11:06 a.m.
Hello,
TL; DR : qcow2 images keep getting corrupted. Any workaround?
Long version:
This discussion has already been launched by me on the oVirt and on
qemu-block mailing list, under similar circumstances but I learned
further things since months and here are some informations :
- We are using 2 oVirt 3.6.7.5-1.el7.centos datacenters, using CentOS
7.{2,3} hosts
- Hosts :
- CentOS 7.2 1511 :
- Kernel = 3.10.0 327
- KVM : 2.3.0-31
- libvirt : 1.2.17
- vdsm : 4.17.32-1
- CentOS 7.3 1611 :
- Kernel 3.10.0 514
- KVM : 2.3.0-31
- libvirt 2.0.0-10
- vdsm : 4.17.32-1
- Our storage is 2 Equallogic SANs connected via iSCSI on a dedicated
network
- Depends on weeks, but all in all, there are around 32 hosts, 8 storage
domains and for various reasons, very few VMs (less than 200).
- One peculiar point is that most of our VMs are provided an additional
dedicated network interface that is iSCSI-connected to some volumes of
our SAN - these volumes not being part of the oVirt setup. That could
lead to a lot of additional iSCSI traffic.
From times to times, a random VM appears paused by oVirt.
Digging into the oVirt engine logs, then into the host vdsm logs, it
appears that the host considers the qcow2 image as corrupted.
Along what I consider as a conservative behavior, vdsm stops any
interaction with this image and marks it as paused.
Any try to unpause it leads to the same conservative pause.
After having found (https://access.redhat.com/solutions/1173623) the
right logical volume hosting the qcow2 image, I can run qemu-img check
on it.
- On 80% of my VMs, I find no errors.
- On 15% of them, I find Leaked cluster errors that I can correct using
"qemu-img check -r all"
- On 5% of them, I find Leaked clusters errors and further fatal errors,
which can not be corrected with qemu-img.
In rare cases, qemu-img can correct them, but destroys large parts of
the image (becomes unusable), and on other cases it can not correct them
at all.
Months ago, I already sent a similar message but the error message was
about No space left on device
(https://www.mail-archive.com/qemu-block@gnu.org/msg00110.html).
This time, I don't have this message about space, but only corruption.
I kept reading and found a similar discussion in the Proxmox group :
https://lists.ovirt.org/pipermail/users/2018-February/086750.html
https://forum.proxmox.com/threads/qcow2-corruption-after-snapshot-or-heav...
What I read similar to my case is :
- usage of qcow2
- heavy disk I/O
- using the virtio-blk driver
In the proxmox thread, they tend to say that using virtio-scsi is the
solution. Having asked this question to oVirt experts
(https://lists.ovirt.org/pipermail/users/2018-February/086753.html) but
it's not clear the driver is to blame.
I agree with the answer Yaniv Kaul gave to me, saying I have to properly
report the issue, so I'm longing to know which peculiar information I
can give you now.
As you can imagine, all this setup is in production, and for most of the
VMs, I can not "play" with them. Moreover, we launched a campaign of
nightly stopping every VM, qemu-img check them one by one, then boot.
So it might take some time before I find another corrupted image.
(which I'll preciously store for debug)
Other informations : We very rarely do snapshots, but I'm close to
imagine that automated migrations of VMs could trigger similar behaviors
on qcow2 images.
Last point about the versions we use : yes that's old, yes we're
planning to upgrade, but we don't know when.
Regards,
--
Nicolas ECARNOT
6:59 a.m.
On Feb 7, 2018 7:08 PM, "Nicolas Ecarnot" <nicolas(a)ecarnot.net> wrote:
Hello,
TL; DR : qcow2 images keep getting corrupted. Any workaround?
Long version:
This discussion has already been launched by me on the oVirt and on
qemu-block mailing list, under similar circumstances but I learned further
things since months and here are some informations :
- We are using 2 oVirt 3.6.7.5-1.el7.centos datacenters, using CentOS
7.{2,3} hosts
- Hosts :
- CentOS 7.2 1511 :
- Kernel = 3.10.0 327
- KVM : 2.3.0-31
- libvirt : 1.2.17
- vdsm : 4.17.32-1
- CentOS 7.3 1611 :
- Kernel 3.10.0 514
- KVM : 2.3.0-31
- libvirt 2.0.0-10
- vdsm : 4.17.32-1
All are somewhat old releases. I suggest upgrading to the latest RHEL and
qemu-kvm bits.
Later on, upgrade oVirt.
Y.
- Our storage is 2 Equallogic SANs connected via iSCSI on a dedicated
network
- Depends on weeks, but all in all, there are around 32 hosts, 8 storage
domains and for various reasons, very few VMs (less than 200).
- One peculiar point is that most of our VMs are provided an additional
dedicated network interface that is iSCSI-connected to some volumes of our
SAN - these volumes not being part of the oVirt setup. That could lead to a
lot of additional iSCSI traffic.
From times to times, a random VM appears paused by oVirt.
