md/metadata
> (monitor:511)
>
> You need to find what is the issue with your Gluster storage.
>
> I hope that Ritesh can help debug the issue with Gluster.
>
> Nir
>
> I'm worry that I do something, that it makes it even more worst, and I hove not
idea what's the problem. To me it looks not exactly like a problem with data
inconsistencies.
The problem is that your Gluster storage is not healthy, and reading
and writing to it times out.
Please keep users(a)ovirt.org CC when you reply. Gluster storage is very
popular in this mailing list
and you may get useful help from other users.
Nir
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement:
https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/VBYRVRQPXXD...