[Users] iSCSI discovery not showing all LUNs - oVirt 3.1

[Itamar Heim]

On 07/05/2012 06:08 PM, Trey Dockendorf wrote:
> I have a Promise M300i iSCSI with 2 LUNs.  A 2TB LUN with ID
> 2260-0001-557c-af0a and a 4TB LUN with ID 22d9-0001-553e-4d6a.
>
> What's strange, is the very first time I ran discovery I saw both
> LUNs.  I checked the 2TB LUN and storage failed to add, I don't have
> logs at this time, but I went back to repeat the process and now only
> 1 LUN shows in the GUI (see attached image).  Also the size it reports
> is way off.
>
> Looking at VDSM logs, I get this output when doing the login to a target
>
> {'devList':
>    [
>      {'vendorID': 'Promise',
>       'capacity': '2188028149760',
>       'fwrev': '0227',
>       'partitioned': False,
>       'vgUUID': 'AZ1iMt-gzBD-2uug-xTih-1z0b-PqPy-xSP0A4',
>       'pathlist': [
> 	{
> 	  'initiatorname': 'default',
> 	  'connection': '192.168.203.100',
> 	  'iqn': 'iqn.1994-12.com.promise.xxx',
> 	  'portal': '1',
> 	  'password': '******',
> 	  'port': '3260'
> 	}
>        ],
>        'logicalblocksize': '512',
>        'pathstatus': [
> 	{
> 	  'physdev': 'sde',
> 	  'type': 'iSCSI',
> 	  'state': 'active',
> 	  'lun': '0'
> 	}
>        ],
>        'devtype': 'iSCSI',
>        'physicalblocksize': '512',
>        'pvUUID': 'v2N3ok-wrki-OQQn-1XFL-w69n-8wAF-rmCFWt',
>        'serial': 'SPromise_VTrak_M300i_000000000000000000000000F08989F89FFF6C42',
>        'GUID': '222600001557caf0a',
>        'productID': 'VTrak M300i'
>      },
>      {
>        'vendorID': 'Promise',
>        'capacity': '20246190096384',
>        'fwrev': '0227',
>        'partitioned': False,
>        'vgUUID': '',
>        'pathlist': [
> 	{
> 	  'initiatorname': 'default',
> 	  'connection': '192.168.203.100',
> 	  'iqn': 'iqn.1994-12.com.promise.xxx',
> 	  'portal': '1',
> 	  'password': '******',
> 	  'port': '3260'
> 	}
>        ],
>        'logicalblocksize': '2048',
>        'pathstatus': [
> 	{
> 	  'physdev': 'sdf',
> 	  'type': 'iSCSI',
> 	  'state': 'active',
> 	  'lun': '1'
> 	}
>        ],
>        'devtype': 'iSCSI',
>        'physicalblocksize': '2048',
>        'pvUUID': '',
>        'serial': 'SPromise_VTrak_M300i_000000000000000000000000DA3FF8D8099662D7',
>        'GUID': '222d90001553e4d6a',
>        'productID': 'VTrak M300i'
>      }
>    ]
> }
>
> In that output both LUNs are seen.  I couldn't tell from the code what
> format the "capacity" is in, but now the interface shows only the LUN
> with the "4d6a" GUID as being 18TB.
>
> I've attached the VDSM Logs from the point of selecting my datacenter
> to after clicking "Login".  Any suggestions?
>
> node - vdsm-4.10.0-2.el6.x86_64
>
> Thanks
> - Trey
>
>
>
> _______________________________________________
> Users mailing list
> Users at ovirt.org
> http://lists.ovirt.org/mailman/listinfo/users
>

the LUN you don't see is 'dirty' and vdsm filters it.
there are some patches for showing all LUNs and just graying them out at 
ui level (but these are post ovirt 3.1.
dd with zeros the start of your LUN should bring it back