[Users] Creating Logical Network issue - API

[Moti Asayag]

----- Original Message -----
> From: "Tejesh M" <tejeshmk at gmail.com>
> To: "Moti Asayag" <masayag at redhat.com>
> Cc: "users at oVirt.org" <users at ovirt.org>
> Sent: Monday, February 24, 2014 11:59:42 AM
> Subject: Re: [Users] Creating Logical Network issue - API
> 
> While setting Logical Network, it fails with below error:
> code  : 400
> reason: Bad Request
> detail: Previous network name is required.

See an example in the following post:

https://motiasayag.wordpress.com/2014/02/24/network-configuration-using-ovirt-engine-java-sdk/

> 
> Code:
>           String nw_name="ApiNetWork";
>           org.ovirt.engine.sdk.decorators.Host hst =
> api.getHosts().get("rhevhost");
> 
> hst.getHostNics().get("eth1").setNetwork(api.getNetworks().get(nw_name));
>           //hst.getHostNics().get("eth1").setCheckConnectivity(true);
>           //hst.getHostNics().get("eth1").setOverrideConfiguration(true);
>           hst.getHostNics().get("eth1").update();
> 
> 
> 
> On Mon, Feb 24, 2014 at 2:30 PM, Tejesh M <tejeshmk at gmail.com> wrote:
> 
> > Can you tel me how do i assign Logical Network(s) to one of the Physical
> > Nic on the Host.
> >
> >
> > On Fri, Feb 21, 2014 at 1:37 PM, Moti Asayag <masayag at redhat.com> wrote:
> >
> >> h
> >>
> >> ----- Original Message -----
> >> > From: "Tejesh M" <tejeshmk at gmail.com>
> >> > To: "users at oVirt.org" <users at ovirt.org>
> >> > Sent: Thursday, February 20, 2014 11:48:56 AM
> >> > Subject: [Users] Creating Logical Network issue - API
> >> >
> >> > Hi ,
> >> >
> >> > I'm trying to create Logical Network and assign it to cluster & want to
> >> bond
> >> > this to one of the Network Interface on Host. so that i can isolate my
> >> VM
> >> > from other networks.
> >> >
> >> > The issue is even if i set Cluster while creating Logical Network, it
> >> is not
> >> > setting the cluster. In Web Admin it is in unset state.
> >> >
> >> > Also, let me know how do i bind this Logical network on Host Interface.
> >> >
> >> > Java code:
> >> >
> >> > Network nw1=new Network();
> >> > VLAN vlan = new VLAN();
> >> > vlan.setId(2000);
> >> > nw1.setVlan(vlan);
> >> > IP ip = new IP();
> >> > ip.setAddress("192.168.1.151");
> >> > ip.setGateway("192.168.1.1");
> >> > ip.setNetmask("255.255.255.0");
> >>
> >> Note that the stated IP above will not be used to set the address on the
> >> host itself.
> >> In order to do so you should use either the 'setup networks' api on
> >> host's nics level.
> >> (Alternately, you can send POST request to /hosts/{host:id}/nics which
> >> utilize the
> >> former api (it is a bit simpler than using the setup networks api).
> >>
> >> Should look like:
> >>     Host host = api.getHosts().get("host_name");
> >>     Action action = new Action();
> >>     action.setCheckConnectivity(true); //required for rollback in case of
> >> configuration failure
> >>     action.setHostNics(...); // should contain the target configuration
> >>     host.getHostNics().setupnetworks(action);
> >>
> >> where the action should contain the entire desired network configuration.
> >>
> >> You can find various python-sdk example for setup networks on my blog [1]
> >> I'll post few examples using the java sdk earlier next week.
> >>
> >> [1] https://motiasayag.wordpress.com/
> >>
> >> > nw1.setIp(ip);
> >> > nw1.setName("apiNetwork");
> >> >
> >> > nw1.setDataCenter(api.getDataCenters().get("testDC"));
> >> > nw1.setCluster(api.getClusters().get("testCluster"));
> >> >
> >> > org.ovirt.engine.sdk.decorators.Network nw2 =
> >> api.getNetworks().add(nw1);
> >> >
> >> > --
> >> > Thanks & Regards
> >> > Tejesh
> >> >
> >> > _______________________________________________
> >> > Users mailing list
> >> > Users at ovirt.org
> >> > http://lists.ovirt.org/mailman/listinfo/users
> >> >
> >>
> >
> >
> >
> > --
> > Thanks & Regards
> > Tejesh
> >
> 
> 
> 
> --
> Thanks & Regards
> Tejesh
>