Sorry for delay in replying on this, I got pulled into some urgent meetings at the end of
the day.
Regarding the questions below,
Yes under the H/W tab my QLogic cards are listed. Looks like I have two different models
of cards, which could be, I think I acquired them off ebay and then got another one later
for redundancy.
WWNN and WWPNs are listed.
Miultipath -ll lists all my LUNs, multipathing is set to RR... not sure if that could be
problem as the SAN I am using (old EMC/DGC CX200) is active passive and I would assume it
would be MRU...
Hope this helps, still no LUNs showing up in my Engine.
Thanks again for your help.
Bill
-----Original Message-----
From: Daniel Helgenberger [mailto:daniel.helgenberger@m-box.de]
Sent: 11 September 2014 13:06
To: Bill Dossett
Subject: Re: [ovirt-users] FC QLogic question
On 11.09.2014 13:05, Bill Dossett wrote:
Hi Daniel,
I did a lsmod | grep qxl and it returned nothing... did you perhaps mean qla?
[root@ovirt141 ~]# lsmod | grep qla
qla2xxx 466573 56
I think that is the one
Indeed, sorry for that.
lsscsi does list all of the LUNs... so that's working!
Great!
But nothing in ovirt engine when I try to add a storage domain.
Please check back
in ovirt engine, with Hosts / Hardware info. You should see the adapter there, along with
WWN's ect.
I am not quite sure, but AFAIK the node uses dm-multipath by default (for iscsi
multipathing). So what does:
# multipath -ll
list?
Thanks again, I guess I will try and get a bit further with the installs I have...
Bill
-----Original Message-----
From: Daniel Helgenberger [mailto:daniel.helgenberger@m-box.de]
Sent: 11 September 2014 11:53
To: Bill Dossett
Subject: Re: [ovirt-users] FC QLogic question
On 11.09.2014 12:17, Bill Dossett wrote:
> Thanks for responding Daniel.
Never mind!
> I was wondering and thought the message may be irrelevant. But yes,
> it doesn't appear to be working. When I try to add a FC storage
> domain, no hosts are showing in the drop down box of hosts. I have
> loaded the latests ovirtnode (3.4.something...) on two hosts now and
> neither are working.
Lets first try to isolate your FC issure. So you are using the latest ovirt-node? EL6?
Keep in mind, the kernel is standard Linux and therefore should support Qlogic adapters
out of the box (IMHO they are the best supported HBAs in Linux).
Please try a:
# lsmod | grep qxl
to see whatever the qxl module is loaded. Keep in mind you can run into problems with
other conrollers in your host, though I only had this with LSI SAS / FC controllers so
far.
Further check on the FC switch if the N port is logged in and the zoning is correct.
Finally, check with
# lsscsi
if you can see the luns.
> Also having a lot of issues with configuring the network. I
> configure an interface I can ping it, but it shows as unconfigured...
> on one host I have added it to the manager and I see the interfaces
> anyway, but on the second host I configure the eth0, I can ping it,
> it added to the ovirt engine but it shows no NICs. Should I be using an earlier
version maybe?
>
> thanks again and best regards.
>
>
> *Bill Dossett*
> *Virtualisation Architect*
> *Pitney Bowes - Tech Central***
> 6 Hercules Way, 600 Leavesden Park
> Watford, WD25 7GS
> Phone(+44) (0)1923 279353 | VOIP: 54739353
> Mobile(+44) (0)7775 908612
> bill.dossett(a)pb.com <mailto:bill.dossett@pb.com>
www.pb.com
> <
http://www.pb.com/> *In Engineering?**Raise a ticket via Remedy
> Anywhere [HERE
> <
http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Inciden
> t
> /newIncident.aspx>]takes
> less than a minute*
>
> *ManageIQ User Guide available* [*HERE
> <
https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%2
> 0 v4.pdf>*] *Check out the ManageIQ Blog for recent enhancements and
> information [HERE]
> <
http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx>
> *
>
> On Sep 11, 2014, at 10:52 AM, Daniel Helgenberger
> <daniel.helgenberger(a)m-box.de <mailto:daniel.helgenberger@m-box.de>>
wrote:
>
>> Hello Bill,
>>
>> what are your problems acually? Is fibre channel not working (as expected)?
