2:55 a.m.
This is a multi-part message in MIME format.
--------------080303010305060104030604
Content-Type: text/plain; charset=utf-8; format=flowed
Content-Transfer-Encoding: 7bit
Hi folks,
I have a 3.5 hosted-engine setup, which was recently upgraded from 3.4.
It has five nodes, two of them set up for hosted-engine HA.
Initial problem:
One of the hosted-engine HVs had a score of 1800, owing to the
management bridge (ovirtmgmt) being absent.
I put ovirtmgmt bridge back in. The score went to 2400. Great!
After that, I could use hosted-engine --set-maintenance --mode=local to
force it to move to the other blade.
Can't migrate hosted-engine using the oVirt GUI though; I'm sure I've
done so before, is that still supposed to work in 3.5?
Second problem:
Having added the ovirtmgmt bridge, that HV, which was running VMs
before, now refuses to accept them.
An example from hosted-engine's engine.log, it refuses to put a VM on
these hosts:
2015-04-29 17:23:07,593 INFO
[org.ovirt.engine.core.bll.scheduling.SchedulingManager]
(ajp--127.0.0.1-8702-2) [4ca60585] Candidate host
bl09.networkvideo.com.au (4f26611a-9f44-4832-b9e3-1a06b1d513fc) was
filtered out by VAR__FILTERTYPE__INTERNAL *filter Network*
2015-04-29 17:23:07,595 INFO
[org.ovirt.engine.core.bll.scheduling.SchedulingManager]
(ajp--127.0.0.1-8702-2) [4ca60585] Candidate host
bl07.networkvideo.com.au (fc50be91-3e07-4447-a0d8-bffbda8a07c6) was
filtered out by VAR__FILTERTYPE__INTERNAL filter Network
I think it must relate to the configuration for either the ovirtmgmt
bridge, or the physical interface to which the bridge is connected.
I have seen, for example, the need for BOOTPROTO=none to be in the
ifcfg-file.
So, it seems that filter actually reads config files, and I suspect it's
looking for a certain directive and/or syntax. My guess, it's being
(too) fussy about syntax.
Has anyone else encountered this? I'd be glad to learn more about how
that filter works, if someone can point me in the right direction please.
The interface configs for the two scenarios are shown below.
1. eth0 without a bridge - like this, I can run VMs on the HV, but
hosted-engine won't go there (of course).
[root@bl09 network-scripts]# cat ifcfg-eth0
DEVICE=eth0
HWADDR=00:21:5a:48:4e:4a
ONBOOT=yes
IPADDR=10.0.14.9
NETMASK=255.255.255.0
GATEWAY=10.0.14.254
BOOTPROTO=none
MTU=1500
DEFROUTE=yes
NM_CONTROLLED=no
2. With the bridge in, as it is now, I can put hosted-engine on it, but
can't run other VMs on there.
[root@bl09 network-scripts]# cat ifcfg-eth0
DEVICE=eth0
HWADDR=00:21:5a:48:4e:4a
BOOTPROTO=none
ONBOOT=yes
BRIDGE=ovirtmgmt
MTU=1500
DEFROUTE=no
NM_CONTROLLED=no
[root@bl09 network-scripts]# cat ifcfg-ovirtmgmt
DEVICE=ovirtmgmt
ONBOOT=yes
TYPE=Bridge
DELAY=0
IPADDR=10.0.14.9
NETMASK=255.255.255.0
GATEWAY=10.0.14.254
BOOTPROTO=static
DEFROUTE=yes
NM_CONTROLLED=no
Any guidance appreciated.
