7:31 p.m.
Ok here are the log files. It installs most packages and then hangs up on
libjpeg? libjpeg is installed including dev package. This is a bare-metal
node running fedora 16 with vdsm packages installed from repo. Your node
.iso 2.2.1 does not initialize realtek nic cards so I can not use that.
The 2.2.1 .iso sees the nic card but that is it. So I went the route of
installing the full fedora 16 distro and installing vdsm packages from
repo. I am bridged correctly and ssl=false in the vdsm.conf. Now when I
go to the ovirt management gui and install the node it fails at this step.
I can see the node in ovirt management gui just an fyi so not a problem
with detection. It seems that the vdsm server will not start due to
libjpeg install failure but mabey I am wrong.
Let me know what you think,
Dominic
On Sun, Jan 15, 2012 at 4:11 AM, Doron Fediuck <dfediuck(a)redhat.com> wrote:
On Saturday 14 January 2012 16:04:27 Dominic Kaiser wrote:
> I have recently set up an ovirt engine server and one host. The ovirt
> engine server was installed on a small Intell Atom quad core with 4 gigs
of
> ram box. The ovirt engine server is running on Fedora 16 and engine was
> installed from rpms after I added the repo. Also I have installed one
host
> or node if you prefer That is an AMD quad core with 8 gigs of ram and has
> virtualization. I have tried installing from ovirt node 2.2.1 iso but
> ethernet card can not be intialized even though it is detected. This is
a
> realtek card and it shows up fine in fedora 16. The iso is still a bit
> buggy for me so I tried installing fedora 16 and then the vdsm rpm
packages
> from repository. I have correctly set up a bridge on fedora 16 and by
the
> way your instructions are wrong for bridge setup. I will be glad to send
> you guys a correct config for the wiki if neccessary for fedora 16. Vdsm
> is running and I installed host from the ovirt gui by adding new host
> entered ip config an.d it appeared in the ovirt web manager. What it
does
> not do properly is install on the Ovirt web manager I get installing then
> it says install failed. I have tried reinstalling from the ovirt web
> manager to no avail. The wiki is a good start but directions are
lacking I
> must say. Is there any more config that needs to be done on the
vdsm.conf
> file in etc/vdsm/vdsm.conf or does it just "detect" when the Ovirt web
> manager calls for it? I am probably missing something on my end I am
> guessing. Also what log files would be helpful to look at? I will be
> trying this out also on a new asus server with two 8 core amd opterons
and
> 32 gigs of ram shortly so I will let you know how that goes also. This
> project is great I just need to get a working host and I want to write a
> simpler install write up for this project that in my opinion is what it
is
> lacking.
>
> Let me know,
Hi Dominic,
If I get you right, you have set a bridge and manually installed vdsm using
RPM's.
When you add a host from the web UI, it's actually trying to do what you
did, but it should be a problem. So... let's try to figure out the real
issue;
If you SSH into your vdsm host (node), you'll find under /tmp the
installation
log files.
Please verify there's no sensitive data there, and send to list.
We'll continue based on the logs.
Doron.
--
Dominic Kaiser
Greater Boston Vineyard
Director of Operations
cell: 617-230-1412
fax: 617-252-0238
email: dominic(a)bostonvineyard.org