4:51 a.m.
I currently use KVM/virsh for my DNS. I would like it to ovirt, but I need DNS started for
the engine to work. So I need to start the DNS vm before the engine. Is that possible with
ovirt? I was thinking I could use the same mechanism as hosted engine, as that would
autostart.
In my current KVM setup I needed only to symlink /etc/libvirtd/qemu/dns.xml to
/etc/libvirtd/qemu/autostart/ to get it to run.
9:12 a.m.
New subject: Is it possible to auto-start VMs on single LocalStorage host without the engine?
It’s not recommended but you can put hard coded entries on /etc/hosts.
It used to work in the past (4 years ago), but I never relied on this recently.
On 25 Nov 2022, at 07:51, ernest.beinrohr(a)axonpro.sk wrote:
I currently use KVM/virsh for my DNS. I would like it to ovirt, but I need DNS started
for the engine to work. So I need to start the DNS vm before the engine. Is that possible
with ovirt? I was thinking I could use the same mechanism as hosted engine, as that would
autostart.
In my current KVM setup I needed only to symlink /etc/libvirtd/qemu/dns.xml to
/etc/libvirtd/qemu/autostart/ to get it to run.
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/JPREYFWDOYK...
11:08 p.m.
New subject: Is it possible to auto-start VMs on single LocalStorage host without the engine?
What the engine does is to read all the data from the DB, create a configuration for that
VM and power it up.
Once it's up, use virsh to dump the xml config and use that in a systemd script to
create the VM and run it (virsh define conf.xml; virsh start VM).
Best Regards,Strahil Nikolov
On Fri, Nov 25, 2022 at 17:13, Vinícius Ferrão via Users<users(a)ovirt.org> wrote:
It’s not recommended but you can put hard coded entries on /etc/hosts.
It used to work in the past (4 years ago), but I never relied on this recently.
On 25 Nov 2022, at 07:51, ernest.beinrohr(a)axonpro.sk wrote:
I currently use KVM/virsh for my DNS. I would like it to ovirt, but I need DNS started
for the engine to work. So I need to start the DNS vm before the engine. Is that possible
with ovirt? I was thinking I could use the same mechanism as hosted engine, as that would
autostart.
In my current KVM setup I needed only to symlink /etc/libvirtd/qemu/dns.xml to
/etc/libvirtd/qemu/autostart/ to get it to run.
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/JPREYFWDOYK...
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/YEBPMSLQZVK...
523
days inactive
527
days old
2 comments
3 participants
participants (3)
-
ernest.beinrohr＠axonpro.sk -
Strahil Nikolov -
Vinícius Ferrão