--
Thanks,
Garry
--------------080303010305060104030604
Content-Type: text/html; charset=utf-8
Content-Transfer-Encoding: 8bit
<html>
<head>
<meta http-equiv="content-type" content="text/html;
charset=utf-8">
</head>
<body bgcolor="#FFFFFF" text="#000000">
Hi folks,<br>
<br>
I have a 3.5 hosted-engine setup, which was recently upgraded from
3.4. It has five nodes, two of them set up for hosted-engine HA.<br>
<br>
Initial problem:<br>
<br>
One of the hosted-engine HVs had a score of 1800, owing to the
management bridge (ovirtmgmt) being absent. <br>
I put ovirtmgmt bridge back in. The score went to 2400. Great!<br>
After that, I could use hosted-engine --set-maintenance --mode=local
to force it to move to the other blade.<br>
<br>
Can't migrate hosted-engine using the oVirt GUI though; I'm sure
I've done so before, is that still supposed to work in 3.5?<br>
<br>
Second problem:<br>
<br>
Having added the ovirtmgmt bridge, that HV, which was running VMs
before, now refuses to accept them.<br>
<br>
An example from hosted-engine's engine.log, it refuses to put a VM
on these hosts:<br>
<br>
<tt>2015-04-29 17:23:07,593 INFO
[org.ovirt.engine.core.bll.scheduling.SchedulingManager]
(ajp--127.0.0.1-8702-2) [4ca60585] Candidate host
bl09.networkvideo.com.au (4f26611a-9f44-4832-b9e3-1a06b1d513fc)
was filtered out by VAR__FILTERTYPE__INTERNAL <b>filter
Network</b></tt><tt><br>
</tt><tt>2015-04-29 17:23:07,595 INFO
[org.ovirt.engine.core.bll.scheduling.SchedulingManager]
(ajp--127.0.0.1-8702-2) [4ca60585] Candidate host
bl07.networkvideo.com.au (fc50be91-3e07-4447-a0d8-bffbda8a07c6)
was filtered out by VAR__FILTERTYPE__INTERNAL filter Network</tt><br>
<br>
I think it must relate to the configuration for either the ovirtmgmt
bridge, or the physical interface to which the bridge is connected.<br>
I have seen, for example, the need for BOOTPROTO=none to be in the
ifcfg-file.<br>
So, it seems that filter actually reads config files, and I suspect
it's looking for a certain directive and/or syntax. My guess, it's
being (too) fussy about syntax.<br>
<br>
Has anyone else encountered this? I'd be glad to learn more about
how that filter works, if someone can point me in the right
direction please.<br>
<br>
The interface configs for the two scenarios are shown below.<br>
<br>
1. eth0 without a bridge - like this, I can run VMs on the HV, but
hosted-engine won't go there (of course).<br>
<br>
<tt>[root@bl09 network-scripts]# cat ifcfg-eth0</tt><tt><br>
</tt><tt>DEVICE=eth0</tt><tt><br>
</tt><tt>HWADDR=00:21:5a:48:4e:4a</tt><tt><br>
</tt><tt>ONBOOT=yes</tt><tt><br>
</tt><tt>IPADDR=10.0.14.9</tt><tt><br>
</tt><tt>NETMASK=255.255.255.0</tt><tt><br>
</tt><tt>GATEWAY=10.0.14.254</tt><tt><br>
</tt><tt>BOOTPROTO=none</tt><tt><br>
</tt><tt>MTU=1500</tt><tt><br>
</tt><tt>DEFROUTE=yes</tt><tt><br>
</tt><tt>NM_CONTROLLED=no<br>
<br>
</tt>2. With the bridge in, as it is now, I can put hosted-engine on
it, but can't run other VMs on there.<br>
<br>
<tt>[root@bl09 network-scripts]# cat ifcfg-eth0</tt><tt><br>
</tt><tt>DEVICE=eth0</tt><tt><br>
</tt><tt>HWADDR=00:21:5a:48:4e:4a</tt><tt><br>
</tt><tt>BOOTPROTO=none</tt><tt><br>
</tt><tt>ONBOOT=yes</tt><tt><br>
</tt><tt>BRIDGE=ovirtmgmt</tt><tt><br>
</tt><tt>MTU=1500</tt><tt><br>
</tt><tt>DEFROUTE=no</tt><tt><br>
</tt><tt>NM_CONTROLLED=no</tt><tt><br>
</tt><tt>[root@bl09 network-scripts]# cat
ifcfg-ovirtmgmt</tt><tt><br>
</tt><tt>DEVICE=ovirtmgmt</tt><tt><br>
</tt><tt>ONBOOT=yes</tt><tt><br>
</tt><tt>TYPE=Bridge</tt><tt><br>
</tt><tt>DELAY=0</tt><tt><br>
</tt><tt>IPADDR=10.0.14.9</tt><tt><br>
</tt><tt>NETMASK=255.255.255.0</tt><tt><br>
</tt><tt>GATEWAY=10.0.14.254</tt><tt><br>
</tt><tt>BOOTPROTO=static</tt><tt><br>
</tt><tt>DEFROUTE=yes</tt><tt><br>
</tt><tt>NM_CONTROLLED=no</tt><br>
<br>
Any guidance appreciated.<br>
<br>
-- <br>
<div class="moz-signature">Thanks,<br>
<br>
Garry<br>
</div>
</body>
</html>
--------------080303010305060104030604--
2:12 a.m.