Digging into the oVirt engine logs, then into the host vdsm logs, it
appears that the host considers the qcow2 image as corrupted.
Along what I consider as a conservative behavior, vdsm stops any
interaction with this image and marks it as paused.
Any try to unpause it leads to the same conservative pause.
After having found (https://access.redhat.com/solutions/1173623) the right
logical volume hosting the qcow2 image, I can run qemu-img check on it.
- On 80% of my VMs, I find no errors.
- On 15% of them, I find Leaked cluster errors that I can correct using
"qemu-img check -r all"
- On 5% of them, I find Leaked clusters errors and further fatal errors,
which can not be corrected with qemu-img.
In rare cases, qemu-img can correct them, but destroys large parts of the
image (becomes unusable), and on other cases it can not correct them at all.
Months ago, I already sent a similar message but the error message was
about No space left on device (https://www.mail-archive.com/
qemu-block(a)gnu.org/msg00110.html).
This time, I don't have this message about space, but only corruption.
I kept reading and found a similar discussion in the Proxmox group :
https://lists.ovirt.org/pipermail/users/2018-February/086750.html
https://forum.proxmox.com/threads/qcow2-corruption-after-
snapshot-or-heavy-disk-i-o.32865/page-2
What I read similar to my case is :
- usage of qcow2
- heavy disk I/O
- using the virtio-blk driver
In the proxmox thread, they tend to say that using virtio-scsi is the
solution. Having asked this question to oVirt experts (
https://lists.ovirt.org/pipermail/users/2018-February/086753.html) but it's
not clear the driver is to blame.
I agree with the answer Yaniv Kaul gave to me, saying I have to properly
report the issue, so I'm longing to know which peculiar information I can
give you now.
As you can imagine, all this setup is in production, and for most of the
VMs, I can not "play" with them. Moreover, we launched a campaign of
nightly stopping every VM, qemu-img check them one by one, then boot.
So it might take some time before I find another corrupted image.
(which I'll preciously store for debug)
Other informations : We very rarely do snapshots, but I'm close to imagine
that automated migrations of VMs could trigger similar behaviors on qcow2
images.
Last point about the versions we use : yes that's old, yes we're planning
to upgrade, but we don't know when.
Regards,
--
Nicolas ECARNOT
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
7:38 a.m.
This is a multi-part message in MIME format.
--------------1BC2811328971F9BAD7C7EDB
Content-Type: text/plain; charset=utf-8; format=flowed
Content-Transfer-Encoding: 8bit
Le 08/02/2018 à 13:59, Yaniv Kaul a écrit :
On Feb 7, 2018 7:08 PM, "Nicolas Ecarnot" <nicolas(a)ecarnot.net
<mailto:nicolas@ecarnot.net>> wrote:
Hello,
TL; DR : qcow2 images keep getting corrupted. Any workaround?
Long version:
This discussion has already been launched by me on the oVirt and
on qemu-block mailing list, under similar circumstances but I
learned further things since months and here are some informations :
- We are using 2 oVirt 3.6.7.5-1.el7.centos datacenters, using
CentOS 7.{2,3} hosts
- Hosts :
- CentOS 7.2 1511 :
- Kernel = 3.10.0 327
- KVM : 2.3.0-31
- libvirt : 1.2.17
- vdsm : 4.17.32-1
- CentOS 7.3 1611 :
- Kernel 3.10.0 514
- KVM : 2.3.0-31
- libvirt 2.0.0-10
- vdsm : 4.17.32-1
All are somewhat old releases. I suggest upgrading to the latest RHEL
and qemu-kvm bits.
Later on, upgrade oVirt.
Y.
Hello Yaniv,
We could discuss for hours about the fact that CentOS 7.3 was released
in January 2017, thus not that old.
And also discuss for hours explaining the gap between developers' will
to push their freshest releases and the curb we - industry users - put
on adopting such new versions. In my case, the virtualization
infrastructure is just one of the +30 domains I have to master everyday,
and the more stable the better.
In the setup described previously, the qemu qcow2 images were correct,
then not. We did not change anything. We have to find a workaround and
we need your expertise.
Not understanding the cause of the corruption threatens us to the same
situation in oVirt 4.2.
