8:27 a.m.
Am Donnerstag, den 19.09.2013, 15:12 +0200 schrieb Jorick Astrego:
Hmmm, I'm beginning to suspect the LSI MegaRaid chips.
I replaced the SSD of the first node with a brand new Samsung 256GB SSD and the second
node with a 1TB HDD.
When I change the SWAP size on both nodes to 4GB, it fails to install the bootloader.
When I leave everything on default and just continue the steps, I get an "error 30
read-only filesystem" on BOTH nodes.
When I choose Other drive and select /dev/sda, I get the ValueError exception.
So I'm kinda stuck :-&
Our RAID chip is LSI 2108 SAS
Hey Jorick,
thanks for the informations from this and your last e-mail.
I think we need some deeper debugging, could you please do the following
to get more debugging informations:
1. Boot the ISO as usual
2. When the installer TUI comes up, press F" and drop to a shell
3. Set a password for root
4. Now run: ovirt-node-installer --debug
This will run the installer in debug mode (writing tons of infos
to /var/log/ovirt-node.debug.log).
5. Continue the installation as usual until you reach a problem, then:
6. Switch to a second console and login (the setup tui should come up)
7. Drop to shell by pressing F2
8. Please send the files
* /var/log/ovirt-node.debug.log
* /var/log/ovirt.log
* /tmp/ovirt.log (if available)
That would really help us to find out what the problem is.
I think we should also open a bug for this.
Thanks and greetings
fabian
Kind regards,
Jorick Astrego
-----Original Message-----
> From: "Jorick Astrego" <j.astrego(a)netbulae.eu>
> To: "Fabian Deutsch" <fabiand(a)redhat.com>
> Cc: users(a)ovirt.org
> Date: 19/09/2013 12:53
> Subject: Re: [Users] Exception: ValueError("invalid literal for int() with base
10: ' '", )
>
> Hi,
>
> I'm using ovirt-node-iso-3.0.1-1.0.2.vdsm.fc19.iso and I tried reproducing on
two nodes. I thought maybe the first node's SSD had failed.
>
> See screenshots attached (they are very small).
>
> As the Local disk first only reported 1GB, i used Other device /dev/sda and got the
ValueError (xxx_144.png).
>
> When using Local disk, I get a 'Read-only file system' error. (xxx_145.png)
>
> This is on two identical nodes with a SSD connected through LSI MegaRAID. I could
try it without RAID, but I'll have to visit the datacenter and reflash the LSI
firmware for this.
>
> Both nodes had an older 2.6 node image running on it before.
>
> After a full RAID re-initialization that produced no errors, I now get yet another
faillure:
>
> "Exception: RuntimeError('Failed to set install bootloader'.)"
(xxx_147.png)
>
> Can it be the SSD or RAID controller? I could swap out the SSD for a 2.5 hdd to test
it out.
>
> Thanks in advance!
>
> Jorick Astrego
> Netbulae B.V.
>
>
> -----Original Message-----
> > From: "Fabian Deutsch" <fabiand(a)redhat.com>
> > To: "Jorick Astrego" <j.astrego(a)netbulae.eu>
> > Cc: users(a)ovirt.org
> > Date: 18/09/2013 15:49
> > Subject: Re: [Users] Exception: ValueError("invalid literal for int() with
base 10: ' '", )
> >
> > Hey,
> >
> > Am Mittwoch, den 18.09.2013, 15:35 +0200 schrieb Jorick Astrego:
> > > I'm trying to deploy the ovirt node 3.0.1-1.0.2 image. Because we only
have a small SSD and don't need overcommit I changed the swap file size to a smaller
value.
> > >
> > > While installing I now get the following error and have to reboot:
> > >
> > > Exception: ValueError("invalid literal for int() with base 10: '
'",)
> >
> > I tried to reproduce this problem but couldn't trigger it using:
> > 1. Enter the storage sizes page
> > 2. Changed the swap value to 100 (allowed value depends on your hosts
> > mem size)
> > 3. Saved page, went through the next pages and installed
> >
> > Could you explain in detail how you triggered this problem?
> > And are you using the fc19 or el6 iso?
> >
> > Greetings
> > fabian
> >
> >
> > > If I don't change the value of the swap, I get a message that the
installer is unable to format/partition the disk.
> > >
> > > Kind regards,
> > >
> > > Jorick Astrego
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Users mailing list
> > > Users(a)ovirt.org
> > > http://lists.ovirt.org/mailman/listinfo/users
>
>
>
_______________________________________________
> Users mailing list
> Users(a)ovirt.org
> http://lists.ovirt.org/mailman/listinfo/users
>