Il 29/04/2015 09:55, Garry Tiedemann ha scritto:
Hi folks,
I have a 3.5 hosted-engine setup, which was recently upgraded from 3.4. It has five
nodes, two of them set up for hosted-engine HA.
Initial problem:
One of the hosted-engine HVs had a score of 1800, owing to the management bridge
(ovirtmgmt) being absent.
I put ovirtmgmt bridge back in. The score went to 2400. Great!
After that, I could use hosted-engine --set-maintenance --mode=local to force it to move
to the other blade.
Can't migrate hosted-engine using the oVirt GUI though; I'm sure I've done so
before, is that still supposed to work in 3.5?
AFAIK yes, it should still be supported.
Second problem:
Having added the ovirtmgmt bridge, that HV, which was running VMs before, now refuses to
accept them.
An example from hosted-engine's engine.log, it refuses to put a VM on these hosts:
2015-04-29 17:23:07,593 INFO [org.ovirt.engine.core.bll.scheduling.SchedulingManager]
(ajp--127.0.0.1-8702-2) [4ca60585] Candidate host
bl09.networkvideo.com.au (4f26611a-9f44-4832-b9e3-1a06b1d513fc) was filtered out by
VAR__FILTERTYPE__INTERNAL *filter Network*
2015-04-29 17:23:07,595 INFO [org.ovirt.engine.core.bll.scheduling.SchedulingManager]
(ajp--127.0.0.1-8702-2) [4ca60585] Candidate host
bl07.networkvideo.com.au (fc50be91-3e07-4447-a0d8-bffbda8a07c6) was filtered out by
VAR__FILTERTYPE__INTERNAL filter Network
I think it must relate to the configuration for either the ovirtmgmt bridge, or the
physical interface to which the bridge is connected.
I have seen, for example, the need for BOOTPROTO=none to be in the ifcfg-file.
So, it seems that filter actually reads config files, and I suspect it's looking for
a certain directive and/or syntax. My guess, it's being (too)
fussy about syntax.
Has anyone else encountered this? I'd be glad to learn more about how that filter
works, if someone can point me in the right direction please.
The interface configs for the two scenarios are shown below.
1. eth0 without a bridge - like this, I can run VMs on the HV, but hosted-engine
won't go there (of course).
[root@bl09 network-scripts]# cat ifcfg-eth0
DEVICE=eth0
HWADDR=00:21:5a:48:4e:4a
ONBOOT=yes
IPADDR=10.0.14.9
NETMASK=255.255.255.0
GATEWAY=10.0.14.254
BOOTPROTO=none
MTU=1500
DEFROUTE=yes
NM_CONTROLLED=no
2. With the bridge in, as it is now, I can put hosted-engine on it, but can't run
other VMs on there.
[root@bl09 network-scripts]# cat ifcfg-eth0
DEVICE=eth0
HWADDR=00:21:5a:48:4e:4a
BOOTPROTO=none
ONBOOT=yes
BRIDGE=ovirtmgmt
MTU=1500
DEFROUTE=no
NM_CONTROLLED=no
[root@bl09 network-scripts]# cat ifcfg-ovirtmgmt
DEVICE=ovirtmgmt
ONBOOT=yes
TYPE=Bridge
DELAY=0
IPADDR=10.0.14.9
NETMASK=255.255.255.0
GATEWAY=10.0.14.254
BOOTPROTO=static
DEFROUTE=yes
NM_CONTROLLED=no
Any guidance appreciated.
--
Thanks,
Garry
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
--
Sandro Bonazzola
Better technology. Faster innovation. Powered by community collaboration.
See how it works at redhat.com
3277
days inactive
3278
days old
1 comments
2 participants
participants (2)
-
Garry Tiedemann -
Sandro Bonazzola