--
Nicolas Ecarnot
--------------1BC2811328971F9BAD7C7EDB
Content-Type: text/html; charset=utf-8
Content-Transfer-Encoding: 8bit
<html>
<head>
<meta http-equiv="Content-Type" content="text/html;
charset=utf-8">
</head>
<body text="#000000" bgcolor="#FFFFFF">
<div class="moz-cite-prefix">Le 08/02/2018 à 13:59, Yaniv Kaul a
écrit :<br>
</div>
<blockquote type="cite"
cite="mid:CAJgorsb_we+ZEu=m1aeh=e_jaiXqf4P09SyEHVdC8V-S+ZoTFg@mail.gmail.com">
<div dir="auto">
<div><br>
<div class="gmail_extra"><br>
<div class="gmail_quote">On Feb 7, 2018 7:08 PM,
"Nicolas
Ecarnot" <<a href="mailto:nicolas@ecarnot.net"
moz-do-not-send="true">nicolas(a)ecarnot.net</a>&gt;
wrote:<br type="attribution">
<blockquote class="quote" style="margin:0 0 0
.8ex;border-left:1px #ccc
solid;padding-left:1ex">Hello,<br>
<br>
TL; DR : qcow2 images keep getting corrupted. Any
workaround?<br>
<br>
Long version:<br>
This discussion has already been launched by me on the
oVirt and on qemu-block mailing list, under similar
circumstances but I learned further things since months
and here are some informations :<br>
<br>
- We are using 2 oVirt 3.6.7.5-1.el7.centos datacenters,
using CentOS 7.{2,3} hosts<br>
- Hosts :<br>
- CentOS 7.2 1511 :<br>
- Kernel = 3.10.0 327<br>
- KVM : 2.3.0-31<br>
- libvirt : 1.2.17<br>
- vdsm : 4.17.32-1<br>
- CentOS 7.3 1611 :<br>
- Kernel 3.10.0 514<br>
- KVM : 2.3.0-31<br>
- libvirt 2.0.0-10<br>
- vdsm : 4.17.32-1<br>
</blockquote>
</div>
</div>
</div>
<div dir="auto"><br>
</div>
<div dir="auto">All are somewhat old releases. I suggest
upgrading to the latest RHEL and qemu-kvm bits. </div>
<div dir="auto"><br>
</div>
<div dir="auto">Later on, upgrade oVirt. </div>
<div dir="auto">Y. </div>
</div>
</blockquote>
Hello Yaniv,<br>
<br>
We could discuss for hours about the fact that CentOS 7.3 was
released in January 2017, thus not that old.<br>
And also discuss for hours explaining the gap between developers'
will to push their freshest releases and the curb we - industry
users - put on adopting such new versions. In my case, the
virtualization infrastructure is just one of the +30 domains I have
to master everyday, and the more stable the better.<br>
In the setup described previously, the qemu qcow2 images were
correct, then not. We did not change anything. We have to find a
workaround and we need your expertise.<br>
<br>
Not understanding the cause of the corruption threatens us to the
same situation in oVirt 4.2.<br>
<br>
-- <br>
Nicolas Ecarnot<br>
</body>
</html>
--------------1BC2811328971F9BAD7C7EDB--
3:41 a.m.
New subject: [Qemu-block] qcow2 images corruption
Am 07.02.2018 um 18:06 hat Nicolas Ecarnot geschrieben:
TL; DR : qcow2 images keep getting corrupted. Any workaround?
Not without knowing the cause.
The first thing to make sure is that the image isn't touched by a second
process while QEMU is running a VM. The classic one is using 'qemu-img
snapshot' on the image of a running VM, which is instant corruption (and
newer QEMU versions have locking in place to prevent this), but we have
seen more absurd cases of things outside QEMU tampering with the image
when we were investigating previous corruption reports.
This covers the majority of all reports, we haven't had a real
corruption caused by a QEMU bug in ages.
After having found (https://access.redhat.com/solutions/1173623) the
right
logical volume hosting the qcow2 image, I can run qemu-img check on it.
- On 80% of my VMs, I find no errors.
- On 15% of them, I find Leaked cluster errors that I can correct using
"qemu-img check -r all"
- On 5% of them, I find Leaked clusters errors and further fatal errors,
which can not be corrected with qemu-img.
In rare cases, qemu-img can correct them, but destroys large parts of the
image (becomes unusable), and on other cases it can not correct them at all.
It would be good if you could make the 'qemu-img check' output available
somewhere.
It would be even better if we could have a look at the respective image.
I seem to remember that John (CCed) had a few scripts to analyse
corrupted qcow2 images, maybe we would be able to see something there.
What I read similar to my case is :
- usage of qcow2
- heavy disk I/O
- using the virtio-blk driver
In the proxmox thread, they tend to say that using virtio-scsi is the
solution. Having asked this question to oVirt experts
(https://lists.ovirt.org/pipermail/users/2018-February/086753.html) but it's
not clear the driver is to blame.
This seems very unlikely. The corruption you're seeing is in the qcow2
metadata, not only in the guest data. If anything, virtio-scsi exercises
more qcow2 code paths than virtio-blk, so any potential bug that affects
virtio-blk should also affect virtio-scsi, but not the other way around.
I agree with the answer Yaniv Kaul gave to me, saying I have to
properly
report the issue, so I'm longing to know which peculiar information I can
give you now.
To be honest, debugging corruption after the fact is pretty hard. We'd
need the 'qemu-img check' output and ideally the image to do anything,
but I can't promise that anything would come out of this.
Best would be a reproducer, or at least some operation that you can link
to the appearance of the corruption. Then we could take a more targeted
look at the respective code.
As you can imagine, all this setup is in production, and for most of
the
VMs, I can not "play" with them. Moreover, we launched a campaign of nightly
stopping every VM, qemu-img check them one by one, then boot.
