[Users] install a f18 host with ovirtmgmt vlan tagged
Hello, engine f18 3.2 stable. I try to install a host in a new DC where I only configured ovirtmgmt network as vlan tagged with vlan id 65 Install fails with this error in /var/log/ovirt-engine/host-deploy/ovirt-20130307154915-10.4.4.57.log ... 2013-03-07 15:49:15 ERROR otopi.context context._executeMethod:139 Failed to execute stage 'Setup validation': Interface em3.65 is VLAN interface However its configuration is unexpected .. On fedora18 host I have NetworkManger disabled and network enabled. At the moment the only adapter that starts on the system is em3 and its vlan counterpart em3.65, with these conf files: # cat ifcfg-em3 DEVICE=em3 HWADDR=00:1C:C4:AB:89:0F TYPE=Ethernet BOOTPROTO=none IPV6INIT=no UUID=0675d8c1-858e-4819-9c65-4ff5f63587b7 ONBOOT=yes NM_CONTROLLED=no # cat ifcfg-em3.65 DEVICE=em3.65 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no How should I configure the host at the beginning to have ovirtmgmt configured as VLAN tagged and host deploy with no complain? Thanks in advance, Gianluca
On Thu, Mar 7, 2013 at 3:58 PM, Gianluca Cecchi wrote:
# cat ifcfg-em3.65 DEVICE=em3.65 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no
How should I configure the host at the beginning to have ovirtmgmt configured as VLAN tagged and host deploy with no complain?
Thanks in advance, Gianluca
Tried also the alternative configuration with ifcfg-vlan65 instead of ifcfg-em3.65: # cat ifcfg-vlan65 DEVICE=vlan65 PHYSDEV=em3 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no But I get Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected. Possibly the involved code is on engine /usr/share/otopi/plugins/ovirt-host-deploy/vdsm/bridge.py ? In host-deploy log: 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:302 determine interface for 10.4.4.60 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:347 execute: ('/sbin/ip', 'route', 'get' , 'to', '10.4.4.60'), executable='None', cwd='None', env=None 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:364 execute-result: ('/sbin/ip', 'route' , 'get', 'to', '10.4.4.60'), rc=0 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:411 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stdout: 10.4.4.60 dev vlan65 src 10.4.4.57 cache 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:416 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stderr: 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:337 interface for 10.4. 4.60 is vlan65 2013-03-07 16:31:53 DEBUG otopi.context context._executeMethod:130 method exception Traceback (most recent call last): File "/tmp/ovirt-xz8p0a0BfX/pythonlib/otopi/context.py", line 120, in _executeMethod method['method']() File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 733, in _validation self._getVlanMasterDevice(name=interface) File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 393, in _getVlanMasterDevice interface=name, RuntimeError: Interface vlan65 is VLAN interface However its configuration is unexpected 2013-03-07 16:31:53 ERROR otopi.context context._executeMethod:139 Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected Do I have perhaps to name it ovirtmgmt from the beginning? Gianluca
On Thu, Mar 7, 2013 at 4:38 PM, Gianluca Cecchi <gianluca.cecchi@gmail.com> wrote:
On Thu, Mar 7, 2013 at 3:58 PM, Gianluca Cecchi wrote:
# cat ifcfg-em3.65 DEVICE=em3.65 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no
How should I configure the host at the beginning to have ovirtmgmt configured as VLAN tagged and host deploy with no complain?
Thanks in advance, Gianluca
Tried also the alternative configuration with ifcfg-vlan65 instead of ifcfg-em3.65:
# cat ifcfg-vlan65 DEVICE=vlan65 PHYSDEV=em3 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no
But I get Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected.
Possibly the involved code is on engine /usr/share/otopi/plugins/ovirt-host-deploy/vdsm/bridge.py ?
