[Users] Unable to login into console Spice VNC anyone?

Brent Bolin brent.bolin at gmail.com
Wed Jul 25 15:52:09 UTC 2012


Thanks David for your reply -

I have completely flushed all iptables rules 'iptables --flush" -

iptables -L -v -n
Chain INPUT (policy ACCEPT 1775K packets, 627M bytes)
 pkts bytes target     prot opt in     out     source
destination

Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source
destination

Chain OUTPUT (policy ACCEPT 1754K packets, 589M bytes)
 pkts bytes target     prot opt in     out     source
destination


The base host is Fedora 16 running with desktop

First installed vdsm and then ovirt-engine

Single network bridge installed, but there is another 1GB nic that isn't
being used -

eth0      Link encap:Ethernet  HWaddr 00:1B:21:7D:ED:4A
          inet6 addr: fe80::21b:21ff:fe7d:ed4a/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:99656 errors:0 dropped:0 overruns:0 frame:0
          TX packets:51508 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:63007897 (60.0 MiB)  TX bytes:18148736 (17.3 MiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:1814674 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1814674 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:646274067 (616.3 MiB)  TX bytes:646274067 (616.3 MiB)

ovirtmgmt Link encap:Ethernet  HWaddr 00:1B:21:7D:ED:4A
          inet addr:192.168.0.118  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::21b:21ff:fe7d:ed4a/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:70706 errors:0 dropped:0 overruns:0 frame:0
          TX packets:48717 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:52195637 (49.7 MiB)  TX bytes:14942359 (14.2 MiB)

vnet0     Link encap:Ethernet  HWaddr FE:1A:4A:A8:00:00
          inet6 addr: fe80::fc1a:4aff:fea8:0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:14 errors:0 dropped:0 overruns:1 carrier:0
          collisions:0 txqueuelen:500
          RX bytes:1299 (1.2 KiB)  TX bytes:2760 (2.6 KiB)

After ovirt engine is installed logged into the interface and configured
the host using 127.0.0.1 .  Host reboots.  Host shows up in the admin
interface only complaining about power management that isn't configured.


Here<https://picasaweb.google.com/lh/photo/3vclaT_6d3uy2QODU6xp_zyLvDWH8k_pPWnP_LVb4fM?feat=directlink>is
a screen shot of the web interface

The only configuration settings I've changed are in the qemu.conf to either
tls=0 or tls=1

spice-gtk-0.11-4.fc16.x86_64
spice-client-0.10.1-1.fc16.x86_64
spice-glib-0.11-4.fc16.x86_64
spice-gtk3-0.11-4.fc16.x86_64
spice-xpi-2.7-3.fc16.x86_64
spice-gtk-tools-0.11-4.fc16.x86_64
spice-server-0.10.1-1.fc16.x86_64

The link in the admin interface shows available(using FF).  When I click it
opens a spicec:0 dialog and just closes

If I try to open from a shell I get things like this -

Brief window open and then error -

spicec -h 127.0.0.1 -p 5900
Warning: connect error 5 - need secured connection







On Wed, Jul 25, 2012 at 10:04 AM, David Jaša <djasa at redhat.com> wrote:
> Hi Brent,
>
> first guess: have a look if your iptables setup allow connection to the
> qemu processes. RHEV 3.0 documentation (publicly accesible) says that a
> host needs these ports open:
>         port 22 for SSH,
>         ports 5634 to 6166 for guest console connections,
>         port 16514 for libvirt virtual machine migration traffic,
>         ports 49152 to 49216 for VDSM virtual machine migration traffic,
>         and
>         port 54321 for the Red Hat Enterprise Virtualization Manager.
>
> If you have ovirt-engine running onu the same machine as vdsm, most of
> the ports don't need to be accessible from outside but "guest console"
> ports do.
>
> If it isn't iptables, please share at least:
> * what your actual topology is (engine on the physical host?)
> * if you use some custom tls settings such as tls switched off
> * what spice client & xpi versions are you using
> * how exactly the client failed (showed error window? with what error?
>   just didn't launch?)
>
> In your email, you didn't write any debugging hints apart from the setup
> being single-host one...
>
> David
>
>
> Brent Bolin píše v St 25. 07. 2012 v 09:00 -0500:
>> About 6 months ago I asked on this list if it was possible to install
>> ovirt on a single host.  Thread got long and winded and lost interest.
>>
>> Started looking at the project again about two days ago.  What I
>> really didn't understand was using a base Fedora install.  Installing
>> vdsm and then installing ovirt engine.
>>
>> So everything is up.  Created data center, storage, cluster, host and
>> virtual machine.
>>
>> But I can't get there from here.  I can't get console running to
>> configure the booted install.
>>
>> I've tried VNC, Spice, Firefox with spice-xpi plugin.
>>
>> Tried tweaking, turning, touching, swearing @ /etc/libvirt/qemu.conf
>> settings.  tls settings.  Not even sure if this is the right place to
>> be checking.
>>
>> This is a show stopper.
>>
>> LSB Version:    :core-4.0-amd64:core-4.0-noarch
>> Distributor ID: Fedora
>> Description:    Fedora release 16 (Verne)
>> Release:        16
>> Codename:       Verne
>>
>> [root at ovirt # rpm -qa|grep ovirt-engine
>> ovirt-engine-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-log-collector-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-iso-uploader-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-backend-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-notification-service-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-jboss-deps-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-tools-common-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-dbscripts-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-setup-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-jbossas-1.2-2.fc16.x86_64
>> ovirt-engine-userportal-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-restapi-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-genericapi-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-config-3.0.0_0001-1.6.fc16.x86_64
>> ovirt-engine-webadmin-portal-3.0.0_0001-1.6.fc16.x86_64
>>
>> Any input would be appreciated
>> _______________________________________________
>> Users mailing list
>> Users at ovirt.org
>> http://lists.ovirt.org/mailman/listinfo/users
>
> --
>
> David Jaša, RHCE
>
> SPICE QE based in Brno
> GPG Key:     22C33E24
> Fingerprint: 513A 060B D1B4 2A72 7F0D 0278 B125 CD00 22C3 3E24
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20120725/32dba271/attachment-0001.html>


More information about the Users mailing list