So it might take some time before I find another corrupted image.
(which I'll preciously store for debug)
Other informations : We very rarely do snapshots, but I'm close to imagine
that automated migrations of VMs could trigger similar behaviors on qcow2
images.
To my knowledge, oVirt only uses external snapshots and creates them
with QMP. This should be perfectly safe because from the perspective of
the qcow2 image being snapshotted, it just means that it gets no new
write requests.
Migration is something more involved, and if you could relate the
problem to migration, that would certainly be something to look into. In
that case, it would be important to know more about the setup, e.g. is
it migration with shared or non-shared storage?
Last point about the versions we use : yes that's old, yes
we're planning to
upgrade, but we don't know when.
That would be helpful, too. Nothing is more frustrating that debugging a
bug in an old version only to find that it's already fixed in the
current version (well, except maybe debugging and finding nothing).
Kevin
9:26 a.m.
New subject: [Qemu-block] qcow2 images corruption
Hello Kevin,
Le 13/02/2018 à 10:41, Kevin Wolf a écrit :
Am 07.02.2018 um 18:06 hat Nicolas Ecarnot geschrieben:
> TL; DR : qcow2 images keep getting corrupted. Any workaround?
Not without knowing the cause.
Actually, my main concern is mostly about finding the cause rather than
correcting my corrupted VMs.
Another way to say it : I prefer to help oVirt than help myself.
The first thing to make sure is that the image isn't touched by a
second
process while QEMU is running a VM.
Indeed, I read some BZ about this issue : they were raised by a user who
ran some qemu-img commands on a "mounted" image, thus leading to some
corruption.
In my case, I'm not playing with this, and the corrupted VMs were only
touched by classical oVirt actions.
The classic one is using 'qemu-img
snapshot' on the image of a running VM, which is instant corruption (and
newer QEMU versions have locking in place to prevent this), but we have
seen more absurd cases of things outside QEMU tampering with the image
when we were investigating previous corruption reports.
This covers the majority of all reports, we haven't had a real
corruption caused by a QEMU bug in ages.
May I ask after what QEMU version this kind of locking has been added.
As I wrote, our oVirt setup is 3.6 so not recent.
> After having found (https://access.redhat.com/solutions/1173623) the right
> logical volume hosting the qcow2 image, I can run qemu-img check on it.
> - On 80% of my VMs, I find no errors.
> - On 15% of them, I find Leaked cluster errors that I can correct using
> "qemu-img check -r all"
> - On 5% of them, I find Leaked clusters errors and further fatal errors,
> which can not be corrected with qemu-img.
> In rare cases, qemu-img can correct them, but destroys large parts of the
> image (becomes unusable), and on other cases it can not correct them at all.
It would be good if you could make the 'qemu-img check' output available
somewhere.
See attachment.
It would be even better if we could have a look at the respective image.
I seem to remember that John (CCed) had a few scripts to analyse
corrupted qcow2 images, maybe we would be able to see something there.
I just exported it like this :
qemu-img convert /dev/the_correct_path /home/blablah.qcow2.img
The resulting file is 32G and I need an idea to transfer this img to you.
> What I read similar to my case is :
> - usage of qcow2
> - heavy disk I/O
> - using the virtio-blk driver
>
> In the proxmox thread, they tend to say that using virtio-scsi is the
> solution. Having asked this question to oVirt experts
> (https://lists.ovirt.org/pipermail/users/2018-February/086753.html) but it's
> not clear the driver is to blame.
This seems very unlikely. The corruption you're seeing is in the qcow2
metadata, not only in the guest data.
Are you saying:
- the corruption is in the metadata and in the guest data
OR
- the corruption is only in the metadata
?
If anything, virtio-scsi exercises
more qcow2 code paths than virtio-blk, so any potential bug that affects
virtio-blk should also affect virtio-scsi, but not the other way around.
I get that.
> I agree with the answer Yaniv Kaul gave to me, saying I have to properly
> report the issue, so I'm longing to know which peculiar information I can
> give you now.
To be honest, debugging corruption after the fact is pretty hard. We'd
need the 'qemu-img check' output
Done.
and ideally the image to do anything,
I remember some Redhat people once gave me a temporary access to put
heavy file on some dedicated server. Is it still possible?
but I can't promise that anything would come out of this.
Best would be a reproducer, or at least some operation that you can link
to the appearance of the corruption. Then we could take a more targeted
look at the respective code.
Sure.
Alas I find no obvious pattern leading to corruption :
From the guest side, it appeared with windows 2003, 2008, 2012, linux
centOS 6 and 7. It appeared with virtio-blk; and I changed some VMs to
used virtio-scsi but it's too soon to see appearance of corruption in
that case.
As I said, I'm using snapshots VERY rarely, and our versions are too old
so we do them the cold way only (VM shutdown). So very safely.
The "weirdest" thing we do is to migrate VMs : you see how conservative
we are!