In host-deploy log:
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:302 determine interface for 10.4.4.60 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:347 execute: ('/sbin/ip', 'route', 'get' , 'to', '10.4.4.60'), executable='None', cwd='None', env=None 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:364 execute-result: ('/sbin/ip', 'route' , 'get', 'to', '10.4.4.60'), rc=0 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:411 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stdout: 10.4.4.60 dev vlan65 src 10.4.4.57 cache
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:416 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stderr:
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:337 interface for 10.4. 4.60 is vlan65 2013-03-07 16:31:53 DEBUG otopi.context context._executeMethod:130 method exception Traceback (most recent call last): File "/tmp/ovirt-xz8p0a0BfX/pythonlib/otopi/context.py", line 120, in _executeMethod method['method']() File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 733, in _validation self._getVlanMasterDevice(name=interface) File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 393, in _getVlanMasterDevice interface=name, RuntimeError: Interface vlan65 is VLAN interface However its configuration is unexpected 2013-03-07 16:31:53 ERROR otopi.context context._executeMethod:139 Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected
Do I have perhaps to name it ovirtmgmt from the beginning?
Gianluca
I'm all but a python expert..... but I think these blocks in /usr/share/otopi/plugins/ovirt-host-deploy/vdsm/bridge.py are the ones involved ... _RE_VLAN_ID = re.compile( flags=re.VERBOSE, pattern=r""" .* VID: ([0-9]+) .* """ ) _RE_VLAN_ID_VLANID = 1 _RE_VLAN_DEVICE = re.compile( flags=re.VERBOSE, pattern=r""" ^ Device: \s+ (\S+) \s* $ """ ) _RE_VLAN_DEVICE_DEVICE = 1 ... def _getVlanMasterDevice(self, name): interface = None vlanid = None try: with open( os.path.join( '/proc/net/vlan', name ), 'r' ) as f: for line in f: m = self._RE_VLAN_ID.match(line) if m is not None: vlanid = m.group(self._RE_VLAN_ID_VLANID) else: m = self._RE_VLAN_DEVICE.match(line) if m is not None: interface = m.group(self._RE_VLAN_DEVICE_DEVICE) if interface is None or vlanid is None: raise RuntimeError( ... In my case: # cat /proc/net/vlan/vlan65 vlan65 VID: 65 REORDER_HDR: 1 dev->priv_flags: 1 total frames received 1910 total bytes received 1319518 Broadcast/Multicast Rcvd 4 total frames transmitted 2232 total bytes transmitted 426338 Device: em3 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings:
On 3/7/2013 11:05 AM, Gianluca Cecchi wrote:
On Thu, Mar 7, 2013 at 4:38 PM, Gianluca Cecchi <gianluca.cecchi@gmail.com> wrote:
On Thu, Mar 7, 2013 at 3:58 PM, Gianluca Cecchi wrote:
# cat ifcfg-em3.65 DEVICE=em3.65 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no
How should I configure the host at the beginning to have ovirtmgmt configured as VLAN tagged and host deploy with no complain?
Thanks in advance, Gianluca Tried also the alternative configuration with ifcfg-vlan65 instead of ifcfg-em3.65:
# cat ifcfg-vlan65 DEVICE=vlan65 PHYSDEV=em3 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no
But I get Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected.
Possibly the involved code is on engine /usr/share/otopi/plugins/ovirt-host-deploy/vdsm/bridge.py ?
In host-deploy log:
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:302 determine interface for 10.4.4.60 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:347 execute: ('/sbin/ip', 'route', 'get' , 'to', '10.4.4.60'), executable='None', cwd='None', env=None 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:364 execute-result: ('/sbin/ip', 'route' , 'get', 'to', '10.4.4.60'), rc=0 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:411 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stdout: 10.4.4.60 dev vlan65 src 10.4.4.57 cache
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:416 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stderr:
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:337 interface for 10.4. 4.60 is vlan65 2013-03-07 16:31:53 DEBUG otopi.context context._executeMethod:130 method exception Traceback (most recent call last): File "/tmp/ovirt-xz8p0a0BfX/pythonlib/otopi/context.py", line 120, in _executeMethod method['method']() File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 733, in _validation self._getVlanMasterDevice(name=interface) File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 393, in _getVlanMasterDevice interface=name, RuntimeError: Interface vlan65 is VLAN interface However its configuration is unexpected 2013-03-07 16:31:53 ERROR otopi.context context._executeMethod:139 Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected
Do I have perhaps to name it ovirtmgmt from the beginning?
