[ovirt-users] Network usage is not updating in the ovirt panel

Lior Vernia lvernia at redhat.com
Tue Oct 7 11:24:41 UTC 2014


Hi Shanil,

This file transfer should have been below the traffic threshold to be
displayed; as you can see in your third screenshot, the average transfer
rate was 213 KBps, which is about 1.5 Mbps, which is about 0.15% of the
NICs' speed - whereas you'd only see traffic above 1%.

You would need a higher-intensity transfer to verify... And in fact,
using your QoS settings, you will never see any traffic, as your traffic
limit is only 0.2% of the NICs' speed!

And for future reference, when you take screenshots of the VM/interfaces
secondary tab, it's best that you also click on the specific VM
interface that should see the traffic - so its RX/TX rate is displayed
in the "statistics" tab at the bottom-right.

Yours, Lior.

On 07/10/14 12:00, Shanil S wrote:
> Hi Lior,
> 
> As per your suggestion i have created two vm's with ip .46 and .47 and
> transfer 100MB file from vm1 (.46) to vm2(.47) but even after 7 min of
> transaction ovirt portal doesn't display any stats or network usages...
> I have attached the screenshots pleas have a look at this.
> 
> -- 
> Regards
> Shanil
> 
> On Tue, Oct 7, 2014 at 2:33 PM, Lior Vernia <lvernia at redhat.com
> <mailto:lvernia at redhat.com>> wrote:
> 
>     Hi Shanil,
> 
>     QoS doesn't have much to do with this, I'm more interested in knowing
>     how much traffic is in fact going in to and out of the VM (QoS defines
>     limits, not actual traffic).
> 
>     From your screenshots it seems that there really isn't significant
>     traffic on the VMs. Could you try initiating a file transfer between two
>     VMs that would last more than 15 seconds (this is the rate at which the
>     GUI is updated) and see if the GUI reflects the traffic in that case?
> 
>     Yours, Lior.
> 
>     On 07/10/14 05:15, Shanil S wrote:
>     > Hi Lior,
>     >
>     > Thanks for your reply.
>     >
>     > We have set network QOS as 2Mbps for the VM, i have attached the
>     > screenshots please check it.
>     >
>     >
>     > --
>     > Regards
>     > Shanil
>     >
>     > On Mon, Oct 6, 2014 at 5:15 PM, Lior Vernia <lvernia at redhat.com <mailto:lvernia at redhat.com>
>     > <mailto:lvernia at redhat.com <mailto:lvernia at redhat.com>>> wrote:
>     >
>     >     Hi Shanil,
>     >
>     >     It might help if you provide screenshots where you scroll right in the
>     >     interfaces subtabs, so that the RX/TX columns are visible.
>     >
>     >     Could it be that the vNIC speed is configured to be large enough for
>     >     standard traffic to be negligible (i.e. <1% of vNIC speed)?
>     >
>     >     Yours, Lior.
>     >
>     >     On 06/10/14 11:09, Shanil S wrote:
>     >     > Hi,
>     >     >
>     >     > We are using the ovirt version 3.4.3, it seems the network usage
>     >     is not
>     >     > showing correctly in the ovirt panel. What may be the reasons ? I have
>     >     > attached the screenshots, please check it.
>     >     >
>     >     >
>     >     > --
>     >     > Regards
>     >     > Shanil
>     >     >
>     >     >
>     >     > _______________________________________________
>     >     > Users mailing list
>     >     > Users at ovirt.org <mailto:Users at ovirt.org>
>     <mailto:Users at ovirt.org <mailto:Users at ovirt.org>>
>     >     > http://lists.ovirt.org/mailman/listinfo/users
>     >     >
>     >
>     >
> 
> 



More information about the Users mailing list