> As you can imagine, all this setup is in production, and for most
of the
> VMs, I can not "play" with them. Moreover, we launched a campaign of
nightly
> stopping every VM, qemu-img check them one by one, then boot.
> So it might take some time before I find another corrupted image.
> (which I'll preciously store for debug)
>
> Other informations : We very rarely do snapshots, but I'm close to imagine
> that automated migrations of VMs could trigger similar behaviors on qcow2
> images.
To my knowledge, oVirt only uses external snapshots and creates them
with QMP. This should be perfectly safe because from the perspective of
the qcow2 image being snapshotted, it just means that it gets no new
write requests.
Migration is something more involved, and if you could relate the
problem to migration, that would certainly be something to look into. In
that case, it would be important to know more about the setup, e.g. is
it migration with shared or non-shared storage?
I'm 99% sure the corrupted VMs have never see a snapshot, and 99% sure
they have been migrated at most once.
For me *this* is the track to follow.
We have 2 main 3.6 oVirt DCs each having 4 dedicated LUNs, connected via
iSCSI. Two SANs are serving those volumes. These are Equallogic and the
setup of each volume contains a check saying :
Access type : "Shared"
http://psonlinehelp.equallogic.com/V5.0/Content/V5TOC/Allowing_or_disallo...
(shared access to the iSCSI target from multiple initiators)
To be honest, I've never been comfortable with this point:
- In a complete different context, I'm using it to allow two files
servers to publish an OCFS2 volume embedded in a clustered-LVM. It is
absolutely reliable as *c*LVM and OCFS2 are explicitly written to manage
concurrent access.
- In the case of oVirt, we are here allowing tens of hosts to connect to
the same LUN. This LUN is then managed by a classical LVM setup, but I
see here no notion of concurrent access management. To date, I still
haven't understood how was managed these concurrent access to the same
LUN with no crash.
I hope I won't find no skeletons in the closet.
> Last point about the versions we use : yes that's old, yes
we're planning to
> upgrade, but we don't know when.
That would be helpful, too. Nothing is more frustrating that debugging a
bug in an old version only to find that it's already fixed in the
current version (well, except maybe debugging and finding nothing).
Kevin
Exact, but as I wrote to Yaniv, it would be sad to setup a brand new 4.2
DC and to face the bad old issues.
For the record, I just finished to setup another 4.2 DC, but it'll be
long before I could apply to it a similar workload as the 3.6 production
site.
--
Nicolas ECARNOT
10:35 a.m.
New subject: [Qemu-block] qcow2 images corruption
Le 13/02/2018 à 16:26, Nicolas Ecarnot a écrit :
> It would be good if you could make the 'qemu-img check'
output available
> somewhere.
I found this :
https://github.com/ShijunDeng/qcow2-dump
and the transcript (beautiful colors when viewed with "more") is attached :
--
Nicolas ECARNOT
5:01 p.m.
New subject: [Qemu-block] qcow2 images corruption
On 02/13/2018 04:41 AM, Kevin Wolf wrote:
Am 07.02.2018 um 18:06 hat Nicolas Ecarnot geschrieben:
> TL; DR : qcow2 images keep getting corrupted. Any workaround?
Not without knowing the cause.
The first thing to make sure is that the image isn't touched by a second
process while QEMU is running a VM. The classic one is using 'qemu-img
snapshot' on the image of a running VM, which is instant corruption (and
newer QEMU versions have locking in place to prevent this), but we have
seen more absurd cases of things outside QEMU tampering with the image
when we were investigating previous corruption reports.
This covers the majority of all reports, we haven't had a real
corruption caused by a QEMU bug in ages.
> After having found (https://access.redhat.com/solutions/1173623) the right
> logical volume hosting the qcow2 image, I can run qemu-img check on it.
> - On 80% of my VMs, I find no errors.
> - On 15% of them, I find Leaked cluster errors that I can correct using
> "qemu-img check -r all"
> - On 5% of them, I find Leaked clusters errors and further fatal errors,
> which can not be corrected with qemu-img.
> In rare cases, qemu-img can correct them, but destroys large parts of the
> image (becomes unusable), and on other cases it can not correct them at all.
It would be good if you could make the 'qemu-img check' output available
somewhere.
It would be even better if we could have a look at the respective image.
I seem to remember that John (CCed) had a few scripts to analyse
corrupted qcow2 images, maybe we would be able to see something there.
Hi! I did write a pretty simplistic tool for trying to tell the shape of
a corruption at a glance. It seems to work pretty similarly to the other
tool you already found, but it won't hurt anything to run it:
https://github.com/jnsnow/qcheck
(Actually, that other tool looks like it has an awful lot of options.
I'll have to check it out.)
It can print a really upsetting amount of data (especially for very
corrupt images), but in the default case, the simple setting should do
the trick just fine.
You could always put the output from this tool in a pastebin too; it
might help me visualize the problem a bit more -- I find seeing the
exact offsets and locations of where all the various tables and things
to be pretty helpful.