Gianluca I'm all but a python expert.....
but I think these blocks in /usr/share/otopi/plugins/ovirt-host-deploy/vdsm/bridge.py are the ones involved
Yes, I ran into this same problem with _RE_VLAN_ID not matching on whitespace instead of an actual space (there's a tab in the output). Alon submitted a patch last month but I don't remember if it has made it into a released rpm. Here's the relevant part: --- a/src/plugins/ovirt-host-deploy/vdsm/bridge.py +++ b/src/plugins/ovirt-host-deploy/vdsm/bridge.py @@ -128,8 +128,9 @@ class Plugin(plugin.PluginBase): _RE_VLAN_ID = re.compile( flags=re.VERBOSE, pattern=r""" + ^ .* - VID: ([0-9]+) + \sVID:\s(\d+)\s .* """ )
... _RE_VLAN_ID = re.compile( flags=re.VERBOSE, pattern=r""" .* VID: ([0-9]+) .* """ ) _RE_VLAN_ID_VLANID = 1
_RE_VLAN_DEVICE = re.compile( flags=re.VERBOSE, pattern=r""" ^ Device: \s+ (\S+) \s* $ """ ) _RE_VLAN_DEVICE_DEVICE = 1
...
def _getVlanMasterDevice(self, name): interface = None vlanid = None try: with open( os.path.join( '/proc/net/vlan', name ), 'r' ) as f: for line in f: m = self._RE_VLAN_ID.match(line) if m is not None: vlanid = m.group(self._RE_VLAN_ID_VLANID) else: m = self._RE_VLAN_DEVICE.match(line) if m is not None: interface = m.group(self._RE_VLAN_DEVICE_DEVICE)
if interface is None or vlanid is None: raise RuntimeError( ...
In my case: # cat /proc/net/vlan/vlan65 vlan65 VID: 65 REORDER_HDR: 1 dev->priv_flags: 1 total frames received 1910 total bytes received 1319518 Broadcast/Multicast Rcvd 4
total frames transmitted 2232 total bytes transmitted 426338 Device: em3 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Will be included in 1.0.1 ----- Original Message -----
From: "Jeff Bailey" <bailey@cs.kent.edu> To: users@ovirt.org Sent: Friday, March 8, 2013 1:29:28 AM Subject: Re: [Users] install a f18 host with ovirtmgmt vlan tagged
On 3/7/2013 11:05 AM, Gianluca Cecchi wrote:
On Thu, Mar 7, 2013 at 4:38 PM, Gianluca Cecchi <gianluca.cecchi@gmail.com> wrote:
On Thu, Mar 7, 2013 at 3:58 PM, Gianluca Cecchi wrote:
# cat ifcfg-em3.65 DEVICE=em3.65 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no
How should I configure the host at the beginning to have ovirtmgmt configured as VLAN tagged and host deploy with no complain?
Thanks in advance, Gianluca Tried also the alternative configuration with ifcfg-vlan65 instead of ifcfg-em3.65:
# cat ifcfg-vlan65 DEVICE=vlan65 PHYSDEV=em3 ONBOOT=yes BOOTPROTO=none VLAN=yes IPADDR=10.4.4.57 NETMASK=255.255.255.0 GATEWAY=10.4.4.250 NM_CONTROLLED=no
But I get Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected.
Possibly the involved code is on engine /usr/share/otopi/plugins/ovirt-host-deploy/vdsm/bridge.py ?
In host-deploy log:
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:302 determine interface for 10.4.4.60 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:347 execute: ('/sbin/ip', 'route', 'get' , 'to', '10.4.4.60'), executable='None', cwd='None', env=None 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.executeRaw:364 execute-result: ('/sbin/ip', 'route' , 'get', 'to', '10.4.4.60'), rc=0 2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:411 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stdout: 10.4.4.60 dev vlan65 src 10.4.4.57 cache
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge plugin.execute:416 execute-output: ('/sbin/ip', 'route', ' get', 'to', '10.4.4.60') stderr:
2013-03-07 16:31:53 DEBUG otopi.plugins.ovirt_host_deploy.vdsm.bridge bridge._getInterfaceForDestination:337 interface for 10.4. 4.60 is vlan65 2013-03-07 16:31:53 DEBUG otopi.context context._executeMethod:130 method exception Traceback (most recent call last): File "/tmp/ovirt-xz8p0a0BfX/pythonlib/otopi/context.py", line 120, in _executeMethod method['method']() File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 733, in _validation self._getVlanMasterDevice(name=interface) File "/tmp/ovirt-xz8p0a0BfX/otopi-plugins/ovirt-host-deploy/vdsm/bridge.py", line 393, in _getVlanMasterDevice interface=name, RuntimeError: Interface vlan65 is VLAN interface However its configuration is unexpected 2013-03-07 16:31:53 ERROR otopi.context context._executeMethod:139 Failed to execute stage 'Setup validation': Interface vlan65 is VLAN interface However its configuration is unexpected
Do I have perhaps to name it ovirtmgmt from the beginning?
