5:39 p.m.
Hello,
I'd like to know if there is a way to configure ovirt (oVirt Engine
Version: 3.5.0.1-1.el6) to NOT migrate VM's when there is a problem with
attached storage.
Scenario - our storage array that hosts all our VM disks failed. When that
happened, ovirt attempted to migrate running VM's from one host to another.
Unfortunately this left many of the VM's in a 'migrating to' state that
could only be resolved by restarting the HV's
I'd prefer to have ovirt simply hang the VM's until disk IO returns.
Is this possible?
***
*Mark Steele*
CIO / VP Technical Operations | TelVue Corporation
TelVue - We Share Your Vision
800.885.8886 x128 | msteele(a)telvue.com | http://www.telvue.com
twitter: http://twitter.com/telvue | facebook:
https://www.facebook.com/telvue
6:40 p.m.
New subject: Disabling migration when there is a problem with storage
Hi Mark,
You can disable VM migration:
When editing a vm, in the 'Host' tab there is 'Migration option' drop-down
where you can choose 'Do not allow migration' or 'Allow manual migration
only'.
Hope this helps.
Regards,
Ala
----- Original Message -----
From: "Mark Steele" <msteele(a)telvue.com>
To: users(a)ovirt.org
Sent: Wednesday, February 3, 2016 4:39:43 PM
Subject: [ovirt-users] Disabling migration when there is a problem with storage
Hello,
I'd like to know if there is a way to configure ovirt ( oVirt Engine Version:
3.5.0.1-1.el6) to NOT migrate VM's when there is a problem with attached
storage.
Scenario - our storage array that hosts all our VM disks failed. When that
happened, ovirt attempted to migrate running VM's from one host to another.
Unfortunately this left many of the VM's in a 'migrating to' state that
could only be resolved by restarting the HV's
I'd prefer to have ovirt simply hang the VM's until disk IO returns.
Is this possible?
***
Mark Steele
CIO / VP Technical Operations | TelVue Corporation
TelVue - We Share Your Vision
800.885.8886 x128 | msteele(a)telvue.com | http://www.telvue.com
twitter: http://twitter.com/telvue | facebook:
https://www.facebook.com/telvue
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
6:45 p.m.
When a storage error occurs, VMs should pause, not migrate. However, if the
VMs were io-idle, then pause (qemu EIO) might have not been triggered
before hosts started dropping into non-op.
...which triggered a migration storm for HA-enabled VMs, racing with VMs
pausing somehow (can't tell without diving into the logs for sure).
I haven't seen it happen in any of my setups, probably a new issue
On Wed, Feb 3, 2016 at 9:39 AM, Mark Steele <msteele(a)telvue.com> wrote:
Hello,
I'd like to know if there is a way to configure ovirt (oVirt Engine
Version: 3.5.0.1-1.el6) to NOT migrate VM's when there is a problem with
attached storage.
Scenario - our storage array that hosts all our VM disks failed. When that
happened, ovirt attempted to migrate running VM's from one host to another.
Unfortunately this left many of the VM's in a 'migrating to' state that
could only be resolved by restarting the HV's
I'd prefer to have ovirt simply hang the VM's until disk IO returns.
Is this possible?
***
*Mark Steele*
CIO / VP Technical Operations | TelVue Corporation
TelVue - We Share Your Vision
800.885.8886 x128 | msteele(a)telvue.com | http://www.telvue.com
twitter: http://twitter.com/telvue | facebook:
https://www.facebook.com/telvue
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
3215
days inactive
3215
days old
2 comments
3 participants
participants (3)
-
Ala Hino -
Dan Yasny -
Mark Steele