You can also always use the "deluge" option and compress it if you want,
just don't let it print to your terminal:
jsnow@probe (dev) ~/s/qcheck> ./qcheck -xd
/home/bos/jsnow/src/qemu/bin/git/install_test_f26.qcow2 > deluge.log;
and ls -sh deluge.log
4.3M deluge.log
but it compresses down very well:
jsnow@probe (dev) ~/s/qcheck> 7z a -t7z -m0=ppmd deluge.ppmd.7z deluge.log
jsnow@probe (dev) ~/s/qcheck> ls -s deluge.ppmd.7z
316 deluge.ppmd.7z
So I suppose if you want to send along:
(1) The basic output without any flags, in a pastebin
(2) The zipped deluge output, just in case
and I will try my hand at guessing what went wrong.
(Also, maybe my tool will totally choke for your image, who knows. It
hasn't received an overwhelming amount of testing apart from when I go
to use it personally and inevitably wind up displeased with how it
handles certain situations, so ...)
> What I read similar to my case is :
> - usage of qcow2
> - heavy disk I/O
> - using the virtio-blk driver
>
> In the proxmox thread, they tend to say that using virtio-scsi is the
> solution. Having asked this question to oVirt experts
> (https://lists.ovirt.org/pipermail/users/2018-February/086753.html) but it's
> not clear the driver is to blame.
This seems very unlikely. The corruption you're seeing is in the qcow2
metadata, not only in the guest data. If anything, virtio-scsi exercises
more qcow2 code paths than virtio-blk, so any potential bug that affects
virtio-blk should also affect virtio-scsi, but not the other way around.
> I agree with the answer Yaniv Kaul gave to me, saying I have to properly
> report the issue, so I'm longing to know which peculiar information I can
> give you now.
To be honest, debugging corruption after the fact is pretty hard. We'd
need the 'qemu-img check' output and ideally the image to do anything,
but I can't promise that anything would come out of this.
Best would be a reproducer, or at least some operation that you can link
to the appearance of the corruption. Then we could take a more targeted
look at the respective code.
> As you can imagine, all this setup is in production, and for most of the
> VMs, I can not "play" with them. Moreover, we launched a campaign of
nightly
> stopping every VM, qemu-img check them one by one, then boot.
> So it might take some time before I find another corrupted image.
> (which I'll preciously store for debug)
>
> Other informations : We very rarely do snapshots, but I'm close to imagine
> that automated migrations of VMs could trigger similar behaviors on qcow2
> images.
To my knowledge, oVirt only uses external snapshots and creates them
with QMP. This should be perfectly safe because from the perspective of
the qcow2 image being snapshotted, it just means that it gets no new
write requests.
Migration is something more involved, and if you could relate the
problem to migration, that would certainly be something to look into. In
that case, it would be important to know more about the setup, e.g. is
it migration with shared or non-shared storage?
> Last point about the versions we use : yes that's old, yes we're planning to
> upgrade, but we don't know when.
That would be helpful, too. Nothing is more frustrating that debugging a
bug in an old version only to find that it's already fixed in the
current version (well, except maybe debugging and finding nothing).
Kevin
And, looking at your other email:
"- In the case of oVirt, we are here allowing tens of hosts to connect
to the same LUN. This LUN is then managed by a classical LVM setup, but
I see here no notion of concurrent access management. To date, I still
haven't understood how was managed these concurrent access to the same
LUN with no crash."
I'm hoping someone else on list can chime in with if this safe or not --
I'm not really familiar with how oVirt does things, but as long as the
rest of the stack is sound and nothing else is touching the qcow2 data
area, we should be OK, I'd hope.
(Though the last big qcow2 corruption I had to debug wound up being in
the storage stack and not in QEMU, so I have some prejudices here)
anyway, I'll try to help as best as I'm able, but no promises.
--js
8:51 a.m.
New subject: [Qemu-block] qcow2 images corruption
https://framadrop.org/r/Lvvr392QZo#/wOeYUUlHQAtkUw1E+x2YdqTqq21Pbic6OPBIH...
Le 14/02/2018 à 00:01, John Snow a écrit :
On 02/13/2018 04:41 AM, Kevin Wolf wrote:
> Am 07.02.2018 um 18:06 hat Nicolas Ecarnot geschrieben:
>> TL; DR : qcow2 images keep getting corrupted. Any workaround?
>
> Not without knowing the cause.
>
> The first thing to make sure is that the image isn't touched by a second
> process while QEMU is running a VM. The classic one is using 'qemu-img
> snapshot' on the image of a running VM, which is instant corruption (and
> newer QEMU versions have locking in place to prevent this), but we have
> seen more absurd cases of things outside QEMU tampering with the image
> when we were investigating previous corruption reports.
>
> This covers the majority of all reports, we haven't had a real
> corruption caused by a QEMU bug in ages.
>
>> After having found (https://access.redhat.com/solutions/1173623) the right
>> logical volume hosting the qcow2 image, I can run qemu-img check on it.
>> - On 80% of my VMs, I find no errors.
