[Users] vlan on mgmt network

[jplorier at gmail.com]

Hi Peter,

Try to check if ovirmgmt is defined in the vlan you desire (or without
vlan). Maybe when you sync ovirt is trying to configure the network with
options  different from what you desire. I never got ovirt to finish
properly to install a host, it fails to get ovirtmgmt working right so I
always manually configure the vlan interfaces and the ovirtmgmt bridge in
the hosts. You can get your host back if you manually correct the network,
also you may take a look of what ovirt configured to try to find out if
something is not set properly in the network definition.
Regards
El ene 18, 2014 7:56 PM, "Peter Styk" <polfilm at gmail.com> escribió:

>
>
> On 18 January 2014 17:11, Itamar Heim <iheim at redhat.com> wrote:
>
>> On 01/18/2014 04:52 PM, Peter Styk wrote:
>>
>>> So I got ovirtmgmt VM ticked off. Had to remove it from all VM's then
>>> tried to add new Logical network to eth0 by drag & drop but refused
>>> since ovirtmgmt was out of sync. So I synced it. ....and that's how I
>>> lost access to my hosted remote system. End of story. So that's it I
>>> guess, automated install doesn't work (during switch network goes dead
>>> and doesn't come back remote access is lost) so I found manual way that
>>> works. But then I need to sync it to get my ovirtmgmt not to be a VM
>>> network. And even if its not to get another network on the interface i
>>> need to sync it.....
>>>
>>
>> this sounds like a bug - can you provide clear reproduction steps?
>
>
> Reproduction steps are in network configuration alone. After installing
> Engine, i have to set up network to the config listed here:
> http://styk.tv/wp-content/uploads/2014/01/oVirtHosted1_almost_working.png.
> Unfortunately can't rely on engine-vdsm duo to help out.
>
> Anything above the host line on the diagram is physical setup and is the
> only configuration that doesn't disconnect me from the net.  Only thing
> missing on the diagram is ifcfg-eth0 has also HWADDR attribute with MAC
> address of physical eth0 device.
>
> Once this survives service network restart I can proceed to VDSM install
> and then its straight forward....that is until I'm trying to SYNC ovirtmgmt
> on host inside. I should mention after ovirt engine is working I destroy
> default cluster and create new local one.
>
> Obviously I cannot access logs since access to host is no longer but
> entire setup is scripted including provisioning so I can easily rebuild
> entire setup within 15 or so minutes by running a script. Anyone who would
> like to benefit from my findings can use this script and gain access to my
> host and learn with me on how to overcome this.
>
> Script will provision the host (fresh os install), log in, get the files:
> ifcfg-eth0, ifcfg-ovirtmgmt, ifcfg-ovirtmgmt-range0, ovrit_answers and
> route-ovirtmgmt, then install epel 6-8, install pgp, localinstall
> ovirt-el6.10-1. install bridge-utils, upgrade, set hostname, then after
> reboot ssh alive, set local data,images,iso folders, install ovrit-engine,
> set ipv4 forwarding and proxy_arp=1, restart-network, and run engine-setup
> with ovirt_answers including cli and stop iptables as engine and vdsm rules
> still prevent connection if on. that's it. working system in 15 mins
>
> still to do is engine-api calls to create local cluster, join engine with
> vdsm local and setup private network with pfSense instance as
> router/nat/dhcp for 10.0.0.0/24
>
> Peter
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20140118/7ebf5927/attachment-0001.html>