Re: [Users] vlan on mgmt network

From: jplorier(a)gmail.com To: "Peter Styk" <polfilm(a)gmail.com&gt; Cc: "William Kwan" <potatok(a)yahoo.com&gt;, "users" <users(a)ovirt.org&gt; Sent: Sunday, January 19, 2014 3:31:31 AM Subject: Re: [Users] vlan on mgmt network Hi Peter, Try to check if ovirmgmt is defined in the vlan you desire (or without vlan). Maybe when you sync ovirt is trying to configure the network with options different from what you desire. I never got ovirt to finish properly to install a host, it fails to get ovirtmgmt working right so I always manually configure the vlan interfaces and the ovirtmgmt bridge in the hosts. You can get your host back if you manually correct the network, also you may take a look of what ovirt configured to try to find out if something is not set properly in the network definition. Regards El ene 18, 2014 7:56 PM, "Peter Styk" < polfilm(a)gmail.com > escribió: On 18 January 2014 17:11, Itamar Heim < iheim(a)redhat.com > wrote: On 01/18/2014 04:52 PM, Peter Styk wrote: So I got ovirtmgmt VM ticked off. Had to remove it from all VM's then tried to add new Logical network to eth0 by drag & drop but refused since ovirtmgmt was out of sync. So I synced it. ....and that's how I lost access to my hosted remote system. End of story. So that's it I guess, automated install doesn't work (during switch network goes dead and doesn't come back remote access is lost) so I found manual way that works. But then I need to sync it to get my ovirtmgmt not to be a VM network. And even if its not to get another network on the interface i need to sync it..... this sounds like a bug - can you provide clear reproduction steps? Reproduction steps are in network configuration alone. After installing Engine, i have to set up network to the config listed here: http://styk.tv/wp-content/uploads/2014/01/oVirtHosted1_almost_working.png . Unfortunately can't rely on engine-vdsm duo to help out. Anything above the host line on the diagram is physical setup and is the only configuration that doesn't disconnect me from the net. Only thing missing on the diagram is ifcfg-eth0 has also HWADDR attribute with MAC address of physical eth0 device. Once this survives service network restart I can proceed to VDSM install and then its straight forward....that is until I'm trying to SYNC ovirtmgmt on host inside. I should mention after ovirt engine is working I destroy default cluster and create new local one. Obviously I cannot access logs since access to host is no longer but entire setup is scripted including provisioning so I can easily rebuild entire setup within 15 or so minutes by running a script. Anyone who would like to benefit from my findings can use this script and gain access to my host and learn with me on how to overcome this. Script will provision the host (fresh os install), log in, get the files: ifcfg-eth0, ifcfg-ovirtmgmt, ifcfg-ovirtmgmt-range0, ovrit_answers and route-ovirtmgmt, then install epel 6-8, install pgp, localinstall ovirt-el6.10-1. install bridge-utils, upgrade, set hostname, then after reboot ssh alive, set local data,images,iso folders, install ovrit-engine, set ipv4 forwarding and proxy_arp=1, restart-network, and run engine-setup with ovirt_answers including cli and stop iptables as engine and vdsm rules still prevent connection if on. that's it. working system in 15 mins still to do is engine-api calls to create local cluster, join engine with vdsm local and setup private network with pfSense instance as router/nat/dhcp for 10.0.0.0/24 Peter _______________________________________________ Users mailing list Users(a)ovirt.org http://lists.ovirt.org/mailman/listinfo/users