>> - On 15% of them, I find Leaked cluster errors that I can correct using
>> "qemu-img check -r all"
>> - On 5% of them, I find Leaked clusters errors and further fatal errors,
>> which can not be corrected with qemu-img.
>> In rare cases, qemu-img can correct them, but destroys large parts of the
>> image (becomes unusable), and on other cases it can not correct them at all.
>
> It would be good if you could make the 'qemu-img check' output available
> somewhere.
>
> It would be even better if we could have a look at the respective image.
> I seem to remember that John (CCed) had a few scripts to analyse
> corrupted qcow2 images, maybe we would be able to see something there.
>
Hi! I did write a pretty simplistic tool for trying to tell the shape of
a corruption at a glance. It seems to work pretty similarly to the other
tool you already found, but it won't hurt anything to run it:
https://github.com/jnsnow/qcheck
(Actually, that other tool looks like it has an awful lot of options.
I'll have to check it out.)
It can print a really upsetting amount of data (especially for very
corrupt images), but in the default case, the simple setting should do
the trick just fine.
You could always put the output from this tool in a pastebin too; it
might help me visualize the problem a bit more -- I find seeing the
exact offsets and locations of where all the various tables and things
to be pretty helpful.
You can also always use the "deluge" option and compress it if you want,
just don't let it print to your terminal:
jsnow@probe (dev) ~/s/qcheck> ./qcheck -xd
/home/bos/jsnow/src/qemu/bin/git/install_test_f26.qcow2 > deluge.log;
and ls -sh deluge.log
4.3M deluge.log
but it compresses down very well:
jsnow@probe (dev) ~/s/qcheck> 7z a -t7z -m0=ppmd deluge.ppmd.7z deluge.log
jsnow@probe (dev) ~/s/qcheck> ls -s deluge.ppmd.7z
316 deluge.ppmd.7z
So I suppose if you want to send along:
(1) The basic output without any flags, in a pastebin
(2) The zipped deluge output, just in case
and I will try my hand at guessing what went wrong.
(Also, maybe my tool will totally choke for your image, who knows. It
hasn't received an overwhelming amount of testing apart from when I go
to use it personally and inevitably wind up displeased with how it
handles certain situations, so ...)
>> What I read similar to my case is :
>> - usage of qcow2
>> - heavy disk I/O
>> - using the virtio-blk driver
>>
>> In the proxmox thread, they tend to say that using virtio-scsi is the
>> solution. Having asked this question to oVirt experts
>> (https://lists.ovirt.org/pipermail/users/2018-February/086753.html) but it's
>> not clear the driver is to blame.
>
> This seems very unlikely. The corruption you're seeing is in the qcow2
> metadata, not only in the guest data. If anything, virtio-scsi exercises
> more qcow2 code paths than virtio-blk, so any potential bug that affects
> virtio-blk should also affect virtio-scsi, but not the other way around.
>
>> I agree with the answer Yaniv Kaul gave to me, saying I have to properly
>> report the issue, so I'm longing to know which peculiar information I can
>> give you now.
>
> To be honest, debugging corruption after the fact is pretty hard. We'd
> need the 'qemu-img check' output and ideally the image to do anything,
> but I can't promise that anything would come out of this.
>
> Best would be a reproducer, or at least some operation that you can link
> to the appearance of the corruption. Then we could take a more targeted
> look at the respective code.
>
>> As you can imagine, all this setup is in production, and for most of the
>> VMs, I can not "play" with them. Moreover, we launched a campaign of
nightly
>> stopping every VM, qemu-img check them one by one, then boot.
>> So it might take some time before I find another corrupted image.
>> (which I'll preciously store for debug)
>>
>> Other informations : We very rarely do snapshots, but I'm close to imagine
>> that automated migrations of VMs could trigger similar behaviors on qcow2
>> images.
>
> To my knowledge, oVirt only uses external snapshots and creates them
> with QMP. This should be perfectly safe because from the perspective of
> the qcow2 image being snapshotted, it just means that it gets no new
> write requests.
>
> Migration is something more involved, and if you could relate the
> problem to migration, that would certainly be something to look into. In
> that case, it would be important to know more about the setup, e.g. is
> it migration with shared or non-shared storage?
>
>> Last point about the versions we use : yes that's old, yes we're planning
to
>> upgrade, but we don't know when.
>
> That would be helpful, too. Nothing is more frustrating that debugging a
> bug in an old version only to find that it's already fixed in the
> current version (well, except maybe debugging and finding nothing).
>
> Kevin
>
And, looking at your other email:
"- In the case of oVirt, we are here allowing tens of hosts to connect
to the same LUN. This LUN is then managed by a classical LVM setup, but
I see here no notion of concurrent access management. To date, I still
haven't understood how was managed these concurrent access to the same
LUN with no crash."
I'm hoping someone else on list can chime in with if this safe or not --
I'm not really familiar with how oVirt does things, but as long as the
rest of the stack is sound and nothing else is touching the qcow2 data
area, we should be OK, I'd hope.
