[Users] Windows 7 networking problem
Hi, Ive installed Windows 7 guest and when I connect Virtio NIC it only gets IP address from DHCP, but I can not communicate, even not ping to network. I used red-hat packaged virtio driver in version 1.6.3 and than 0.1-52 from linux-kvm.com, but the result is the same. (I restarted Windows several times). My Ubuntu guest works great. What do I wrong? Thank you ;-)
Hi Jabuk, we had the same issue with our windows server VMs under oVirt3.0, by switching bonding mode of the HVs from trunk to LACP we did get this solved. Root cause unknown.We have 0.1-52 driver installed on w2k8/12. Not sure if you are running in the same issue here?! Otherwise you should take a look at the hypervisor network bridge which has been assigned to this VM, and check if the tagging is correct and network traffic is going through. Cheers, Sven. Sven Knohsalla | System Administration | Netbiscuits Office +49 631 68036 433 | Fax +49 631 68036 111 |E-Mail s.knohsalla@netbiscuits.com | Skype: netbiscuits.admin Netbiscuits GmbH | Europaallee 10 | 67657 | GERMANY -----Ursprüngliche Nachricht----- Von: users-bounces@ovirt.org [mailto:users-bounces@ovirt.org] Im Auftrag von Jakub Bittner Gesendet: Donnerstag, 23. Mai 2013 19:30 An: users@ovirt.org Betreff: [Users] Windows 7 networking problem Hi, Ive installed Windows 7 guest and when I connect Virtio NIC it only gets IP address from DHCP, but I can not communicate, even not ping to network. I used red-hat packaged virtio driver in version 1.6.3 and than 0.1-52 from linux-kvm.com, but the result is the same. (I restarted Windows several times). My Ubuntu guest works great. What do I wrong? Thank you ;-) _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Dne 23.5.2013 20:03, Sven Knohsalla napsal(a):
Hi Jabuk,
we had the same issue with our windows server VMs under oVirt3.0, by switching bonding mode of the HVs from trunk to LACP we did get this solved. Root cause unknown.We have 0.1-52 driver installed on w2k8/12.
Not sure if you are running in the same issue here?!
Otherwise you should take a look at the hypervisor network bridge which has been assigned to this VM, and check if the tagging is correct and network traffic is going through.
Cheers, Sven.
Sven Knohsalla | System Administration | Netbiscuits
Office +49 631 68036 433 | Fax +49 631 68036 111 |E-Mail s.knohsalla@netbiscuits.com | Skype: netbiscuits.admin Netbiscuits GmbH | Europaallee 10 | 67657 | GERMANY
-----Ursprüngliche Nachricht----- Von: users-bounces@ovirt.org [mailto:users-bounces@ovirt.org] Im Auftrag von Jakub Bittner Gesendet: Donnerstag, 23. Mai 2013 19:30 An: users@ovirt.org Betreff: [Users] Windows 7 networking problem
Hi,
Ive installed Windows 7 guest and when I connect Virtio NIC it only gets IP address from DHCP, but I can not communicate, even not ping to network. I used red-hat packaged virtio driver in version 1.6.3 and than 0.1-52 from linux-kvm.com, but the result is the same. (I restarted Windows several times). My Ubuntu guest works great.
What do I wrong?
Thank you ;-) _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
I changed mode to mode1 Active-backup and it works. I will try 802.3ad later.. Thank you
-----Original message-----
From:Jakub Bittner <j.bittner@nbu.cz> Sent: Thursday 23rd May 2013 19:30 To: users@ovirt.org Subject: [Users] Windows 7 networking problem
Hi,
Ive installed Windows 7 guest and when I connect Virtio NIC it only gets IP address from DHCP, but I can not communicate, even not ping to network. I used red-hat packaged virtio driver in version 1.6.3 and than 0.1-52 from linux-kvm.com, but the result is the same. (I restarted Windows several times). My Ubuntu guest works great.
Hi, In another thread you wrote that you want to migrate from oVirt to RHEV. Do you have both environments running in the same network? RHEV and oVirt uses the same MAC range (if not changed with engine-config), so you should check if you have duplicate MAC addresses which causes the issues with your windows vm... Regards, René
What do I wrong?
Thank you ;-) _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Dne 23.5.2013 20:23, René Koch napsal(a):
-----Original message-----
From:Jakub Bittner <j.bittner@nbu.cz> Sent: Thursday 23rd May 2013 19:30 To: users@ovirt.org Subject: [Users] Windows 7 networking problem
Hi,
Ive installed Windows 7 guest and when I connect Virtio NIC it only gets IP address from DHCP, but I can not communicate, even not ping to network. I used red-hat packaged virtio driver in version 1.6.3 and than 0.1-52 from linux-kvm.com, but the result is the same. (I restarted Windows several times). My Ubuntu guest works great. Hi,
In another thread you wrote that you want to migrate from oVirt to RHEV. Do you have both environments running in the same network?
RHEV and oVirt uses the same MAC range (if not changed with engine-config), so you should check if you have duplicate MAC addresses which causes the issues with your windows vm...
Regards, René
What do I wrong?
Thank you ;-) _______________________________________________ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
We plan migration from Ovirt to RHEV in future. I asked because now I am migrating libvirt based to Ovirt and after we buy RHEV I want to just switch as easy as possible to RHEV (Export/Import). Thats why I ask. I do not want to migrate multiple times :-)
participants (3)
-
Jakub Bittner -
René Koch -
Sven Knohsalla