[Users] Ovirt allinone exists during setup

[Ohad Basan]

I am not sure that there actually a network configuration issue.
"ip addr" shows that the ovirtmgmt bridge functions correctly (it gets an
ip.)
yet, I don't know if it's related or not - creating the host from the
engine itself (or during the setup process) fails with an error.


On Mon, Jun 18, 2012 at 1:57 PM, Ofer Schreiber <oschreib at redhat.com> wrote:

>
>
> ----- Original Message -----
> >
> > The people who encountered a similar issue have just suggeted to take
> > down both network interface and then start one of them (since they
> > start one another). restarting the vdsm is smooth
> > and this is what I did - yet at the engine when creating a host an
> > error while creating the host appears
> > perhaps the engine log will help
> > googling suggests that there is mismatch of software packages and is
> > referring to mysql so I'm not sure it's related.
> >
>
> I'm not sure I completely understood what you're saying.
>
> The network interface issue has nothing to do with the engine.
> The engine just needs a bridge named ovirtmgmt on the host (localhost in
> your case).
>
> >
> >
> >
> > On Mon, Jun 18, 2012 at 1:26 PM, Ofer Schreiber < oschreib at redhat.com
> > > wrote:
> >
> >
> >
> >
> >
> > ----- Original Message -----
> > >
> > > hey
> > > thanks for the answer.
> > >
> > > 1. where exactly do i see the state of the host
> > > 2. I did as you instructed. the setup fails exactly at the same
> > > step
> > > (I changed the timeout to 600, shut down networkmanager and
> > > connected via dhcp over ethernet.
> >
> > Weird, which line did you changed? does the log still saying the host
> > status is "installing"?
> >
> >
> > > 2. I manually configured as following
> > >
> > > /etc/sysconfig/network-scripts/ifcfg-ovirtmgmt
> > > DEVICE=ovirtmgmt
> > > TYPE=Bridge
> > > ONBOOT=yes
> > > DELAY=0
> > > BOOTPROTO=dhcp
> > > NM_CONTROLLED="no
> > >
> > > and added
> > > BRIDGE=ovirtmgmt
> > > to the ifcfg-eth0
> > >
> > >
> > > restarting the network service fails with a status error
> > > RTNETLINK answers: File exists.
> >
> > Again, sounds like something is bad with your network configuration.
> > There are multiple results in google for that issue...
> >
> >
> >
> > >
> > > thanks
> > >
> > >
> > >
> > > On Mon, Jun 18, 2012 at 11:21 AM, Ofer Schreiber <
> > > oschreib at redhat.com > wrote:
> > >
> > >
> > >
> > > >
> > > > the bootstrap logs are also available
> > > > here they are.
> > > > thanks.
> > >
> > > 1. If you log into the GUI, in which state is the host?
> > >
> > > 2. From the engine.log, I can see that the host installation went
> > > fine, and it seems that the host is in "Non-Operetional state).
> > > - I can see clearly in the log :"Host local_host is set to
> > > Non-Operational, it is missing the following networks: ovirtmgmt"
> > >
> > > 3. in the vds_bootstrap.498578.log you can see "ERROR
> > > _getBridgeParams: failed to read params of file
> > > /etc/sysconfig/network-scripts/ifcfg-wlan0." - it seems that
> > > something is wrong with your networking configuration
> > >
> > > 4. Probably the timeout during all-in-one installation (150
> > > seconds)
> > > is too low for you.
> > >
> > >
> > > Two options for you:
> > > 1. Clean everything (using engine-cleanup), fix you networking
> > > settings (disable NetworkManager, use non wireless conntection) and
> > > rerun engine-setup (with higher timeout in
> > > /usr/share/ovirt-engine/scripts/plugins/all_in_one_100.py)
> > >
> > > 2. Just create the ovirtmgmt network bridge by your self, and
> > > restart
> > > vdsm.
> > >
> > >
> > >
> > > >
> > > >
> > > >
> > > > On Mon, Jun 18, 2012 at 10:40 AM, Ofer Schreiber <
> > > > oschreib at redhat.com > wrote:
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > ----- Original Message -----
> > > > >
> > > > > The log is attached.
> > > > >
> > > > > thanks
> > > >
> > > > I'm missing the vds_bootstrap* logs. are they available?
> > > > if not, if you log into the GUI, in which state the host is
> > > > currently
> > > > at?
> > > >
> > > > (/var/log/ovirt-enging/*log might help as well)
> > > >
> > > >
> > > >
> > > > >
> > > > >
> > > > >
> > > > > On Mon, Jun 18, 2012 at 10:26 AM, Ofer Schreiber <
> > > > > oschreib at redhat.com > wrote:
> > > > >
> > > > >
> > > > > It seems that the host is currently in "installing" state.
> > > > > Could you please take a look (or attach us) the vdsm
> > > > > installation
> > > > > logs under /tmp?
> > > > > (/tmp/vds_*)
> > > > >
> > > > >
> > > > >
> > > > > ----- Original Message -----
> > > > > >
> > > > > > Hello.
> > > > > >
> > > > > > I'm experiencing a problem during installation of the ovirt
> > > > > > engine
> > > > > > including the all-in-one plugin
> > > > > > The setup exists during the stage "Adding local host" - it
> > > > > > quits
> > > > > > due
> > > > > > to a "time out while waiting for the host to start"
> > > > > > I've attached some info (including the setup's log) and will
> > > > > > gladly
> > > > > > provide more information if necessary.
> > > > > >
> > > > > > Many thanks,
> > > > > >
> > > > > > Ohad
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20120618/940af3fc/attachment-0001.html>