Gianluca I'm all but a python expert.....
but I think these blocks in /usr/share/otopi/plugins/ovirt-host-deploy/vdsm/bridge.py are the ones involved
Yes, I ran into this same problem with _RE_VLAN_ID not matching on whitespace instead of an actual space (there's a tab in the output). Alon submitted a patch last month but I don't remember if it has made it into a released rpm. Here's the relevant part:
--- a/src/plugins/ovirt-host-deploy/vdsm/bridge.py +++ b/src/plugins/ovirt-host-deploy/vdsm/bridge.py @@ -128,8 +128,9 @@ class Plugin(plugin.PluginBase): _RE_VLAN_ID = re.compile( flags=re.VERBOSE, pattern=r""" + ^ .* - VID: ([0-9]+) + \sVID:\s(\d+)\s .* """ )
... _RE_VLAN_ID = re.compile( flags=re.VERBOSE, pattern=r""" .* VID: ([0-9]+) .* """ ) _RE_VLAN_ID_VLANID = 1
_RE_VLAN_DEVICE = re.compile( flags=re.VERBOSE, pattern=r""" ^ Device: \s+ (\S+) \s* $ """ ) _RE_VLAN_DEVICE_DEVICE = 1
...
def _getVlanMasterDevice(self, name): interface = None vlanid = None try: with open( os.path.join( '/proc/net/vlan', name ), 'r' ) as f: for line in f: m = self._RE_VLAN_ID.match(line) if m is not None: vlanid = m.group(self._RE_VLAN_ID_VLANID) else: m = self._RE_VLAN_DEVICE.match(line) if m is not None: interface = m.group(self._RE_VLAN_DEVICE_DEVICE)
if interface is None or vlanid is None: raise RuntimeError( ...
In my case: # cat /proc/net/vlan/vlan65 vlan65 VID: 65 REORDER_HDR: 1 dev->priv_flags: 1 total frames received 1910 total bytes received 1319518 Broadcast/Multicast Rcvd 4
total frames transmitted 2232 total bytes transmitted 426338 Device: em3 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
On Fri, Mar 8, 2013 at 7:40 AM, Joop van de Wege wrote:
Alon Bar-Lev schreef:
Will be included in 1.0.1 Of foo-bar.tar.gz :-)
where foo.bar is ovirt-host-deploy ... ;-) On my engine system: ovirt-host-deploy-1.0.0-1.fc18.noarch I confirm that the patch worked for me. Host installed and rebooted.... then unfortunately a cpu of the ost abandoned me so I can't at the moment verify other things on this host ;-( but from engine gui I see 2013-Mar-08, 06:49 Host f18ovn02 installed 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Termination. 2013-Mar-08, 06:49 Installing Host f18ovn02. Retrieving installation logs to: '/var/log/ovirt-engine/host-deploy/ovirt-20130308064947-10.4.4.57.log'. 2013-Mar-08, 06:49 Installing Host f18ovn02. Reboot scheduled. 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Pre-termination. 2013-Mar-08, 06:49 Installing Host f18ovn02. Reboot scheduled. 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Closing up. Installing Host f18ovn02. Reboot scheduled. Installing Host f18ovn02. Stage: Transaction commit. The only warning message in the gui is related to 2013-Mar-08, 06:49 Host f18ovn02 installation in progress . Cannot set tuned profile. BTW this host is an HP blade BL685c G1 with Opteron G2 Thanks, Gianluca
----- Original Message -----
From: "Gianluca Cecchi" <gianluca.cecchi@gmail.com> To: "Joop van de Wege" <jvdwege@xs4all.nl> Cc: "Alon Bar-Lev" <alonbl@redhat.com>, "users" <users@ovirt.org> Sent: Friday, March 8, 2013 9:07:42 AM Subject: Re: [Users] install a f18 host with ovirtmgmt vlan tagged
On Fri, Mar 8, 2013 at 7:40 AM, Joop van de Wege wrote:
Alon Bar-Lev schreef:
Will be included in 1.0.1 Of foo-bar.tar.gz :-)
where foo.bar is ovirt-host-deploy ... ;-) On my engine system: ovirt-host-deploy-1.0.0-1.fc18.noarch
I confirm that the patch worked for me. Host installed and rebooted....