>>
>> The log snippet you provided is completly normal and the messages
>> can safely be ignored. This is also unrelated to oVirt but rather
>> CentOS (or the distro you are running) I suppose.
>>
>> Cheers!
>>
>> On 11.09.2014 10:51, Bill Dossett wrote:
>>> Hi,
>>>
>>> I seem to have run into a problem setting up ovirt with Fibre Channel
storage.
>>>
>>> I have a 2MBs SAN and qlogic cards in the nodes. I used this same
>>> setup with RHEV about 6 months ago and it just worked, storage was
>>> there no problems. Now booting with ovirtnode distro, I am seeing
>>>
>>> Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-0091:1:
>>> Firmware images can be retrieved from:
http://ldriver.qlogic.com/firmware/.
>>>
>>> Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx
>>>
>>> Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-00fb:1:
>>> QLogic QLE2460
>>> - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x.
>>>
>>> Sep 9 08:01:27 localhost kernel: qla2xxx [0000:0c:00.0]-00fc:1:
>>> ISP2432: PCIe (2.5GT/s x4) @ 0000:0c:00.0 hdma+ host#=1 fw=4.00.26 (2).
>>>
>>> Sep 9 08:01:27 localhost kernel: ata_piix 0000:00:1f.1: PCI INT A
>>> -> GSI 16 (level, low) -> IRQ 16
>>>
>>> I have googled the firmware error and it says some cards need a
>>> firmware flash and some don't. These are pretty standard HBAs so I
>>> would think they would be supported out of the box, but maybe not.
>>> Looking at trying to add the firmware looked kind of complex - if I
>>> need to do this, does anyone know of a nice and easy howto guide on
>>> this. I'm just getting started with ovirt and appreciate any help
>>>
>>>
>>> Thanks
>>>
>>> *Bill Dossett*
>>>
>>> *Virtualisation Architect*
>>>
>>> *Pitney Bowes - Tech Central***
>>>
>>> 6 Hercules Way, 600 Leavesden Park
>>>
>>> Watford, WD25 7GS
>>>
>>> Phone(+44) (0)1923 279353 | VOIP: 54739353
>>>
>>> Mobile(+44) (0)7775 908612
>>>
>>> bill.dossett(a)pb.com <mailto:bill.dossett@pb.com>
>>> <mailto:bill.dossett@pb.com>
>>>
>>>
www.pb.com <
http://www.pb.com> <
http://www.pb.com/>
>>>
>>> *In Engineering?**Raise a ticket via Remedy Anywhere [HERE
>>> <
http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incid
>>> ent/newIncident.aspx>]takes
>>>
>>> less than a minute*
>>>
>>> *ManageIQ User Guide available*[*HERE
>>> <
https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB
>>> %20v4.pdf>*]
>>>
>>> *Check out the ManageIQ Blog for recent enhancements and
>>> information [HERE]
>>> <
http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.asp
>>> x>*
>>>
>>>
>>> -------------------------------------------------------------------
>>> -------------
>>>
>> --
>> Daniel Helgenberger
>> m box bewegtbild GmbH
>>
>> P: +49/30/2408781-22
>> F: +49/30/2408781-10
>>
>> ACKERSTR. 19
>> D-10115 BERLIN
>>
>>
>>
www.m-box.de <
http://www.m-box.de> www.monkeymen.tv
>> <
http://www.monkeymen.tv>
>>
>> Geschäftsführer: Martin Retschitzegger / Michaela Göllner
>> Handeslregister: Amtsgericht Charlottenburg / HRB 112767
>>
>
> ---------------------------------------------------------------------
> -
> ----------
>
--
Daniel Helgenberger
m box bewegtbild GmbH
P: +49/30/2408781-22
F: +49/30/2408781-10
ACKERSTR. 19
D-10115 BERLIN
www.m-box.de www.monkeymen.tv
Geschäftsführer: Martin Retschitzegger / Michaela Göllner
Handeslregister: Amtsgericht Charlottenburg / HRB 112767
________________________________
--
Daniel Helgenberger
m box bewegtbild GmbH
P: +49/30/2408781-22
F: +49/30/2408781-10
ACKERSTR. 19
D-10115 BERLIN
www.m-box.de www.monkeymen.tv
Geschäftsführer: Martin Retschitzegger / Michaela Göllner
Handeslregister: Amtsgericht Charlottenburg / HRB 112767
________________________________