(Though the last big qcow2 corruption I had to debug wound up being in
the storage stack and not in QEMU, so I have some prejudices here)
anyway, I'll try to help as best as I'm able, but no promises.
--js
--
Nicolas ECARNOT
1:07 p.m.
On Wed, Feb 7, 2018 at 7:09 PM Nicolas Ecarnot <nicolas(a)ecarnot.net> wrote:
Hello,
TL; DR : qcow2 images keep getting corrupted. Any workaround?
Long version:
This discussion has already been launched by me on the oVirt and on
qemu-block mailing list, under similar circumstances but I learned
further things since months and here are some informations :
- We are using 2 oVirt 3.6.7.5-1.el7.centos datacenters, using CentOS
7.{2,3} hosts
- Hosts :
- CentOS 7.2 1511 :
- Kernel = 3.10.0 327
- KVM : 2.3.0-31
- libvirt : 1.2.17
- vdsm : 4.17.32-1
- CentOS 7.3 1611 :
- Kernel 3.10.0 514
- KVM : 2.3.0-31
- libvirt 2.0.0-10
- vdsm : 4.17.32-1
- Our storage is 2 Equallogic SANs connected via iSCSI on a dedicated
network
In 3.6 and iSCSI storage you have the issue of lvmetad service, activating
oVirt volumes by default, and also activating guest lvs inside oVirt raw
volumes.
This can lead to data corruption if an lv was activated before it was
extended
on another host, and the lv size on the host does not reflect the actual lv
size.
We had many bugs related to this, check this for related bugs:
https://bugzilla.redhat.com/1374545
To avoid this issue, you need to
1. edit /etc/lvm/lvm.conf global/use_lvmetad to:
use_lvmetad = 0
2. disable and mask these services:
- lvm2-lvmetad.socket
- lvm2-lvmetad.service
Note that this will may cause warnings from systemd during boot, the
warnings
are harmless:
https://bugzilla.redhat.com/1462792
For extra safety and better performance, you should also setup lvm filter
on all hosts.
Check this for example how it is done in 4.x:
https://www.ovirt.org/blog/2017/12/lvm-configuration-the-easy-way/
Since you run 3.6 you will have to setup the filter manually in the same
way.
Nir
- Depends on weeks, but all in all, there are around 32 hosts, 8
storage
domains and for various reasons, very few VMs (less than 200).
- One peculiar point is that most of our VMs are provided an additional
dedicated network interface that is iSCSI-connected to some volumes of
our SAN - these volumes not being part of the oVirt setup. That could
lead to a lot of additional iSCSI traffic.
From times to times, a random VM appears paused by oVirt.
Digging into the oVirt engine logs, then into the host vdsm logs, it
appears that the host considers the qcow2 image as corrupted.
Along what I consider as a conservative behavior, vdsm stops any
interaction with this image and marks it as paused.
Any try to unpause it leads to the same conservative pause.
After having found (https://access.redhat.com/solutions/1173623) the
right logical volume hosting the qcow2 image, I can run qemu-img check
on it.
- On 80% of my VMs, I find no errors.
- On 15% of them, I find Leaked cluster errors that I can correct using
"qemu-img check -r all"
- On 5% of them, I find Leaked clusters errors and further fatal errors,
which can not be corrected with qemu-img.
In rare cases, qemu-img can correct them, but destroys large parts of
the image (becomes unusable), and on other cases it can not correct them
at all.
Months ago, I already sent a similar message but the error message was
about No space left on device
(https://www.mail-archive.com/qemu-block@gnu.org/msg00110.html).
This time, I don't have this message about space, but only corruption.
I kept reading and found a similar discussion in the Proxmox group :
https://lists.ovirt.org/pipermail/users/2018-February/086750.html
https://forum.proxmox.com/threads/qcow2-corruption-after-snapshot-or-heav...
What I read similar to my case is :
- usage of qcow2
- heavy disk I/O
- using the virtio-blk driver
In the proxmox thread, they tend to say that using virtio-scsi is the
solution. Having asked this question to oVirt experts
(https://lists.ovirt.org/pipermail/users/2018-February/086753.html) but
it's not clear the driver is to blame.
I agree with the answer Yaniv Kaul gave to me, saying I have to properly
report the issue, so I'm longing to know which peculiar information I
can give you now.
As you can imagine, all this setup is in production, and for most of the
VMs, I can not "play" with them. Moreover, we launched a campaign of
nightly stopping every VM, qemu-img check them one by one, then boot.
So it might take some time before I find another corrupted image.
(which I'll preciously store for debug)
Other informations : We very rarely do snapshots, but I'm close to
imagine that automated migrations of VMs could trigger similar behaviors
on qcow2 images.
Last point about the versions we use : yes that's old, yes we're
planning to upgrade, but we don't know when.
Regards,
--
Nicolas ECARNOT
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
2282
days inactive
2293
days old
8 comments
5 participants
participants (5)
-
John Snow -
Kevin Wolf -
Nicolas Ecarnot -
Nir Soffer -
Yaniv Kaul