then unfortunately a cpu of the ost abandoned me so I can't at the moment verify other things on this host ;-(
but from engine gui I see 2013-Mar-08, 06:49 Host f18ovn02 installed 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Termination. 2013-Mar-08, 06:49 Installing Host f18ovn02. Retrieving installation logs to: '/var/log/ovirt-engine/host-deploy/ovirt-20130308064947-10.4.4.57.log'. 2013-Mar-08, 06:49 Installing Host f18ovn02. Reboot scheduled. 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Pre-termination. 2013-Mar-08, 06:49 Installing Host f18ovn02. Reboot scheduled. 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Closing up. Installing Host f18ovn02. Reboot scheduled. Installing Host f18ovn02. Stage: Transaction commit.
The only warning message in the gui is related to 2013-Mar-08, 06:49 Host f18ovn02 installation in progress . Cannot set tuned profile.
BTW this host is an HP blade BL685c G1 with Opteron G2
This is probably fedora-18 issue of selinux and tuned[1], not sure why they don't solve it properly. Try to update selinux-policy and redeploy. [1] https://bugzilla.redhat.com/show_bug.cgi?id=882922
Thanks, Gianluca
----- Original Message -----
From: "Gianluca Cecchi" <gianluca.cecchi@gmail.com> To: "Joop van de Wege" <jvdwege@xs4all.nl> Cc: "Alon Bar-Lev" <alonbl@redhat.com>, "users" <users@ovirt.org> Sent: Friday, March 8, 2013 9:07:42 AM Subject: Re: [Users] install a f18 host with ovirtmgmt vlan tagged
On Fri, Mar 8, 2013 at 7:40 AM, Joop van de Wege wrote:
Alon Bar-Lev schreef:
Will be included in 1.0.1 Of foo-bar.tar.gz :-)
where foo.bar is ovirt-host-deploy ... ;-) On my engine system: ovirt-host-deploy-1.0.0-1.fc18.noarch
I confirm that the patch worked for me. Host installed and rebooted....
then unfortunately a cpu of the ost abandoned me so I can't at the moment verify other things on this host ;-(
but from engine gui I see 2013-Mar-08, 06:49 Host f18ovn02 installed 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Termination. 2013-Mar-08, 06:49 Installing Host f18ovn02. Retrieving installation logs to: '/var/log/ovirt-engine/host-deploy/ovirt-20130308064947-10.4.4.57.log'. 2013-Mar-08, 06:49 Installing Host f18ovn02. Reboot scheduled. 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Pre-termination. 2013-Mar-08, 06:49 Installing Host f18ovn02. Reboot scheduled. 2013-Mar-08, 06:49 Installing Host f18ovn02. Stage: Closing up. Installing Host f18ovn02. Reboot scheduled. Installing Host f18ovn02. Stage: Transaction commit.
The only warning message in the gui is related to 2013-Mar-08, 06:49 Host f18ovn02 installation in progress . Cannot set tuned profile.
BTW this host is an HP blade BL685c G1 with Opteron G2
Thanks, Gianluca
You can use the nightly build rpm of ovirt-host-deploy-1.0.1[1] [1] http://resources.ovirt.org/releases/nightly/rpm/Fedora/18/
participants (4)
-
Alon Bar-Lev -
Gianluca Cecchi -
Jeff Bailey -
Joop van de Wege